Table of Contents
Advertisement
DVD
Setting Up the Display Options
Setup
Setup
Setup
:
GB
Display Setup
Display Setup
TV Aspect
: 4:3 L-Box
Black Level
NTSC Disc Output
: PAL 60Hz
DVD Out
: Component
DVD
S-Video Connections (for DVD)
SPEAKERS
DVD Only
FRONT R
FRONT L
WOOFER
COMPONENT VIDEO OUT
1
SURROUND R
SURROUND L
CENTER
S-VIDEO OUT
To S-Video Input on Your TV
50
1
With the unit in Stop mode, press the MENU button.
buttons, then OK or ❿ button.
2
Select DVD using
,
"
❷
3
Select Display Setup using
,
buttons, then press the OK
"
❷
or ❿ button.
4
Use the
,
buttons to select the desired item. Then press the
"
❷
OK or ❿ button.
TV Aspect
Depending on the type of television you have, you may want
to adjust the screen setting (aspect ratio).
1. 4:3 Letter Box :
Select when you want to see the total 16:9 ratio screen DVD
supplies, even though you have a TV with a 4:3 ratio screen.
Black bars will appear at the top and bottom of the screen.
2. 4:3 Pan Scan :
Select this for conventional size TVs when you want to see
the central portion of the 16:9 screen. (Extreme left and right
side of movie picture will be cut off.)
3. 16:9 Wide :
You can view the full 16:9 picture on your widescreen TV.
Black Level
Adjusts the brightness of the screen.(On/Off)
NTSC Disc Output
"NTSC" if the screen only has one NTSC-video entrance.
If this is not the case, you can choose to leave " PAL 60Hz"
as is.
DVD Output
Component : Sends COMPONENT signal (Y, Pb, Pr) to
the component video out JACK.
S-Video : Sends S-VIDEO signal to the S-VIDEO OUT JACK.
Video : - Sends COMPOSITE VIDEO signal to Line out JACK.
- Sends COMPONENT INTERLACE signal from
COMPONENT JACK.
The S-Video is only for the DVD player. The tuner and VCR will
still be viewed through the RF or line inputs.
You must follow the "DVD Out" instructions above to activate
your alternative (S-Video) video selection. If your television is
equipped with S-Video input, you can enjoy superior video
quality when watching DVDs with your DVD-VCR.
1
Connect S-Video Out to TV
Connect an S-Video cable from the S-Video Out on the back
panel of the DVD-VCR to the S-Video Input on your television.
Component Connections (for DVD)
Component video output is available only for DVD playback. RF
and Line input are available for Tuner and VCR playback.
If your TV set supports Progressive Scan, it can transmit Pr, Pb, and
Y signals separately, so you can enjoy sharp and clear picture.
What is Progressive Scan?
It is a set of jacks that can provide sharp and clear picture
quality by using twice the number of fields of lines than
component output.
1
Connect the component output of the DVD player to your TV set.
Use the component cable to connect the component output on the
back panel of the DVD-VCR to the component input of your TV.
If you mix up the connections when connecting the component cable,
the picture will appear reddish or bluish.
2
Set your TV to COMPONENT.
Select component input as your TV's AV input. At this point, even
if the picture appears reddish, it is normal.
3
Press the P.SCAN button on the front panel.
If the P.SCAN button on the front panel of the DVD-VCR is
pressed, a green LED will light up and the following message will
be displayed:
To activate Progressive Scan, press OK.
The following message will be displayed and then the picture will
be played in Progressive Scan mode.
4
To deactivate Progressive Scan, press the P.SCAN button again.
If the P.SCAN button on the front panel of the DVD-VCR is
pressed again, a green LED will light up and Progressive Scan
mode will be canceled. Select another mode as your TV's AV input
to view another output of the DVD-VCR.
This is available only for a TV set that supports Progressive Scan.
• While Progressive Scan is active, video, S-video are not
available.
• To activate Progressive Scan, the DVD-VCR must be in Stop
mode.
You can listen to audio sound through Line OUT audio output or
5.1CH speakers while watching Component or S-Video output.
DVD
SPEAKERS
DVD Only
FRONT R
FRONT L
WOOFER
COMPONENT VIDEO OUT
1
GB
SURROUND R
SURROUND L
CENTER
S-VIDEO OUT
To Component
Input on Your TV
Press "OK" to confirm
Prorgessive scan mode.
Otherwise press "RETURN".
Please set your TV to component
input. If your TV doesn't have
Progressive scan mode, there will
be no signal on the screen.
51
Advertisement
Table of Contents
