9
MIDI FOOT CONTROLLER FCB1010 User Manual
number the EXPRESSION PEDAL of your choice is aimed to send values for.
Confirm your selection with UP/ENTER and enter the lower value (pedal up).
Confirm with UP/ENTER
•
Afterwards, enter the upper value (pedal pressed down completely)
and confirm once again with UP/ENTER
◊
Please keep in mind that the first controller value always has to be
lower than the second controller value!
◊
You can quit the programming mode at any time by means of a long
press on DOWN. Any confirmed entries will be stored with the currently
selected PRESET.
◊
How to program the NOTE function is explained in chapter 2.4.6.
2.4 Detailed PRESET programming
2.4.1 Preset copy function
The preset copy function copies an already programmed preset to a new preset of
your choice. This saves you time, since you do not have to repeat all adjustments
for each newly programmed preset.
•
Activate CONFIG in the GLOBAL CONFIGURATION (see chapter 2.2)
•
Now, press footswitch 5 to activate the copy function. The VALUE 1 LED lights
up. The number in the display and the footswitch LED start flashing
•
Enter the number of the preset you wish to copy and confirm your selection
with UP/ENTER. The VALUE 2 LED lights up. The number in the display and
the footswitch LED start flashing
◊
Presets 1 - 10 are stored in bank 0, presets 11 - 20 in bank 1, and so on.
•
Enter the target preset and confirm your selection with UP/ENTER, or cancel
with DOWN/ESCAPE
•
If you want to copy further presets, please press footswitch 5 again.
Press and hold DOWN/ESCAPE to quit the GLOBAL CONFIGURATION
2.4.2 Programming switches
•
Select the PRESET you wish to edit
•
Press DOWN for more than 2.5 sec to enter PRESET programming mode.
The green SWITCH 1/SWITCH 2 LED in the display starts flashing
•
Enable/disable the SWITCHES using footswitches 1 and/or 2 and confirm your
selection with UP/ENTER. The corresponding footswitch and SWITCH LEDs
light up
•
Exit PRESET programming mode through keeping the DOWN/ESCAPE key
for a few seconds, or press the UP/ENTER key in order to get to the next
page, where you can edit various MIDI functions for the preset selected at
the beginning
2.4.3 Programming program changes
•
Select the PRESET you wish to edit
•
Keep the DOWN/ESCAPE key pressed longer than 2.5 sec. to get to the
programming mode. The green SWITCH 1/SWITCH 2 LED in the display
starts flashing
•
Use the UP/ENTER key to get to the next page. The SELECT LED in the display
is lit
◊
To program a MIDI function, you have to first activate it. Individual
MIDI functions are activated by keeping the corresponding keys
pressed for a few seconds. Active MIDI functions are indicated by a
permanently lit footswitch LED.
•
Select the PROGRAM CHANGE you wish to program for the selected
PRESET by briefly pressing the respective footswitch (footswitches 1 to 5).
The footswitch LED blinks
•
Confirm your selection by pressing UP/ENTER. The NUMBER LED in the display
lights up
•
Enter the program change command (1 bis 128) via the footswitch or
expression pedal A
•
Confirm your selection by pressing UP/ENTER or cancel by pressing
DOWN/ESCAPE. The SELECT LED in the display lights up
•
Select an additional MIDI function you wish to edit or exit the PRESET
programming mode by keeping the DOWN/ESCAPE key for a few seconds
2.4.4 Programming CONTROL CHANGES
•
Select the PRESET you wish to edit
•
Keep DOWN pressed for more than 2.5 sec to enter PRESET programming
mode. The green SWITCH 1/SWITCH 2 LED in the display starts flashing
•
Use the UP/ENTER key to get to the next page. The SELECT LED in the display
lights up
◊
To program a MIDI function, you have to first activate it. Individual
MIDI functions are activated by keeping the corresponding keys
pressed for a few seconds. Active MIDI functions are indicated by a
permanently lit footswitch LED.
•
Keep the corresponding footswitch (foot key 6 or 7) pressed for a few
seconds to activate the controller you wish to edit. The controller is selected
by pressing the key briefly again. The LED blinks
•
Confirm your selection by pressing UP/ENTER. The NUMBER LED in the display
lights up
•
Enter the desired controller number (0 to 127) by using the foot keys or the
expression pedal A
•
Confirm your selection with UP/ENTER. The VALUE 1 LED in the display
lights up
•
Use the footswitches 1 through 10/0 or EXPRESSION PEDAL A to enter the
controller value (0 through 127)
◊
To correct your selection, use the DOWN/ESCAPE key to go one
step backward.
•
Confirm your selection by pressing UP/ENTER. The SELECT LED in the display
lights up
•
Select an additional MIDI function you wish to edit or quit the PRESET
programming mode by keeping DOWN/ESCAPE pressed for a few seconds
2.4.5 Programming EXPRESSION PEDALS A/B
•
Select the PRESET you wish to edit
•
Keep DOWN pressed for more than 2.5 sec to enter PRESET programming
mode. The green SWITCH 1/SWITCH 2 LED in the display starts flashing
•
Use UP/ENTER to get to the next page. The SELECT LED in the display begins
to light up