Echo PE-200 Operator's Manual
  1. Manuals
  2. Brands
  3. Echo Manuals
  4. Edger
  5. PE-200
  6. Operator's manual

Echo PE-200 Operator's Manual

Echo power edger operator's manual
Hide thumbs Also See for PE-200:
Table of Contents

Advertisement

Quick Links

Power Edger
Operator's Manual
MODEL
Read rules for safe operation and instructions carefully. ECHO provides an
Operator's Manual and a Safety Manual. Both must be read and understood for
proper and safe operation.
X7702275300
PE-200
Serial Number 05001001 - 05045500
WARNING
DANGER
X770000680
03/03

Advertisement

Table of Contents
loading

Related Manuals for Echo PE-200

Summary of Contents for Echo PE-200

  • Page 1 Power Edger Operator's Manual MODEL Read rules for safe operation and instructions carefully. ECHO provides an Operator's Manual and a Safety Manual. Both must be read and understood for proper and safe operation. X7702275300 PE-200 Serial Number 05001001 - 05045500...

  • Page 2: Table Of Contents

    NTRODUCTION Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and on-the-job- dependability. Read and understand this manual and the SAFETY MANUAL you found in the same package. You will find both easy to use and full of helpful operations tips and SAFETY messages.

  • Page 3: Manual Safety Symbols And Important Information

    Locate these safety decals on your unit. Make sure the decals are legible and that you understand and follow the instructions on them. If a decal cannot be read, a new one can be ordered from your ECHO Dealer. See PARTS ORDERING instructions for specific information.

  • Page 4: International Symbols

    NSTRUCTIONS PERSONAL CONDITION AND SAFETY EQUIPMENT Edger users risk injury to themselves and others if the edger is used improperly and or safety precautions are not followed. Proper clothing and safety gear must be worn when operating an edger. Physical Condition Your judgment and physical dexterity may not be good: •...

  • Page 5: Extended Operation/Extreme Conditions

    Use only ECHO approved attachments. Serious injury may result from the use of a non approved attachment combination. ECHO, INC. will not be responsible for the failure of cutting devices, attachments or accessories which have not been tested and approved by ECHO. Read and comply with all safety instructions listed in this manual and safety manual.

  • Page 6: Safe Operation

    SAFE OPERATION WARNING Do not operate this product indoors or in inadequately ventilated areas. Engine exhaust contains poisonous emissions and can cause serious injury or death. Read the Manuals • Provide all operators of this equipment with the Operator's Manual and Safety Manual for instructions on safe operation.

  • Page 7: Description

    The ECHO product you purchased has been factory pre-assembled for your convenience. Due to packaging restrictions, power head and other assembly may be necessary. After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing parts. Use the contents list to check for missing parts.
  • Page 8 POWER HEAD - Factory assembled. Includes the engine, clutch, fuel system, ignition system and starter. GRIP - Rear (right hand) handle. FRONT HANDLE - The front handle can be repositioned for comfortable operation by loosening the screws and moving the handle. SHAFT DECAL (See page 3) SHAFT DECAL (See page 3) DEBRIS SHIELD/FLAP - Mounted over the cutting attachment.

  • Page 9: Specifications

    OWER DGER PERATOR ANUAL PECIFICATIONS MODEL ----------------------------------------------------- PE-200 Length ------------------------------------------------------- 1750 mm (68.9 in.) Width -------------------------------------------------------- 300 mm (11.8 in.) Height ------------------------------------------------------- 290 mm (11.4 in.) Weight (dry w/cutter head) ------------------------------- 5.38 kg (11.9 lb.) Engine Type ------------------------------------------------ Air cooled, two-stroke, single cylinder gasoline engine Bore ---------------------------------------------------------- 32.2 mm (1.27 in.)

  • Page 10: Assembly

    Loosen the two bolts (A) at drive shaft end of engine. Carefully fit drive shaft assembly to engine, making sure that inner drive shaft engages into clutch mount. NOTE Rotate the drive shaft housing until edger housing is in line with the engine. Tighten bolts (A). THROTTLE LINKAGE Place throttle linkage (B) through adjustment fixture (C) and install wire end into large carburetor throttle swivel hole (D).

