Kenmore 4101 - Elite 30 in. Slide-In Electric Range Installation Instructions Manual

30" dual fuel slide-in range
Hide thumbs Also See for 4101 - Elite 30 in. Slide-In Electric Range:

Advertisement

Available languages

Available languages

iNSTALLATiON AND SERVICE MUST BE PERFORMED BY A QUALIFIED iNSTALLER.
IMPORTANT: SAVE FOR LOCAL ELECTRICALINSPECTOR'S USE.
READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
m
Q
Q
Q
Q
if the information
in this manual is not followed
exactly, a fire or explosion
may result causing property
damage, personal
injury or death.
FOR YOUR SAFETY:
--
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any
other appliance.
WHAT TO DO IF YOU SMELL GAS:
Do not try to light any appliance.
Do not touch any electrkal
switch;
do not use any phone in your building.
Immediately
call your gas supplier
from a neighbor's
phone.
Follow the gas supplier's
instructions.
If you cannot reach your gas supplier,
call the fire department.
Installation
and service must be performed
by a qualified
installer, service agency or the gas supplier.
For existing 29" (73.7 cm) cutout
width opening,
you must call the
Sears Service Center for optional
thinner side panels. Also you must
prepare the countertop
edge as
shown in the "Countertop
Preparation"
section (see page 7).
Shave
Raised
Edge
to Clear
Space
fora
31Y2"
(81 cm) Wide
Cooktop.
1 1/2" Max
(3.8 cm Max
These
surfaces
should
be flat
&
leveled
(hatched_
area).
112" Mi
5" Vlin.
Sides
30" Min.
(76.2 cm Min.
30" Min. (76.2
18" Min.
(45.7 cm) Min.
it
(33 cm)
Locate
Cabinet
Doors
1" (2.5 cm) Min. from
Cutout
Opening.
IM PORTANT:
Cabinet
and
countertop
width
should
match
the
cutout
width.
_ .................................................................
i[ ...................................................................
24" Min.
I
(61 cm Min.)
Grounded
Jonction
Box or Wall Outlet
Should Be Located 8" to 17" (20.3 cm
to 43.2 cm) From Right Cabinet and 2"
to 4" (5.1 cm to 10.2 cm) From Floor.
Do not install
the unit
in the cabinet
before
reading
next two
pages.
A. HE!GHT
I
B.WIDTH.
(:,COOKFOp
[:);DEPTH
TO
E: CUTOUT W!DTH ***
I:.CUTOUT
HEIGHT
G:
I
!
WIDTH
. FRONT OF RANGE (C0untert0p and Cabine!
DEPTH
.
OF COUNTERTOP
35 5/8"
(90.5cm)-
30" (76,2
cm)
311/2 '' (80cm)
28 5/16"
(71,9
cm)
30_+1/16"
21 3/4"
(55,2
cm) Min.
36 5/8" (93cm)
Max.
36 5/8"
(93 cm)
(76,2_+0,15
cm)
22 1/8"
(56,2
cm) Max
35 5/8"
(90.5
cm) Min.
24" (61 cm) Min. with
backguard
NOTE:Wiring diagram for these appliances are enclosed in this booklet.
P/N 318201670 (0711) Rev.
Printed
in United
States
English-
pages
1-13
Espahol-
p_iginas 14-27
Wiring
Diagrams
- pages
28

Advertisement

Table of Contents
loading

Summary of Contents for Kenmore 4101 - Elite 30 in. Slide-In Electric Range

  • Page 1 iNSTALLATiON AND SERVICE MUST BE PERFORMED BY A QUALIFIED iNSTALLER. IMPORTANT: SAVE FOR LOCAL ELECTRICALINSPECTOR'S USE. READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. if the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or death.
  • Page 2: Side Panel

    NOTES: _1 Do not pinch the power supply cord between the range and the wall. Do not seal the range to the side cabinets. 24" (61 cm) minimum clearance between the cooktop and the bottom of the cabinet when the bottom of wood or metal cabinet is protected by not less than !/4"...
  • Page 3 To avoid breakage: Do NOT handle manipulate the unit by the cooktop glass. The counter-top around the cut-out should be flat and leveled (see hatched area on illustration Before installing the unit, measure the heights of the two (2) cabinet sides (H1-4), front and back (see illustration 1) from the floor to the top of the counter.
  • Page 4 • Make sure the wall coverings around the range Important Notes to the Installer can withstand the heat generated by the range, Read all instructions contained in these installation Before installing the range in an area covered instructions before installing range. with linoleum or any other synthetic floor...
  • Page 5: Electrical Connection

    SNPower Supply Cord Kit Risk of fire or electrical shock exists if The user is responsible for connecting the power supply the incorrect amperage cord is used, the cord to the connection block located behind the back Installation instructions are not followed, or the panel access cover.
  • Page 6 2. Remove t he3 loose nuts(afteryouremove the 5. Connect the neutral of the copper power supply cord rubber band) ontheterminal b lockusinga3/8" nut to the center silver-colored terminal of the terminal driverorsocket. block, and connect the other wires to the outer Connect the neutral white wire of the copper power terminals.
  • Page 7: Cabinet Construction

