Advertisement
Quick Links
PLEASE study these instructions carefully before beginning this installation. Most installations can be accomplished with common tools and
procedures. However, you should be familiar with and comfortable working on your vehicle. If you do not feel comfortable performing this installation,
it is recommended to have the installation completed by a qualified mechanic. If you have any questions, please call our Technical Hotline at:
1-800-416-8628, 7:00 am - 5:00 pm, Pacific Standard Time, Monday through Friday or e-mail us at Edelbrock@Edelbrock.com.
IMPORTANT NOTE: Proper installation is the responsibility of the installer. Improper installation
will void your warranty and may result in poor performance and engine or vehicle damage.
These instructions are designed to give general installation guidelines. A complete step-by-step procedure manual would require many
pages. If you are a novice or just learning to work on automotive engines, we recommend consulting either Chilton or Motors automotive manuals
before you begin. You may also contact an experienced mechanic. Please be advised that an improper installation may result in LOW MILEAGE, POOR
PERFORMANCE, COSTLY REINSTALLATION AND EVEN ENGINE DAMAGE. Installing a camshaft is a complex procedure. Please follow these
instructions carefully. Failure to do so may void your warranty.
• Before you begin the removal and installation process, please examine the kit for possible shipping damage. If the camshaft is damaged, contact
your dealer immediately. Also, make sure you have all the recommended tools and parts as listed below. As you read through these instructions
the first time, use the preparation checklist to check off the exact items you will need.
• Performer RPM camshafts are ground specifically for use with the corresponding Performer or Performer RPM manifold. They are dyno-matched
and street proven to work as a team; especially when part of an Edelbrock Total Power Package. However, a Performer RPM camshaft package
may also be used with other components designed to operate in a similar RPM range.
Tools & Equipment For Installation
❑ Box and open end wrenches
❑ Socket set
❑ Distributor wrench
❑ Pliers (channel locks & hose clamp)
❑ Screw drivers (regular and phillips)
❑ Torque wrench
❑ Hammer
❑ Gasket scraper or putty knife
❑ Timing light vacuum gauge
❑ Rags
❑ Water bucket
❑ Harmonic balancer puller
❑ Masking tape (for tagging hoses and electrical wires)
❑ Chalk , paper and pencil
❑ Crankshaft dampener puller
Catalog #2281
Rev. 4/07 - RS/mc
®
PREPARATION CHECKLIST
PERFORMER RPM HYDRAULIC ROLLER CAMSHAFT
For 351 c.i.d. (Windsor) Ford V8 Engines
Hardware & Parts To Buy
❑ Edelbrock Roller Lifters #97453, or equivalent
❑ Edelbrock Push Rods #9656 (designed for roller lifters),
or equivalent
❑ Nylon camshaft thrust button (included).
❑ Intake Gaskets - Edelbrock #7220, OEM or equivalent
❑ Pipe plugs, if needed
❑ Edelbrock Gasgacinch #9300
❑ RTV Silicone sealer
❑ Engine oil and filter
❑ Radiator coolant
❑ Adjustable, stud mounted rocker arms
❑ Edelbrock True Rolling Timing Chain Set #7811 (1984-
1995: from 3/21/84) or #7820 (1962-1984: to 3/21/84)
❑ Front cover oil seal, OEM or equivalent
❑ Valve Springs with a closed pressure of 110-120, open
pressure of 330-340 and a lift of .550"
NOTE: Edelbrock Sure Seat Valve Springs #5722
are not recommended.
Page 1 of 4
CATALOG #2281
INSTALLATION INSTRUCTIONS
©2007 Edelbrock Corporation
Brochure #63-2281
Advertisement
Related Manuals for Edelbrock 351
Summary of Contents for Edelbrock 351
-
Page 1: Installation Instructions
• Performer RPM camshafts are ground specifically for use with the corresponding Performer or Performer RPM manifold. They are dyno-matched and street proven to work as a team; especially when part of an Edelbrock Total Power Package. However, a Performer RPM camshaft package may also be used with other components designed to operate in a similar RPM range. - Page 2 Note: Edelbrock Sure Seat Valve Springs #5722 are not recommended with cast iron heads. LIFTERS: Edelbrock offers a replacement roller lifter kit, part #97453. To install new or factory roller lifters, use fresh clean oil on the lifter and the lifter bore just prior to installing. Make sure to re-install the factory guide system (if applicable).
- Page 3 40-45 ft/lbs. CAUTION: When using an Edelbrock Timing Chain and Gear Set with an Edelbrock cam, straight up timing alignment is achieved. If any other timing gear set is used, it is necessary to check camshaft position for correct timing alignment. This requires indexing the camshaft with a degree wheel to verify timing alignment.
- Page 4 3/4" in diameter, approximately 31" long, with a 3" collector should be used.. The exhaust system should consist of dual exhaust pipes, at least 2" diameter with low back-pressure mufflers such as the Edelbrock SDT Series mufflers. Please consult your Edelbrock dealer or the Edelbrock catalog for a listing of available Edelbrock SDT Mufflers.