About Status Messages - Pioneer SC-LX85 Operating Instructions Manual

14 Additional information
In the receiver's IP settings, set DHCP
to ON. After the setting is completed,
turn the receiver's power off. Next, turn
the receiver's power back on and check
whether the wireless LAN converter's
settings can be displayed with the
receiver.
If the settings can be displayed,
change the IP address settings of the
receiver and wireless LAN converter as
necessary.
The IP address settings of the receiver and
wireless LAN converter do not match the
settings of the wireless LAN router, etc.
! Check the IP address settings of the
receiver and wireless LAN converter
(including the DHCP setting).
If the receiver's DHCP setting is "ON",
turn the receiver's power off, then turn
the power back on.
Check that the IP addresses of the
receiver and wireless LAN converter
match the settings of the wireless LAN
router, etc.
If the receiver's DHCP setting is "OFF",
set an IP address matching the network
of the base unit (wireless LAN router,
etc.).
For example, if the wireless LAN router's
IP address is "192.168.1.1", set the
receiver's IP address to "192.168.1.XXX"
(*1), the subnet mask to "255.255.255.0",
the gateway and DNS to "192.168.1.1".
Next, set the wireless LAN converter's IP
address to "192.168.1.249" (*2).
(*1) Set the "XXX" in "192.168.1.XXX" to
a number between 2 and 248 that is not
assigned to other devices.
(*2) Set the "249" in "192.168.1.249" to
a number between 2 and 249 that is not
assigned to other devices.
104
En
Try making the wireless LAN converter's
advanced settings.
! The wireless LAN converter can be
connected to a computer to make the
advanced wireless LAN settings. For
details, see the CD-ROM included for
the wireless LAN converter. Check the
settings of the wireless LAN router, etc.,
then change the settings of the wireless
LAN converter.
Note, however, that making the
advanced wireless LAN settings will not
necessarily improve the wireless LAN
environment. Be careful when changing
the settings.
The access point is set to conceal the SSID.
! In this case, the SSID may not be dis-
played on the access point list screen.
If not, set the SSID, etc., by making the
wireless LAN converter settings on the
receiver manually.
The access point's security settings use
WEP 152-bit length code key or shared key
authentication.
! The receiver does not support WEP
152-bit length code key or shared key
authentication.
Network connections cannot be established
even when the above measures are taken.
! Reset the wireless LAN converter. After
this, redo the wireless LAN converter's
settings.
About resetting
1. Check that the wireless LAN convert-
er's power is on.
2. Press the wireless LAN converter's
reset button for at least 3 seconds.
3. Release the reset button.
When the wireless LAN converter is
restarted, the resetting procedure is
completed.

About status messages

Refer to the following information when you come up with a status message while operating the
Home Media Gallery.
Status messages
A component on the network, including a PC, is currently being connected.
STARTING H.M.G.
Wait for a while.
Connection Down The selected category or Internet radio station cannot be accessed.
File Format Error Cannot be played back for some reasons.
Track Not Found The selected song has not been found anywhere on the network.
Server Error The selected server cannot be accessed.
The server has been disconnected.
Server Disconnected
empty There are no files stored in the selected folder.
Preset Not Stored The selected Internet radio station is not currently registered and saved.
The value entered is beyond the permitted range of the network settings.
Out of Range
License Error The license for the contents to be played back is invalid.
This is displayed when the file you have attempted to register in the Favorites
Item Already Exists
folder has already been registered.
This is displayed when you have attempted to register a file in the Favorites
Favorite List Full
folder but the Favorites folder is already full.
Descriptions