Table of Contents
Advertisement
Example of connections in 23.98/24/
29.97/25 Hz mode
When playing back a card recorded at a frame rate of 24 fps
(25 fps), the unit is capable of converting the output to 1080/
24 PsF (1080/25 PsF or 1080/50i) for recording on an AJ-
HD3700 series.
Shown in the figure below is an example of deck-to-deck
connections. Input the following reference signals as REF input.
AJ-HPM110
(source rear panel)
Reference signal
23.98 Hz mode: HD REF 47.95 Hz (interlace)
24 Hz mode: HD REF 48 Hz (interlace)
25 Hz (HD)/50 Hz (HD) mode: HD REF 50 Hz (interlace) or SD REF 50 Hz (interlace)
29.97 Hz mode: HD REF 59.94 Hz (interlace) or SD REF 59.94 Hz (interlace)
HD SDI OUT
HD SDI signal
AJ-HD3700B
HD
(recorder rear
REF
panel)
signal
~
AC IN
FUSE
125V 5A
REMOTE
IN
SIGNAL
GND
Ω
75
termination ON
HD REF IN
◆ NOTE:
• Synchronization with REF input at start of playback in 23.98/24 Hz
mode may distort the first number of frames and mute sound output.
Note that movement in HD SD video output at speeds other than 1x
may look unnatural.
38
Introduction: Connections
Connections
Ω
75
REMOTE IN/OUT
termination OFF
Remote
signal (9P)
SD
REMOTE
HD SDI IN
REF
IN/OUT
signal
REF IN
VIDEO OUT
WFM
SD SDI
HD SDI
HD
SD
1
2
3
IN
OUT1
IN
OUT
1
ON
ON
(SUPER)
ACTIVE
ACTIVE
75
75
THROUGH
THROUGH
OUT
C
H
C
H
INPUT
C
H
C
H
OUT2
2
OFF
OFF
SD
HD
SD
SPARE
MONITOR
C
H
C
H
OUTPUT
C
H
C
H
(SUPER)
R
E
F
O
U
T
I D
G
T I
A
L
A
U
I D
O
REMOTE
REMOTE
V/A
OUT
IN/OUT
CONTROL
CONTROL
PANEL
AUDIO IN
TIME CODE
CH 1
CH 2
CH 3
CH 4
CH 5
IN
PUSH
OUT
AUDIO OUT
MONITOR
CH 1
CH 2
CH 3
CH 4
CUE
L
R
PUSH
PUSH
PUSH
PUSH
PUSH
PUSH
PUSH
Ω
75
termination
ON
SD REF IN
Video monitor
• In 23.98 Hz mode, the composite monitor video signal output by the
ANALOG COMPOSITE MONITOR OUT connector does not include
VITC signals.
• For details on compatible input and output formats, refer to "List of
Compatible Input and Output Formats" (page 147).
• In 23.98/24/29.97/25 Hz mode, the TIME CODE OUT connector
does not output a time code and a time code cannot be input to the
TIME CODE IN connector.
• In 23.98/24 Hz mode, HD SDI output is delayed by approximately 2
frames relative to analog VIDEO output.
• In 23.98/24 Hz mode, the analog video signals are not output.
• Composite monitor video is not output in 24 Hz mode.
Example of connections for remote
control
These connections make it possible to send commands via
the remote control connector to enable remote control of
external devices.
Shown in the figure below is an example of deck-to-deck
connections.
Set the CONTROL switch on the front panel of the external
device to REMOTE.
Set the CONTROL switch on the front panel of this unit to LOCAL.
AJ-HD1400, etc.
(source rear panel)
OUT
3
MONITOR
(SUPER)
RS-232C
PARALLEL
IN/OUT
(50P)
AJ-HPM110
(recorder rear
panel)
TC
HD/SD REF IN
VIDEO OUT
1
Y
P
IN
B
HD/SDI
IN
P
R
OUT1
2
OUT
AUDIO OUT
(SUPER)
AUDIO IN
CH1
CH2
AUDIO
L
CH1
PUSH
PUSH
CH2
MON
OUT2
OUT
DC OUT
12V 250mA
SD/SDI
R
R
PUSH
PUSH
E
FUSE 250V T2.5AH
M
F1
O
T
DVCPRO
ENCODER
E
/DV
REMOTE
L
R
MONITOR
AC IN
SIGNAL
GND
DC IN
Advertisement
Table of Contents
