Remote Control; General - Insignia NS-46E790A12 User Manual

Problem Solution
Good picture, but no sound.
•
• Make sure that the sound is not muted.
• Disconnect the headphones.
• Make sure that the correct audio mode is
• Make sure that the audio cables are connected
• Make sure that the antenna or cable TV is
• If you are using an antenna, the digital channel
• The audio cable(s) you are using may be bad. Try
Poor picture
• Make sure that the room is not too bright. Light
• If an S-VHS camera or a camcorder is connected
Good sound but poor color
•
Audio noise
• Other devices (for example, surround sound
No output from one of the
• Adjust the audio balance. See "Adjusting sound
speakers
• Make sure that the audio cables are connected
After images appear
• Do not display a still image, such as a logo,
48
Increase the volume.
selected.
correctly and securely to the back of your TV.
connected correctly and securely. See
"Connecting a cable or satellite box" on page 10
or "Connecting an antenna or cable TV (no box)"
on page 13.
signal may be low. To check the digital channel
signal strength, see "Checking the digital signal
strength" on page 30.
a new set.
reflecting off the screen can make the picture
difficult to see.
while another connected device is turned on,
the picture may be poor. Turn off one or more
devices.
Adjust the contrast, color, and brightness
settings.
receiver, external speakers, fans, or hair dryers)
may be interfering with your TV. Try turning off
one device at a time to determine which device
is causing interference. After you have
determined which device is causing
interference, move it further from the TV to
eliminate the interference.
settings" on page 27.
correctly and securely to the back of your TV.
game, or computer image, for an extended
period of time. This can cause a permanent
after-image to be burned into the screen. This
type of damage is not covered by your warranty.
www.insigniaproducts.com
NS-46E790A12 Insignia 46" LED-LCD HDTV, 1080p

Remote control

Problem Solution
Remote control does not
• Make sure that the power cord is correctly
work.
• Make sure that there are no obstructions
• Point the remote control directly at the remote
• The supplied batteries are wrapped tightly in
• Make sure that the batteries are installed
• Replace dead batteries with new batteries. See
Trouble programming your
• See instructions and a table of common codes in
existing universal remote
control.
• Codes are subject to change. For up-to-date
• Replace dead batteries with new batteries. See
• Refer to the User Guide that accompanied your

General

Problem Solution
No power
• Make sure that the power cord is correctly
connected to your TV and a power outlet.
• Unplug the power cord, wait 60 seconds, then
plug the cord back in and turn on your TV.
• Other devices (for example, surround sound
receiver, external speakers, fans, or hair dryers)
may be interfering with your TV. Try turning off
one device at a time to determine which device
is causing interference. After you have
determined which device is causing
interference, move it further from the TV to
eliminate the interference.
"No signal" error
• Press INPUT and make sure that you have
message is displayed
selected the correct input for the device or
service you are trying to use.
• If you are using a cable or satellite box, use the
remote that came with that box to change
channels.
• Make sure you have the correct input selected to
view channels from the cable or satellite box.
After Auto Channel
• Reception can vary by channel depending on the
Search, there are no
broadcast power level of a given station. Contact
channels
your cable or satellite TV provider.
• Make sure the antenna or cable/satellite TV is
connected securely to your TV.
• Try replacing the cable between the
antenna/cable or cable/satellite box and your
TV.
connected to your TV and a power outlet.
between the remote control and the remote
control sensor on the front of the TV.
control sensor on your TV. For the location of the
remote control sensor, see "Front" on page 6.
clear plastic. Make sure that you have removed
this plastic from the batteries.
correctly. See "Installing remote control
batteries" on page 19.
"Installing remote control batteries" on page 19.
"Programming universal remote controls" on
page 50.
codes, go to
www.insigniaproducts.com/remotecodes.
"Installing remote control batteries" on page 19.
universal remote control and contact the
manufacturer if problems persist.