Programming The Fcb1010; Rear Panel; Selecting Banks And Presets - Behringer FCB1010 User Manual

6
MIDI FOOT CONTROLLER FCB1010 User Manual

1.3.2 Rear panel

(7)
(8) (9)
Fig. 1.2: Rear panel connectors
(7) FUSE HOLDER / VOLTAGE SELECTOR. Please make sure that your local
voltage matches the voltage indicated on the unit, before you attempt
to connect and operate the FCB1010. Blown fuses may only be replaced
by fuses of the same type and rating. Some models allow for inserting
the fuse holder in two different positions, in order to switch over from
230-V to 120-V operation, and vice versa. Please note that for 120-V
operation outside Europe, you need to use a fuse of a higher rating
(see chapter 6 "Specifications").
(8) IEC POWER CONNECTOR. Use the enclosed power cord to connect the unit
to the mains.
(9) Use the POWER switch to power up your FCB1010. Always make sure the
POWER switch is in its "Off" setting when you connect the FCB1010 to
the mains.
◊ Attention: The POWER switch does not physically disconnect the unit
from the mains. Always unplug the unit from the mains when you do
not plan on using it for prolonged periods of time.
(10) SERIAL NUMBER. Please take the time to have the warranty card filled out
completely, and return it within 14 days after the date of purchase, so as
to be entitled to benefit from our extended warranty. Or use our online
registration option available on the World Wide Web under behringer.com.
Fig. 1.3: Rear panel connectors
(11) SWITCH 1 and 2. Use these jacks to connect your amplifier for channel
selection (mono or stereo phone jack cable).
(12) MIDI IN. The MIDI IN of your FCB1010 connects to a sequencer or similar
device, in order to download the memory data saved before with
the help of the MIDI SysEx function. Additionally, data can be looped
through the FCB1010 and merged with other data using the MIDI MERGE
function. Subsequently, the combined data are available at the
MIDI OUT/THRU connector.
(13) MIDI OUT/THRU. Use this jack to connect the devices you wish to control
from your FCB1010. The SOFT THRU circuit allows you to loop through any
signals present at the MIDI IN of your FCB1010, merge them with the unit's
own data stream, and finally output the combined data at the MIDI OUT.
(10)
(11) (12) (13)

2. Programming the FCB1010

In this chapter you will learn to program your FCB1010 and adapt it to your
specific MIDI set-up. But don't worry, you won't have to learn a programming
language before you could give your FCB1010 a single MIDI command. The unit
will perform all functions for you, one after the other. Simply make and confirm
your choices. If particular functions prompt you to enter a parameter, this will be
covered specifically.

2.1 Selecting BANKS and PRESETS

There are two options to select a BANK and the PRESETS it contains. Which one
you use depends on the DIRECT SELECT parameter in the GLOBAL CONFIGURATION
menu. If DIRECT SELECT is on, you can use the PRESET footswitches to directly
select the BANK number followed by the PRESET number. If DIRECT SELECT is
off, you need to step through the various BANKS (using the UP/DOWN switches),
then select a PRESET from a bank. The default setting is OFF. The illustrations
below show the two options.
2.1.1 DIRECT SELECT deactivated
Let's assume you wish to select PRESET #1 from BANK #3...
Step 1
Use the UP/DOWN switches to go to the BANK that contains the PRESET of your
choice (here: BANK #3).
Step 2
Select the PRESET you wish to use (here: PRESET #1).
Step 2
Fig. 2.1: PRESET selection with DIRECT SELECT disabled
2.1.2 DIRECT SELECT activated
If DIRECT SELECT is on, do as follows to select PRESET #1 from BANK #3
(activating DIRECT SELECT is discussed in ch. 2.2.1):
Step 1
Select the BANK of your choice (here: BANK #3) by stepping on footswitch #3.
Step 2
Select the PRESET you wish to use (here: PRESET #1) by stepping on footswitch
#1. The display shows that preset 31 is selected.
Step 1