T & P Valve And Pipe Insulation; Temperature Pressure Relief Valve; Water Piping - Kenmore 33094 - Power Miser 9 Owner's Manual

Thiswaterheater s hallnotbe connected t o anyheating
systems orcomponent(s) used with anon-potable water heating
appliance.
Allpiping c omponents connected tothisunit f orspace heating
applications shall b esuitable f orusewithpotable water.
Toxic c hemicals, such asthose used forboiler treatment shall
notbeintroduced intothis system.
Water supply systems may, because ofsuch events a shigh line
pressure, frequent cut-offs ortheeffects ofwater h ammer, have
installed devices such aspressure reducing valves, check v alves,
back flowpreventers, etc. t ocontrol these types ofproblems.
When these devices arenotequipped withaninternal by-pass,
andnoother m easures aretaken, thedevices cause t hewater
system tobeclosed. A swater i sheated, itexpands (thermal
expansion) and closed s ystems donotallow fortheexpansion
ofheated w ater.
The water w ithin t hewater h eater tank expands asitisheated
and increases thepressure ofthewater system. Iftherelieving
point o fthewater h eater's t emperature-pressure relief v alve
is reached, thevalve willrelieve theexcess p ressure. T he
temperature-pressure
relief valve is not intended for the
constant relief of thermal expansion. This is an unacceptable
condition and must be corrected. It is recommended that any
devices installed which could create a closed system have a
by-pass and/or the system have an expansion tank to relieve the
pressure built by thermal expansion in the water system. Refer
to the Thermal Expansion section under Troubleshooting Guide
or contact local plumbing authority or local Sears Service Center
on how to control this situation.
NOTE: To protect against untimely corrosion of hot and cold
water fittings, it is strongly recommended that di-electric
unions or couplings be installed on this water heater when
connected to copper pipe.
Property Damage Hazard
• Avoid water heater damage.
, Install thermal expansion tank if necessary.
- Do not apply heat to cold water inlet.
- Contact qualified installer or Sears Service Center.
Look at the top of the water heater. The cold water inlet is
marked "COLD". Put two or three turns of Teflon tape around
the threaded end of the threaded-to-sweat coupling and
around both ends of the 314" NPT threaded nipple. Using
flexible connectors, connect the cold water pipe to the cold
water inlet of the water heater.
NOTE: This water heater is super insulated to minimize
heat loss from the tank. Further reduction in heat loss
can be accomplished by insulating the hot water lines
from the water heater.
INSTALLATION COMPLETED USING
INSTALLATION KIT
FLEXIBLE
WATER SHUTOFF
CONNECTORS VALVE
HOT WATER _ COLD WATER
THREADED TO THREADED TO
SWEAT COUPLIN SWEAT COUPLING
3/4"THREADED_3/4"THREADED
COUPLING COUPLING
DRAFT HOOD
_"TEMPERATURE-
PRESSURE
RELIEF VALVE
_"-DISCHARGE PIPE
(Do not cap or plug)
FIGURE 15,
6_
AIR
GAP
- FLOOR DRAIN
T & P Valve and Pipe insulation
Remove insulation for T & P valve and pipe connections from
carton.
Figure 15 shows the typical attachment of the water piping to
the water heater. The water heater is equipped with 3/4" NPT
water connections.
NOTE: If using copper tubing, solder tubing to an adapter
before attaching the adapter to the cold water inlet
connection. Do not solder the cold water supply line directly
to the cold water inlet. It will harm the dip tube and damage
the tank.
• Look at the top cover of the water heater. The water outlet is
marked "HOT". Put two or three turns of Teflon tape around the
threaded end of the threaded-to-sweat coupling and around
both ends of the 3/4" NPT threaded nipple. Using flexible
connectors, connect the hot water pipe to the hot water outlet
on the water heater.
TEFLON® is a registered trademark of E.I. Du Pont De Nemours and Company.
13
PiPE
iNSULATION FLUE PiPE
FIGURE 15A.
Fit pipe insulation over the incoming cold water line and the hot
water line. Make sure that the insulation is against the top cover
of the heater.