Onkyo HT-RC470 Instruction Manual page 60

■
Film Mode
*2*4
Video:
"Film Mode" detection is not applied and the input
signal is handled as a video source.
Auto:
Detects whether the input signal is a video or a
movie. If it is a movie, the appropriate conversion is
applied.
The AV receiver will adjust to the picture source,
automatically converting it to the appropriate progressive
signal and reproducing the natural quality of the original
picture.
■
Edge Enhancement
*2*4*5
Off
Low
Mid
High
With this setting, you can make the picture appear sharper.
■
Noise Reduction
*2*4*5
Off
Low
Mid
High
With this setting, you can reduce noise appearing on the
screen. Select the desired level.
■
Brightness
*1*2*4
–50 to 0 to +50
With this setting, you can adjust the picture brightness.
"–50" is the darkest. "+50" is the brightest.
■
Contrast
*1*2*4
–50 to 0 to +50
With this setting, you can adjust contrast. "–50" is the
least. "+50" is the greatest.
■
Hue
*1*2*4
–50 to 0 to +50
With this setting, you can adjust the color hue between
"–50" and "+50".
■
Saturation
*1*2*4
–50 to 0 to +50
With this setting, you can adjust saturation. "–50" is the
weakest color. "+50" is the strongest color.
■
Color Temperature
*2*4
Warm
Normal
Cool
With this setting, you can adjust the color temperature.
Note
cannot be used when:
• "Picture Adjust"
– The NET input selector is selected, or
– "Monitor Out" is set to "Sub".
*1 This procedure can also be performed on the remote controller
by using the Quick Setup (➔ page 45).
*2
When the "Picture Mode" setting is set to anything other than
"Custom", this setting cannot be used.
*3 If the "Resolution" setting is set to "4K Upscaling"
(➔ page 50), this setting is fixed at "Off".
*4 Press CLR if you want to reset to the default value.
*5 If the "Game Mode" setting is set to "On", this setting is fixed
at "Off".
*6
When a 3D video source is input, "Wide Mode" is fixed to
"Full".
*7 When "Metadata Compatible" is enabled, "Picture Mode" is
fixed to "Direct" (➔ page 54).
En-60
Advanced Operations
Audio Selector
■
Audio Selector
ARC:
The audio signal from your TV tuner can be sent to
HDMI OUT MAIN of the AV receiver.
With this selection, the TV's audio can be
automatically selected as a priority among other
assignments.
HDMI:
This can be selected when HDMI IN has been
assigned as an input source. If both HDMI (HDMI
IN) and digital audio inputs (COAXIAL IN or
OPTICAL IN) have been assigned, HDMI input is
automatically selected as a priority.
COAXIAL:
This can be selected when COAXIAL IN has been
assigned as an input source. If both coaxial and
HDMI inputs have been assigned, coaxial input is
automatically selected as a priority.
OPTICAL:
This can be selected when OPTICAL IN has been
assigned as an input source. If both optical and HDMI
inputs have been assigned, optical input is
automatically selected as a priority.
Analog:
The AV receiver always outputs analog signals.
You can set priorities of audio output when there are both
digital and analog inputs.
Note
• This setting can be made only for an input source that is assigned
to HDMI IN, COAXIAL IN, or OPTICAL IN.
• This setting cannot be used with the NET and USB input
selectors.
• When using the Whole House Mode, "Audio Selector" is fixed
to "Analog".
*1 You can select "ARC" if you select the TV/CD input selector.
But you cannot if you've selected "Off" in the "Audio Return
Channel" setting (➔ page 64).
*1