Table of Contents
Advertisement
Quick Links
Remote Control Alarm & Remote Engine Starting System
CONGRATULATIONS on your choice of a Super Rage™ Alarm & Remote Engine Starter by Crimestopper Security
Products Inc.
This booklet contains the information necessary for operating your system.
contact your installation dealer or Crimestopper Security Products Inc.
*IMPORTANT INFORMATION: Primary and Optional Features
-PRIMARY:
These are features that must be connected in order for the system to operate properly i.e. Power,
Ground, Lights, Power Locks, etc.
-OPTIONAL: Optional features are connected only if desired or agreed upon by the installing dealer i.e. Horn Honk,
Dome light illumination, Starter Kill, L.E.D., Trunk Pop, etc.
charges. Consult with your installer about these features before installation.
CONTACT INFORMATION:
TECHNICAL SUPPORT (800)-998-6880
Monday - Friday 8:00am - 4:30pm Pacific
Website: www.crimestopper.com
E-mail: tech-support@crimestopper.com
CRIMESTOPPER
SECURITY PRODUCTS, INC.
1770 S. TAPO STREET
SIMI VALLEY, CA. 93063
CS-2011RS Series III
Super Rage™
OPERATION INSTRUCTIONS
INTRODUCTION
REV. A 8.2002 S/W: 620
These features may require additional parts and labor
This device complies with FCC Rules part 15. Operation is subject
to the following two conditions: 1) This device may not cause
interference, and (2) this device must accept any interference that
may be received, including interference that may cause undesired
operation. The manufacturer is not responsible for any radio or TV
interference
caused
by
equipment. Such modification could void the user's authority to
operate the equipment.
If any questions arise,
unauthorized
modification
to
this
Advertisement
Table of Contents
Related Manuals for CrimeStopper CS-2011RS.III
Summary of Contents for CrimeStopper CS-2011RS.III
- Page 1 Remote Control Alarm & Remote Engine Starting System OPERATION INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of a Super Rage™ Alarm & Remote Engine Starter by Crimestopper Security Products Inc. This booklet contains the information necessary for operating your system. If any questions arise, contact your installation dealer or Crimestopper Security Products Inc.
-
Page 2: Table Of Contents
Troubleshooting: “Before you call section”………………………………………………………………...…….12 OPERATION CAUTIONS & WARNINGS CRIMESTOPPER SECURITY PRODUCTS, INC. and its VENDORS shall not be liable for any accident resulting from the use of this equipment. This system is designed to be professionally installed into a car or vehicle in good running order. -
Page 3: Operating Instructions - Alarm
OPERATING INSTRUCTIONS - ALARM Active Arming / Locking: Press button #1 (Lock symbol) on the transmitter. The System will arm and confirm with one siren chirp, one light flash, and the LED DISARM will begin to flash. Power locks will lock (if equipped). Starter UNLOCK disable circuit will turn on. - Page 4 OPERATING INSTRUCTIONS - ALARM Arming With Shock Sensor Bypass To arm the alarm and bypass shock sensor protection, press Button #1 as normal then press and release Button #1 and #2 together within 2 seconds. You will hear 3 extra siren chirps indicating shock sensor bypass for this arming cycle only.
-
Page 5: Operating Instructions - Alarm
Valet Park mode. Optional M.A.P. (Mobile Accessories Protection) This system can be programmed to provide Crimestopper’s unique M.A.P. (Mobile Accessories Protection) feature that allows you to prevent unauthorized access of your vehicles Audio, Cellular, Navigation, or Entertainment systems. This feature is OPTIONAL and will requires extra parts and labor for installation. -
Page 6: Led Diagnostics
LED DIAGNOSTICS The CS-2011RS system includes disarm diagnostics, through the RED LED light, that will help in determining what caused the last trigger of the alarm system. This is a valuable tool in determining how the vehicle was tampered with or if there is a false alarm problem in which case you can make the necessary adjustments to correct the problem. - Page 7 REMOTE ENGINE CONTROL REMOTE ENGINE STARTING - UNSUCCESSFUL START In the event that the engine does not start on the first attempt, the system shuts down for a few seconds, then attempts to restart the engine a 2 and 3 time.
- Page 8 REMOTE ENGINE CONTROL IDLE DOWN MODE - EXITING THE VEHICLE: 1) With engine running, press Remote Start button on remote transmitter. Siren will chirp 3 times for confirmation. 2) Parking Lights will turn ON. 3) Doors will unlock, or if brake pedal is being depressed doors will unlock when it is released. 4) Turn OFF Ignition and remove key.
-
Page 9: Anti-Carjack Protection
REMOTE ENGINE CONTROL TIMED SELF START MODE This mode allows the vehicle to be programmed to self-start every 4 hours and run for the programmed run time. This can be helpful during extremely cold conditions where engine fluid freeze-up is a concern. THE VEHICLE MUST BE OUTDOORS OR IN A WELL VENILATED AREA. -
Page 10: Anti-Carjack Protection
ANTI CARJACK PROTECTION SWITCH-CONTROLLED CARJACK: This configuration will enable the vehicle owner to activate a Carjack countdown by pressing a hidden push- button (not included with kit) during a Carjack situation. A Carjack countdown will begin under the following conditions: Ignition is ON (vehicle is running), the push-button is pressed, and the door opens/closes. Upon these 3 events, in that order, the alarm will start a Carjack countdown. -
Page 11: Transmitter Programming
TRANSMITTER PROGRAMMING WAIT FOR (BLUE WIRE GROUNDED) 4 FLASHES PRESS 4X's START FLASH 2, 3, or 4 X's 2 VEHICLE OPERATION A single CS2011RS III remote can control two independent vehicles with CS2011 RS III systems installed. CAR I / CAR II OPERATION SETUP: See diagram at right on how to switch your remote control to Car II operation. -
Page 12: Troubleshooting: "Before You Call Section
TROUBLESHOOTING: “BEFORE YOU CALL SECTION” Before calling your dealer or Crimestopper, read the following section for tips that may remedy or explain your problem. SYSTEM LED FLICKERS WHEN PRESSING REMOTE CONTROL BUTTONS: This is normal operation. There may be a slight flicker visible from the LED when pressing the remote as the system is authorizing the code from the remote control.