Anti-Tip Stability Device Installation Instructions - Viking VGIC245 Installation Manual

BASIC SPECIFICATIONS
Description 48" W. Models
Overall width
47-7/8" (121.6 cm)
Overall height 24" Deep Models
To top of grate support -
Min. 35-7/8 " (91.1 cm) to
Max. 37-5/8" (95.6 cm)
Legs adjust 1-3/4" (4.5 cm)
Additions to Base Height
To top of spider grate -
To top of island trim -
To top of 6" backguard -
To top of 10" backguard -
To top of high shelf -
Overall depth from rear
To end of side panel -
To end of control panel -
To end of knobs -
Electrical requirements 120 VAC/60 Hz; 4 ft. (121.9 cm), 3-prong plug attached to unit
Gas requirements
Shipped natural or LP/Propane gas; convert with conversion kit (purchased separately)
Maximum amp usage/ 6G - 16.0 amps
6Q - 12.4 amps
4GQ - 16.0 amps
Surface burner rating
Griddle burner rating 12" / 18" Wide
15,000 BTU Nat./12,500 BTU LP
(4.4 kW/3.7 kW)
Grill burner rating 12" - 1@ 18,000 BTU Nat. (5.3 kW)/16,000 BTU LP (4.7 kW)
24" - 2@ 13,000 BTU Nat./LP (4.4 kW)
Broil rating
Bake rating Right - Two 15,000 BTU ea. Nat./LP
(Two 4.4 kW ea.)
Left - One 15,000 BTU ea. Nat./LP
(One 4.4 kW ea.)
Oven Interior width Right - 24-1/8" (61.3 cm)
Left - 13-3/8" (34.0 cm)
Oven Interior height 24" D. Models
Both - 16-1/8" (41.0 cm)
27" D. Models
Both - 14-1/8" (35.9 cm)
Oven Interior depth 24" D. Models
Right - 17-5/8" (44.8 cm)
Left - 18-3/4" (47.6 cm)
27" D. Models
Right - 19-1/4" (48.9 cm)
Left - 21-1/4" (54.0 cm)
Oven Interior overall size 24" D. Models
Right - 4.0 cu. ft.
Left - 2.3 cu. ft
27" D. Models
Right - 3.8 cu. ft.
Left - 2.3 cu. ft
Approximate Shipping wt. 6G - 591 lb. (266.0 kg) 4Q - 586 lb. (263.7 kg)
6Q - 586 lb. (263.7 kg) 4G - 596 lb. (268.5 kg)
4GQ - 596 lb. (268.5 kg)
(For Minimum Clearances from adjacent combustible construction refer to bottom of page 4.)
60" W. Models
59-1/2" (151.1 cm)
Base Height 27" Deep Models Base Height
Min. 36-1/8" (91.8 cm
Max 39-1/8" (99.4 cm)
Legs adjust 3" (7.6 cm)
add 1-1/8" (2.9 cm)
add 1-1/4" (3.2 cm)
add 6" (15.2 cm)
add 10" (25.4 cm)
add 23-1/2" (59.7 cm)
24" Deep Models 27" Deep Models
24-15/16" (63.3 cm) 27" (68.6 cm)
27-7/8" (70.8 cm) 28-3/4" (73.0 cm)
28-3/8" (72.0 cm) 30-3/8" (77.2 cm)
4Q - 12.4 amps 6G - 23.6 amps
4G - 19.6 amps 6GQ - 20.0 amps
15,000 BTU Nat./13,500 BTU LP
(4.4 kW/4.0 kW)
24" Wide
Two 15,000 BTU ea. Nat./12,500 BTU ea. LP
(Two 4.4 kW ea./3.7 kW ea.)
18,000 BTU Nat./16,000 BTU LP
(5.3 kW/4.7 kW)
Two 15,000 BTU ea. Nat./LP
(Two 4.4 kW ea.)
Two 15,000 BTU ea. Nat./LP
(Two 4.4 kW ea.)
Both - 24-1/8" (61.3 cm)
27" D. Models
Both- 14-1/8" (35.9 cm)
27" D. Models
Both - 19-1/4" (48.9 cm)
27" D. Models
Both - 3.8 cu. ft.
6G - 762 lb. (342.9 kg)
6GQ - 757 lb. (340.7 kg)
8
BACK TRIM ACCESSORIES
Assembly and installation instructions are included with all back trim accessories.

ANTI-TIP STABILITY DEVICE INSTALLATION INSTRUCTIONS

1. The anti-tip bracket is to be attached to the rear wall as shown. The dimension for the bracket location from the
floor is to be determined after the range legs have been adjusted to the proper installation height shown in the
installation instructions and the range has been leveled.
2. Measure from the floor to the bottom of the anti-tip opening located on the back of the range.
3. Locate the anti-tip bracket on the wall at the measure dimension plus 1/16" (0.16 cm) clearance and attach securely
with provided toggle bolts.
4. Slide range into place. Be sure the bottom rear flange on the rear of the range slides under the bracket attached to
the rear wall.
Item "A"
Figure 1
To be determined after the range legs have been adjusted.
RANGES EQUIPPED WITH CASTERS
1. Adequate means must be provided to limit the movement of
castered ranges without depending on the connector and/or
quick disconnect device. This "restraint" should be inspected
as part of the maintenance and safety procedure. Restraint
cable must be connected at all times when range is in use.
2. When using the quick disconnect device and/or casters, the
"restrainer" must be attached to the wall and to the rear of
the range.
3. If disconnection of the restraint is necessary, ensure the
restraint is reconnected after the range has been returned to
its original position.
Figure 2
Item "B"
Bottom rear flange
9