Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Dual illumiNITE XIA4225
Summary of Contents for Dual illumiNITE XIA4225
- Page 1 XIA4225 INSTALLATION/OWNER’S MANUAL 2/1-Channel Mobile Power Amplifier...
- Page 2 XIA4225 INSTALLATION Preparation Please read entire manual before installation. Due to the technical nature of amplifiers, it is highly recommended that your DUAL amplifier is installed by a professional installer or an authorized dealer. Before You Start • Disconnect negative battery terminal. Consult a qualified technician for instructions.
-
Page 3: Connection Descriptions
• Use 18-gauge or larger wire for making the connections to the illuminite terminals of DUAL illuminite speakers ONLY. Be sure to observe polarity when connecting. • Do not ground any illuminite output wires or connect any illuminite wires together. -
Page 4: Connections And Controls
XIA4225 INSTALLATION Connections and Controls Low Level Inputs High Level Inputs Input Level Control Crossover Frequency Crossover Mode Switch Bass Boost LED Indicator Ground Connection Remote Connection +12VDC Battery Connection Main Fuses illuminite Fuse Illuminite Outputs Speaker Connections... -
Page 5: Typical Wire Routing
Using an incorrect fuse could damage the amplifier. Main fuse 30 amp ATO x 2 illuminite fuse 2 amp ATO x 1 XIA4225 INSTALLATION Typical Wire Routing Power/Ground Wire Size For optimum performance, use only the wire size listed below or larger. -
Page 6: Output Connections
12VDC output including independent fused protection (2 amp) specifically for use with illuminite speakers. DUAL illuminite speakers have two distinct sets of input terminals. The first is labeled audio input terminals and the second is labeled illuminite lighting inputs. The inputs are clearly marked with a label positioned directly above the terminal housing. -
Page 7: Input Signal Connections
The minimum impedance load is 2 ohms stereo and 4 ohms bridged. Use of loads lower than these is not recommended and may cause amplifier damage. The XIA4225 can be wired for stereo, bridged or stereo/bridged simultaneous operation. Input Signal Connections Low Level Input (RCA) Low level (RCA) input signal is preferred for best performance. -
Page 8: Configuration/Setup
XIA4225 OPERATION Configuration/Setup Input level Control Crossover Mode Crossover Frequency Control Bass Boost LED Indicator The input level control (gain) is used to obtain the best possible match between the head unit audio output and the amplifier input. Begin by turning the input level control fully counterclockwise. Next, turn up the head unit volume control around 3/4 of the way up. -
Page 9: Limited One Year Warranty
This warranty gives you specific legal rights. You may also have other rights which vary from state to state. Dual Electronics Corp. warrants this product to the original purchaser to be free from defects in material and workmanship for a period of one year from the date of the original purchase. -
Page 10: Specifications
XIA4225 OPERATION Specifications Power Output: Signal to noise ratio: Additional power output: 200 Watts RMS x 2 channels at 2 ohms and < 1% THD+N 400 Watts RMS x 1 channel at 4 ohms (bridged) and < 1% THD+N Dynamic power: Speaker output impedance: illuminite output voltage: illuminite output Low level input range: High level input range: Bass boost: Crossover range: Crossover slope: Power supply:... -
Page 11: Troubleshooting
Fuse blown - illuminite output (+12VDC) wire (no lights) touching ground illuminite (+) or (-) wires not connected illuminite connections wired wrong (reverse polarity) illuminite speaker(s) defective or damaged XIA4225 OPERATION Troubleshooting Cause Check connections for proper voltage (11~16VDC) Check connection to ground Replace fuse(s) - Page 12 Dual Electronics Corp. Toll Free: 1-866-382-5476 www.dualav.com ©2006 Dual Electronics Corp. NSA0706-V01...