T I M E R S A N D M O D E S E L E C T I O N S S 1 & S 2; Fast Run Timer - S1; Mode Selections - S1; Close Timer - S2 - Chamberlain MEGA SLIDE-X Owner's Manual

T I M E R S A N D M O D E S E L E C T I O N S S 1 & S 2
FAST RUN TIMER - SWITCH PACK S1 (1-5)
To change the FAST SPEED run timer, set the dip switches to add
up to the number of feet, minus one foot, for the total feet of
travel across roadway.
Example: If road is 15' wide, then set dip switches to add up to
14 seconds (dips 2, 3, 4 are on) which is 2 seconds + 4 seconds
+ 8 seconds = 14 seconds. You must set FULL SPEED to end
before the end of travel and allow the gate to go to the slow
speed before stopping.
Verify that the FAST SPEED run timer setting slowed down the
gate approximately 1' from the end of travel. If it does not, adjust
the dip switches appropriately.
MODE SELECTIONS - SWITCH PACK S1 (6-8)
SWITCH 6: FAIL SECURE MODE, (VER 6.351 or higher) with ac
power off, in continuous battery back up mode (S2 #8 off) gate
will not auto open if batteries get low. If batteries are low, gate
will stay open after an open command is given.
SWITCH 7: No longer used as of August 16, 2003. To be
redefined.
SWITCH 8: Not used at this time (VER 6.34 or higher only).
CLOSE TIMER - SWITCH PACK S2 (1-5)
On the MEGA SLIDE X the switches 1-5 on S2 are for the closing
timer delay. If S2-7 is on, the gate will auto close by timer.
Default is S2-3 "on" to provide a 4 second delay if activated.
MODE SELECTIONS - SWITCH PACK S2 (6-8)
SWITCH 6: Sets auxiliary open input terminal #4 at J5 to be
pulse open--pulse close (example: residential applications).
SWITCH 7 - AUTO CLOSE TIMER: Default is OFF. When on,
use S2 1-5 to set close time delay.
When close timer is selected, YOU must install vehicle and
pedestrian detection devices. It is strongly recommended that
photoelectric beams (eyes) be installed on BOTH sides of the
slide gate to reduce the possibility of injury to persons that may
attempt to walk through gate opening. Along with the beams, it
is strongly recommended that pressure sensing edges be
installed on the leading edge of the gate panel, and any area
that presents a PINCH POINT or risk of ENTRAPMENT.
SWITCH 8 - AUTO OPEN ON AC POWER FAILURE: When
switch number 8 is in the ON position, the operator will
automatically open the gate approximately 15 seconds after the
loss of power. Once ac power is restored, the operator will
resume normal operation.
Seconds - - 1 - - 2 - - 4 - -
S1
ON
ON
OFF OFF
1 2 3 4 5 6 7 8
Fast Run Timer 1-5
1 1
J2
AUX LIMITS M/S J3
R14
D8 D1Ø
R18
R17
S1 S2
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
R16
R1 R12
U4
C2
U1
OLS
D7
OPEN
X1
R1Ø
D6
R9
BRAKE
R8
D5
U5
CLOSE
D4
R7
CLS
D3
R6
IRD
U3
D2 CPU
R5 U2
R19
R4
R3
Q1
D9 C5
D1
R2 R11
HBEAT BAT LO AC POWER
K1
D11 D12
R13
J4
U19
Aux Relay
J1 C NC NO DC
1
1
ACC+ ACC–
PWR
1 - - 2 - - 4 - -
Seconds - -
S2
ON
ON
OFF
OFF
1 2 3 4 5 6 7 8
Close Timer 1-5
13
8 - - 16
ON
OFF OFF OFF
OFF
Mode Selection 6-8
1 2 3 4 5 6 7 8 9 1Ø 11 12
MANUAL
J5
OPEN
Q2
S3 T2 T4 T6 T8
T1 T3 T5 T7
OPEN 1 OPEN 2 OPEN 3 AUX 4 SAFETY 5CLOSE 6 BACK 7SHADOW 8
CLOSE
C16
R21
R24 R35 R41 R46 R5Ø R61
C3
U8 U9 U11 U13 U14 U15
R23 R34 R4Ø R45 R49 R6Ø
R22 R33 R39 R44 R48 R59
R43
R43
R26
U6
R63
D21
U16
IRD1
R25 R58
C12
U12
U7 DX3
U1Ø
DX4
R57
C13
R56
C4
DX2
R38
JP2
R37
R51
F2 R55
D2Ø
1A DC
R2Ø WARNING FOR
C8
R62
+
C2Ø CONTINUOUS
F1
+
PROTECTION
AGAINST FIRE
DX1
REPLACE ONLY
+ F4
WITH THE SAME
B1
TYPE AND RATING
OF FUSE
F3
D14
MOTOR
BAT– MOV
TR
BAT– BAT+ 24VAC XFMR MOTOR
8 - - 16
OFF OFF OFF OFF OFF
Mode Selection 6-8
Shows
Default
Settings
Shows
Default
Settings