Advertisement
Product dimensions
Recessed and closet
nstallatlon
:nstructions
Rear view
&
24" +
4
Fire Hazard
l
It Is recommended
that the
washer/dryer
be exhausted to the
outslde.
l
If washer/dryer
Is Installed In a closet,
the dryer MUST be exhausted outslde.
Failure to do so may result In a tire.
28
n
Check
that
you removed
all the
1;11
\
shipping
pieces,
including
the
three shipping
straps with keys.
f
drain
27-l/2"
Ir you do not remove all three shlpplng
straps, your washer/dryer
may "walk" away
from Its locatlon.
To prevent large amounts ot llnt and molsture
trom accumulating
and to malntaln drylng
etflclency,
and to prevent exposure to
possible health hazards, thls appliance
should be exhausted outdoors.
THIS WASHER/DRYER MAY BE INSTALLED
IN A RECESSED AREA OR CLOSET.
The installation
spacing
is in inches and is the
minimum
allowable.
Additional
spacing
should be considered
for
ease of installation,
servicing
and
compliance
with local codes and
ordinances.
If closet door is installed,
the minimum
unobstructed
air openings
in top and
bottom
are required.
Louvered
doors with
equivalent
air openings
are acceptable.
Closet installation
must be exhausted.
Other installations
must use the minimum
dimensions
indicated.
Side view
39 cm
m
=.,cm
(21~5/16ln) j
29
n
Check
that you have all
182.3 cm
(71-314 In)
t
82.6 cm
(32-l/2 In)
Recessed installation
your tools.
front view
side view
13.3 cm
-5-l/4
In)
f
96je5 ly
L
30
n
Turn on water faucets
-
a-
7.4 cm
(3 In) -D
w-w
and check
for leaks. Tighten couplings
if
there is leaking.
31
n
Plug power
supply cord
into grounded
outlet.
32
n
Replace
the access
panel.
E3e
sure to tighten
screws at each
end of the
access
panel.
69.2 cm
(27-l/4 In) -
33
n
Read the Use and Care Guide
Mlnlmum lnstallatlon spacing
Note:
If recessed installation is exhausted, all
spacing
can be 0 cm (0 in).
Additional clearance
for wall, door and floor
molding may be required.
to fully understand
your new washer/dryer.
Now start the washer and allow it to
complete
the regular
cycle.
Closet installation
It
front view
IA
-
309.7 tq.cm
(48 sq. In)
Tf
L-
closet
door
H Remove
tape from drver door
and open dryer door. Remove
tape across
the dryer lint screen.
Check to be sure lint
screen is in its proper
position.
Wipe out drum
with a damp
cloth to remove
any dust. Start
dryer and allow it to complete
a heat cycle
to make sure the dryer is working
properly.
Unobstructed
air openings
are minimum
for closet
door. Louvered
door with equivalent
air openings
is acceptable.
35
H Finally, save all literature
and
keep with washer/dryer.
side view
309.7 sq. cm
(48 sq. In)
-4 +gnc;"
Additional
space
may
be needed
fooywyaust
+I
+
2.5 cm (1 In)
/b!iJii!i!ik-J
To get the most efflclent use from
1 Congratulations!
\
Keep lnstallatlon lnstructlons nearby
~~~~~~~
Closet installation
must be exhausted
outdoors.
Recessed,
non-exhausted
installation
must use
only the rear exhaust
position
and Exhaust
Deflector Kit No. 4500 is required.
Panel E
Advertisement
