Appendix; Power Cables; Charging The Device; About Device Care - Garmin zumo 350LM Owner's Manual

3 Select > Restore.

Appendix

Power Cables

Your device can be powered four ways.
• Motorcycle power cable
• Vehicle power cable
• USB cable
• AC adapter (optional accessory)

Charging the Device

You can charge the battery in the device using any of these
methods:
• Connect the device to the vehicle power cable.
• Connect the device to the motorcycle power cable.
• Connect the device to a computer using the included USB
cable.
• Connect the device to an optional power adapter accessory,
such as a wall power adapter.

About Device Care

Avoid dropping your device.
Do not store the device where prolonged exposure to extreme
temperatures can occur, because it can cause permanent
damage.
Never use a hard or sharp object to operate the touchscreen, or
damage may result.

Cleaning the Outer Casing

1 Clean the outer casing of the device (not the touchscreen)
using a cloth dampened with a mild detergent solution.
2
Wipe the device dry.

Cleaning the Touchscreen

1
Use a soft, clean, lint-free cloth.
2 If necessary, use water, isopropyl alcohol, or eyeglass lens
cleaner.
3
Apply the liquid to the cloth.
4
Gently wipe the screen with the cloth.

Avoiding Theft

• Remove the device and mount from sight when not in use.
• Remove the residue left on the windshield by the suction
cup.
• Do not keep your unit in the glove compartment.
• Register your device at http://my.garmin.com.
Extending the Battery Life
• Keep your device away from extreme temperatures.
• Put the device in sleep mode
• Decrease the screen brightness
• Do not leave your device in direct sunlight.
• Decrease the volume (page
• Disable Bluetooth (page
• Shorten the display timeout time
Appendix
NOTICE
NOTICE
NOTICE
(page 3).
(page 14).
3).
14).
(page 14).
Changing the Fuse in the Vehicle Power
Cable
When replacing the fuse, do not lose any of the small pieces
and make sure they are put back in the proper position. The
vehicle power cable does not work unless it is assembled
correctly.
If your device does not charge in your vehicle, you may need to
replace the fuse located at the tip of the vehicle adapter.
1
Unscrew the end piece
TIP: You may need to use a coin to remove the end piece.
2
Remove the end piece, the silver tip
3
Install a 2 A fast-blow fuse.
4
Place the silver tip in the end piece.
5
Screw the end piece back into the vehicle power cable

Mounting on Your Dashboard

The permanent mounting adhesive is extremely difficult to
remove after it is installed.
Use the mounting disk to mount your device to the dashboard
and comply with certain state regulations. See
for more information.
1 Clean and dry the dashboard where you are placing the disk.
2
Remove the backing from the adhesive on the bottom of the
disk.
3
Place the disk on the dashboard.
4
Remove the clear plastic cover from the top of the disk.
5 Place the suction cup mount on top of the disk.
6
Flip the lever down (toward the disk).

Removing the Device, Cradle, and Mount

Removing the Device from the Cradle

1
Press the tab on the top of the cradle.
2
Tilt the device forward.

Removing the Cradle from the Mount

1
Turn the cradle to the right or left.
2
Apply pressure until the socket on the cradle releases the
ball on the mount.
Removing the Suction Cup Mount from the
Windshield
1
Flip the lever on the suction cup mount toward you.
2 Pull the tab on the suction cup toward you.

Updating Maps

1 Open myDashboard (page
2
Register the device (page
3
Select an option.
• Under Map Updates, click Update Now.
• If a free map update is no longer available, click Buy
Now.
4
Follow the on-screen instructions.
NOTICE
.
, and the fuse
NOTICE
www.garmin.com
3).
3).
.
.
15