Brother RH-9800 Instruction Manual page 34

6. USING THE OPERATION PANEL AND FRONT PANEL
No.
Y direction offset for return seam to prevent
07
thread breakage
Sewing end pitch for buttonhole taper to
08
prevent fraying
No. of stitches before pitch change for memory
switch No. 08
09
* Does not appear when memory switch No. 08
is set to OFF.
No. of stitches after pitch change for memory
switch No. 08
10
* Does not appear when memory switch No. 08
is set to OFF.
11 Test feeding speed
Speed for memory switch No. 11
* Does not appear when memory switch No. 11
12
is set to OFF.
13 Knife operation (BEFORE/OFF/AFTER) setting
14 Special lapel cutting device
Button hole sensor (Special lapel cutting
15
device)
Timer for checking lowering of cutting block
16 (Timer for determining if cutting block is
lowered)
Time for memory switch No. 16
17 * Does not appear when memory switch No. 16
is set to OFF.
Changing cutting block ON time
18 * Disabled (always "OFF") when memory
switch No. 16 is "ON"
Time for memory switch No. 18
19 * Does not appear when memory switch No. 18
is set to OFF.
Timer for checking raising of cutting block
(Timer for determining if the cutting block has
20
been raised to a position where it will not touch
the next feed bracket to operate)
Time for memory switch No. 20
21 * Does not appear when memory switch No. 20
is set to OFF.
Cutting block raising check timer
(Raised position of the cutting block is
determined from the number of slit signals, and
22
timer is updated)
* Disabled (always "OFF") when memory
switch No. 20 is "ON"
Time for memory switch No. 22
23 * Does not appear when memory switch No. 22
is set to OFF.
Setting tacking length to 0 for straight tacking
24
specifications
25
Spare
99
28
Contents Setting range
OFF: No offset
ON: Offset by 1/2 pitch
OFF: No change
ON: Change
01: 1 stitch, 02: 2 stitches, 03: 3 stitches,
04: 4 stitches, 05: 5 stitches
01: 1 stitch, 02: 2 stitches, 03: 3 stitches,
04: 4 stitches, 05: 5 stitches, 06: 6 stitches,
07: 7 stitches, 08: 8 stitches, 09: 9 stitches
OFF: Standard speed
ON: Low speed
20: 20% of standard speed
35: 35% of standard speed
50: 50% of standard speed
OFF: Setting not possible within cycle program
ON: Setting possible within cycle program
OFF: Disabled
ON: Enabled
OFF: Disabled
ON: Enabled
OFF:Disabled (Determined
stopping)
ON: Enabled (Determined by timer)
42: 420 ms, 45: 450ms, 48: 480ms,
51: 510ms, 54: 540 ms
OFF: Disabled (25 ms)
ON: Enabled
05: 50 ms, 10: 100ms,
15: 150ms, 20: 200 ms
OFF: Disabled (Determined from number of slit
signals)
ON: Enabled (Determined by timer)
15: 150ms, 20: 200 ms, 25: 250ms,
30: 300ms, 35: 350ms, 40: 400ms,
45: 450ms, 50: 500ms
OFF: Disabled
ON: Enabled
05: 50 ms, 10: 100ms, 15: 150ms,
20: 200 ms, 25: 250ms, 30: 300ms,
35: 350ms, 40: 400ms
OFF: Disabled
ON: Enabled
-
RH-9800
Initial
value
OFF
OFF
01
01
OFF
50
OFF
OFF
OFF
from slit signal
OFF
45
OFF
05
OFF
20
OFF
05
OFF
-