  • Page 11: Pre-Operation

    IMPORTANT Echo premium Power Blend Universal 2-Stroke Oil may be mixed at 50:1 ratio for application in all Echo engines sold in the past regardless of ratio specified in those manuals. Mixing Instructions Fill an approved fuel container with half of the required amount of gasoline.

  • Page 12: Operation

    PERATION STARTING COLD ENGINE WARNING The attachment will operate immediately when the engine starts and could result in loss of control and possible serious injury. Keep movable parts of the attachment off the ground and away from objects that could become entangled or thrown. Stop Switch Move stop switch (A) away from the STOP position.

  • Page 13: Starting Warm Engine

    The attachment should not move at idle, otherwise serious personal injury may result. NOTE If attachment moves, readjust carburetor according to “Carburetor Adjustment” instructions in this manual or see your ECHO Dealer. Stop Switch Move stop switch (A) away from the STOP position Primer Pump primer bulb (C) until fuel will be visible and flows freely in the clear fuel tank return line.

  • Page 14: Operating Techniques

    Before edging, plan your direction of travel so that the unit will always be positioned on your right side and so that you walk on a hard surface whenever possible. Hold edger as shown. WARNING Before edging, be sure to read and understand the entire Operator's Manual to avoid the chance of serious injury.

  • Page 15: Maintenance

    ECHO Service Dealer for maintenance. To help you decide whether you want to DO-IT-YOURSELF or have the ECHO Dealer do it, each maintenance task has been graded. If the task is not listed, see your ECHO Dealer for repairs.

  • Page 16: Air Filter

    AIR FILTER Level 1. Tools required: Cleaning brush 25 or 50 mm (1 or 2 in.) Parts required: 90008 REPOWER Close choke (Cold Start Position). This prevents dirt from entering the carburetor throat when the air filter is removed. Brush accumulated dirt from the air cleaner area. Remove the air cleaner cover.

  • Page 17: Spark Plug

    SPARK PLUG Level 2. Tools Required: T-Wrench, Feeler gauge, Soft metal brush. Parts Required: REPOWER Tune-Up Kit P/N 90074 Remove spark plug and check for fouling, worn and rounded center electrode. Clean the plug or replace with a new one. DO NOT sand blast to clean.

  • Page 18: Exhaust System

    Remove spark plug lead from spark plug. Remove muffler cover bolt (A). Remove four screws that retain the engine cover. Two at the top of the Recoil Starter, two on either side of the front. Lift the cover from the engine and lay to the front of the engine. NOTE The spark plug lead and grommet remain in the engine cover.

  • Page 19: Carburetor Adjustment

    The cylinder exhaust port must be inspected and cleaned of excess carbon every 3 months or 90 hours of operation in order to maintain this engine within the emissions durability period. ECHO strongly recommends that you return your unit to your ECHO dealer for this important maintenance service. CARBURETOR ADJUSTMENT...

  • Page 20: Blade Replacement / Lubrication

    BLADE REPLACEMENT Level 1. Tools Required: Scrench, Locking Tool, Needle Nose Pliers, 8 mm Open End Wrench Parts Required: ECHO LUBE ® Grease, Blade P/N 69601552632 NOTE Grease gear case every 15 - 25 hours of use. Replace blade when it is worn shorter than 6 in.

  • Page 21: Troubleshooting

    ROUBLESHOOTING t l i t l i Fuel vapors are extremely flammable and may cause fire and/or explosion. Never test for ignition spark near an open spark plug opening, otherwise serious personal injury may result. l f f t l i t l i t r i t r i...

  • Page 22: Storage

    TORAGE During operation the muffler or catalytic muffler and surrounding cover become hot. Always keep exhaust area clear of flammable debris during transportation or when storing, otherwise serious property damage or personal injury may result. Long Term Storage (over 30 days) Do not store your unit for a prolonged period of time (30 days or longer) without performing protective storage mainte- nance which includes the following: Store unit in a dry, dust free place, out of the reach of children.
  • Page 23 OWER DGER PERATOR ANUAL NOTES...

  • Page 24: Servicing Information

    • Sending a check or money order for $2.00 per Parts Catalog or $1.50 per Operator's Manual made payable to ECHO, INCORPORATED. State on a sheet of paper the model number and serial number of the ECHO unit you have, part number of the manual (if known), your name and address and mail to address below.

Table of Contents