Advertisement
battery indicators. Inherent in the manufacturing process are small black spots
that appear in the optical system. These are a natural characteristic of the
LCD,cannot be fully eliminated in the manufacturing process and do not affect the
distancing performance of the unit.
• Dimensions: 2.25 x 3.5 x 4.75 inches
• Weight: 10.4 oz.
• Accuracy: +/- 1 yard
• Magnification: 4x
• Display: LCD (even and odd numbers)
• Power Source: 9 - volt alkaline battery (user supplied)
• FOV: 300 ft. @ 1000 yards
• Total Eye Relief: 25mm
• Exit Pupil: 4.2 mm
• Water resistant
• Modes: Standard & Scan
• 20-yard / 18 meters minimum, 999 yards / 913 meters to a reflective target, 700
yards / 640 meters to a tree, 300 yards / 274 meters to a flag
• Includes carrying case
CLEANING
Gently blow away any dust or debris on the lenses (or use a soft lens brush). To
remove dirt or fingerprints, clean with a soft cotton cloth, rubbing in a circular
motion. Use of a coarse cloth or unnecessary rubbing may scratch the lens
surface and eventually cause permanent damage. For a more thorough cleaning,
photographic lens tissue and photographic-type lens cleaning fluid or isopropyl
alcohol may be used. Always apply the fluid to the cleaning cloth - never directly
on the lens.
WARRANTY / REPAIR
TWO-YEAR LIMITED WARRANTY
Your Bushnell
®
product is warranted to be free of defects in materials and workmanship
for two years after the date of purchase. In the event of a defect under this warranty, we
will, at our option, repair or replace the product, provided that you return the product
postage prepaid. This warranty does not cover damages caused by misuse, improper
handling, installation, or maintenance provided by someone other than a Bushnell
Authorized
Service Department.
Any return made under this warranty must be accompanied by the items listed below:
1) A check/money order in the amount of $10.00 to cover the
cost of postage and handling
2) Name and address for product return
3) An explanation of the defect
4) Proof of Date Purchased
5) Product should be well packed in a sturdy outside shipping carton,
to prevent damage in transit, with return postage prepaid to the
address listed below:
IN U.S.A. SEND TO:
Bushnell Performance Optics
Attn.: Repairs
8500 Marshall Drive
Lenexa, Kansas 66214
For products purchased outside the United States or Canada please contact your local
dealer for applicable warranty information. In Europe you may also contact Bushnell
at: 33 141 44 94 80
Bushnell Performance Optics Service Centre
Columbusstraat 25
3165 AC Rotterdam
The Netherlands
* This warranty gives you specific legal rights.
You may have other rights which vary from country to country.
©2002 Bushnell Corporation
Before returning for repair, consult the Trouble Shooting Table.
IN CANADA SEND TO:
Bushnell Performance Optics
Attn.: Repairs
25A East Pearce Street, Unit 1
Richmond Hill, Ontario L4B 2M9
TROUBLE SHOOTING TABLE
If unit does not turn on - LCD does not illuminate:
• Depress power button.
• Check and if necessary, replace battery.
If unit powers down (display goes blank when attempting to power the laser):
• The battery is either weak or low quality. Replace the battery with a good
quality alkaline battery.
There is no reset button to clear last range reading before ranging another target:
• The last range reading does not need to be cleared before ranging another
target. Simply aim at the new target using the LCD's reticle, depress the
power button and hold until new range reading is displayed.
Target range cannot be obtained:
• Make sure LCD is illuminated.
• Make sure that the power button is being depressed (as opposed to
mode button).
• Make sure that nothing, such as your hand or finger, is blocking the objective
lenses (lenses closest to the target) that emit and receive the laser pulses.
• Make sure unit is held steady while depressing power button.
• A less reflective target will require you to scan its surface to find the most
reflective point in order to obtain a distance. To do this, hold the power button
and scan its surface to find the most reflective point in order to obtain a
distance. To do this, hold the power button and scan LCD reticle across the
target's surface to try and register a "hit" (indicated when the first square
illuminates), stabilize the unit in place and hold the power button until a
reading is displayed.
2
Advertisement
