Quick Start Guide For Preset Programming - Behringer FCB1010 User Manual

8
MIDI FOOT CONTROLLER FCB1010 User Manual
2.2.3 CONFIG page
The CONFIG LED lights up if you are on CONFIGURATION page. The following
functions, recalled via the footswitches (as in table 2.2), are at your disposal:
Switch Function Action
Determines whether the UP switch controls SWITCH 1
1 SWITCH 1
relay ("toggle") with DIRECT SELECT on.
Determines whether the DOWN switch controls
2 SWITCH 2
Switch 2 relay ("toggle") with DIRECT SELECT on.
5 COPY PRESET Enables copying presets (see ch. 2.4.1).
6 SYSEX SEND Sends the entire memory as a sysex dump.
When this switch is pressed, the FCB1010 waits
for the reception of system-exclusive data.
7 SYSEX RCV
Switch LED goes out when the data have been
received correctly.
Allows to merge MIDI IN data with FCB1010-
8 MERGE generated data. The combined data stream is
subsequently output at the MIDI OUT.
Enables/disables Running Status feature. Serves to
RUNNING make efficient use of the MIDI transmission rate.
9
STATUS The MIDI Status Byte from the Expression Pedals is
sent only if it differs from the preceding Status Byte.
Tab. 2.2: Assignment of footswitches in CONFIGURATION setup menu
◊
External equipment, for example guitar or bass amps, can be
controlled by using SWITCH 1 and 2 outputs of the FCB1010. If the
FCB1010 triggers this function, you should first check if the piece
of equipment you are trying to control reacts to connection state
(contact open or closed) or current feed (contact closed as long as
the switch is depressed). BEHRINGER guitar and bass amps react to
current feeds. Therefore, when you wish to remotely control channel
change on a BEHRINGER guitar amp not via MIDI but via switch outputs
(because you have no MIDI cable at your disposal), you have to power
off switch 1 & 2 LEDs in GLOBAL CONFIGURATION menu under CONFIG.
These LEDs are on in the default setting and indicate that programmed
connection state is kept.
Basically, CONFIGURATION mode functions are active as long as the corresponding
footswitch LED is lit.

2.3 Quick start guide for PRESET programming

UP
VALUE 1
NUMBER
UP
SELECT
UP
DOWN
SWITCH
Fig. 2.4: PRESET programming
For each of the 100 PRESETS you can determine which MIDI functions shall be
transmitted as soon as you select the respective PRESET. For instance, you can
send five different program change commands, two controller commands,
UP
VALUE 2
UP
two different controller values (using the expression pedals) and a Note On
command to the connected equipment at the same time (menu structure as in
fig. 2.4). It is up to you to determine, which commands are stored in a Preset.
Do as follows to program the functions to be sent with each PRESET:
• Select the PRESET you wish to edit
• Press DOWN for more than 2.5 sec to enter PRESET programming mode.
The number in the display disappears while the green SWITCH 1/SWITCH2
LED in the display starts flashing
• Use footswitches 1 and 2 to edit the status of the SWITCHES. The current
status is indicated by the foot- switch LED and the corresponding
SWITCH LED in the acrylic display. For further details see chapter 3.3
"Connections (general)"
◊
Please note that the status of the SWITCHES can also be toggled with
UP (SWITCH 1) and DOWN (SWITCH 2) if DIRECT SELECT is enabled.
The only prerequisite is that this function has been enabled for both
SWITCHES in the CONFIGURATION menu.
• Confirm with UP/ENTER. The SELECT LED in the display lights up
• Activate individual MIDI functions by keeping the respective footswitch
depressed for roughly 1.5 sec. Footswitch LEDs indicate the activated
footswitches of the respective MIDI functions. As long as the display
indicates SELECT, you can activate MIDI functions and select them for editing
by briefly pressing the corresponding footswitch. The selected footswitch
LED and the display blink during selection and activation. The NUMBER LED is
also lit. The following MIDI functions are available for selection:
Switch MIDI function Action
1 PRG CHG 1 Program change command #1
2 PRG CHG 2 Program change command #2
3 PRG CHG 3 Program change command #3
4 PRG CHG 4 Program change command #4
5 PRG CHG 5 Program change command #5
6 CNT 1 Controller 1
7 CNT 2 Controller 2
8 EXP A Expression Pedal A
9 EXP B Expression Pedal B
10/0 NOTE Transmits a MIDI note
Tab. 2.3: Footswitch assignment in PRESET programming mode
◊
MIDI channel adjustment for the respective MIDI functions is not done
during preset programming; it is done in GLOBAL CONFIGURATION on
MIDI FUNCTION page (see ch. 2.2.2).
• Confirm your selection with UP/ENTER, in order to start programming the
selected MIDI function, or cancel with DOWN/ESCAPE. Use footswitches
1 through 10/0 or EXPRESSION PEDAL A to enter the parameter values of
your choice
• If you have selected PROGRAM CHANGE as the MIDI function to be edited,
you can now enter a program change number from 1 through 128 and
confirm your selection with UP/ENTER
• If you have selected CNT1 or CNT2, you can now enter the number of the
controller to be sent (0 through 127) when you press the corresponding
footswitch. After confirming your selection with UP/ENTER you can select a
controller value (0 through 127). Confirm your selection with UP/ENTER
• If you have selected EXP A or EXP B, you can now enter the controller