4 .
4 .
4 . 4 .
S e r i a l A T A c o n n e c t o r s
S e r i a l A T A c o n n e c t o r s
S e r i a l A T A c o n n e c t o r s
4 .
S e r i a l A T A c o n n e c t o r s
S e r i a l A T A c o n n e c t o r s
( 7 - p i n S A T A 1 [ r e d ] , S A T A 2 [ r e d ] , S A T A 3 [ b l a c k ] ,
( 7 - p i n S A T A 1 [ r e d ] , S A T A 2 [ r e d ] , S A T A 3 [ b l a c k ] ,
( 7 - p i n S A T A 1 [ r e d ] , S A T A 2 [ r e d ] , S A T A 3 [ b l a c k ] ,
( 7 - p i n S A T A 1 [ r e d ] , S A T A 2 [ r e d ] , S A T A 3 [ b l a c k ] ,
( 7 - p i n S A T A 1 [ r e d ] , S A T A 2 [ r e d ] , S A T A 3 [ b l a c k ] ,
S A T A 4 [ b l a c k ] )
S A T A 4 [ b l a c k ] )
S A T A 4 [ b l a c k ] )
S A T A 4 [ b l a c k ] )
S A T A 4 [ b l a c k ] )
These connectors are for the Serial ATA signal cables for Serial ATA
hard disk drives.
If you installed Serial ATA hard disk drives, you can can create a RAID
0 or RAID 1 configuration with the Intel
through the onboard Intel
for information on creating a RAID configuration.
These connectors are set to Standard IDE configuration by default. In
Standard IDE mode, you can connect Serial ATA boot/data hard disk
drives to these connectors. If you intend to create a Serial ATA RAID set
using these connectors, set the C o n f i g u r e S A T A A s
to RAID. See section "4.3.6 IDE Configuration" for details.
P5GDC-V
P5GDC-V SATA connectors
I m p o r t a n t n o t e s o n S e r i a l A T A
I m p o r t a n t n o t e s o n S e r i a l A T A
I m p o r t a n t n o t e s o n S e r i a l A T A
I m p o r t a n t n o t e s o n S e r i a l A T A
I m p o r t a n t n o t e s o n S e r i a l A T A
•
These connectors support the Intel
•
The Serial ATA RAID feature (RAID 0, RAID 1) is available only if you
are using Windows
•
Install the Windows
Service Pack1 before using Serial ATA.
•
Use only a maximum of 2 ports for each RAID 0 or RAID 1 set.
•
Plug your Serial ATA boot disk on the master port (SATA1 and
SATA2) to support S3 function. Refer to the table below for details.
Serial ATA Master/Slave connectors
Serial ATA Master/Slave connectors
Serial ATA Master/Slave connectors
Serial ATA Master/Slave connectors
Serial ATA Master/Slave connectors
C o n n e c t o r
C o n n e c t o r
C o n n e c t o r
C o n n e c t o r
C o n n e c t o r
S A T A 1 , S A T A 2
S A T A 1 , S A T A 2
S A T A 1 , S A T A 2
S A T A 1 , S A T A 2
S A T A 1 , S A T A 2
S A T A 3 , S A T A 4
S A T A 3 , S A T A 4
S A T A 3 , S A T A 4
S A T A 3 , S A T A 4
S A T A 3 , S A T A 4
A S U S P 5 G D C - V D e l u x e
A S U S P 5 G D C - V D e l u x e
A S U S P 5 G D C - V D e l u x e
A S U S P 5 G D C - V D e l u x e
A S U S P 5 G D C - V D e l u x e
®
®
ICH6R RAID controller. Refer to Chapter 5
C o n f i g u r e S A T A A s
C o n f i g u r e S A T A A s
C o n f i g u r e S A T A A s
C o n f i g u r e S A T A A s item in the BIOS
SATA3
SATA1
®
2000/XP.
®
2000 Service Pack 4 or the Windows
C o l o r
C o l o r
C o l o r
S e t t i n g
S e t t i n g
S e t t i n g
C o l o r
C o l o r
S e t t i n g
S e t t i n g
Red
Master
Black
Slave
Matrix Storage Technology
SATA4
SATA2
®
Matrix Storage Technology.
U s e
U s e
U s e
U s e
U s e
Boot Disk
Data Disk
®
XP
2 - 3 1
2 - 3 1
2 - 3 1
2 - 3 1
2 - 3 1