    Cable from Countertop Preparation Residence White Wire range The cooktop sides of the fit over the cutout edge of your countertop. (Neutral) /""-7 Black W,res- • If you have a square finish (flat) countertop, no countertop preparation is required. Cooktop sides lay directly on edge of countertop.
  • Page 8: Installation

    • iJ Gas Supply- Installation Manual GAS FLOW Pressure When shipped from the factory, this unit is designed to Shutoff Flare Flare Regulator operate on 4"(10,16 cm) water column (1.0 kPa) Natural Valve Union Union gas manifold pressure. A convertible pressure regulator is connected to the range manifold and MUST be connected in series with the gas supply line.
  • Page 9: Gas Conversion

    Moving the Appliance Once regulator i sin place, o penthe shutoffvalve in the gassupply line.Waita few minutes f or gasto move Servicing and Cleaning through thegasline. Turn off the range line fuse or circuit breakers at the main Leaktesting of the applianceshallbe conducted power source, and turn off the manual gas shut-off valve.
  • Page 10: Range Installation

    Position range in front of the cabinet opening. Range Installation Important Note: Door removal is not a requirement for Make sure that the glass which overhangs installation of the range, but is an added convenience. countertop clears the countertop. If necessary, raise Refer to the Use and Care Guide for oven door removal the unit by lowering the leveling legs.
  • Page 11: Leveling The Range

    Decorative Rear Trim Installation Leveling the Range - Level the range after installation in the cutout opening. required) 1. Open the range drawer. The leveling screws control Disconnect the power from the range. the height of the rear leg. Make sure the range is leveled. 2.
  • Page 12 5. Operation of OvenElements The ovenisequipped w ithanelectronic o ven control. E ach ofthefunctions h asbeen factory checked b efore shipping. However, it issuggested thatyouverify theoperation o f theelectronic ovencontrols o ncemore. R efer t othe Electronic Oven Control G uide foroperation. Follow the instructions fortheClock, T imer, B ake, Broil, C onvection (some models) andClean functions.
  • Page 13: Brackets Installation

    The anti-tip bracket attaches to the floor at the back of Anti-Tip Brackets Installation the range to hold range rear center leg. When fastening instructions bracket to the floor, be sure that screws do not To reduce the risk of tipping of the range, penetrate electrical wiring or plumbing.
  • Page 14 LA INSTALACION Y EL SERVICIO DEBEN SER EFECTUADOS POR UN INSTALADOR CAUFICADO. IMPORTANTE: GUARDE ESTAS INSTRUCCIONES PARA USO DEL INSPECTOR LOCAL DE ELECTRICIDAD. LEA Y GUARDE ESTAS INSTRUCCIONES PARA REFERENCIA FUTURA. Si la informacion contenida en este manual no es seguida exactamente, puede ocurrir un incendio o explosion causando da_os materiales,...
  • Page 15 NOTAS" No pellizque el cordon electrico entre la estufa y la pared. No selle la estufa a los armarios de lado. Un espacio minimo de 24" (61 cm) entre la superficie de la estufa y el fondo del armario esto cuando el fondo del armario de madera o metal est,1 protegido por no menos de 1/4"...
  • Page 16 Para evitar fractura de la unidad: NO manipule ia unidad sosteniendo la cubierta de vidrio. La cubierta alrededor del espacio donde usted instalara su unidad debe de estar plana y nivelada. (Vea el _irea sombreada en la ilustracion n0mero 1) Antes de instalar la unidad, mida la altura de los dos (2)lados de los gabinetes (H1-4), frente y parte trasera (vea ilustraci0n 1) del piso a Io alto de la cubierta.
  • Page 17 • Antes de instaiar ia estufa en un _rea cuyo piso Notas importantes para el instalador: este recubierto con linOleo u otto tipo de piso 1. Lea todas las instrucciones de instalaciOn antes de sintetico, asegurese de que estos puedan resistir realizar la instalaciSn de la plancha de cocinar.
  • Page 18 Juego de Cordon Eiectrico Tabla de tama_o de abertura de conexi6n de codna El consumidor tiene la responsabilidad de conectar Referirse a la tabla de arriba para el tamaflo de abertura cordon electrico al bloque de conexion ubicado detr_is de connexion de cocina adecuada, y la informaciOn sobre el regimen la cubierta de acceso del panel trasero.
  • Page 19 Conexi6n de tres alarnbres de conducci6n Conexi6n de 4 alarnbres de conducci6n a ia ia estufa estufa (casas moviles) (Un cord6n flexible o cable de 3 conductores debe de set 1. Quite los tres tornillos en la parte m_is baja del panel reemplazado con un cord6n flexible o cable de 4 conducto- trasero,...
  • Page 20 Conexion electrica directa ai cortadrcuito, Donde los codigos locales NO permitan conectar el conductor de puesta a tierra del el_ctrodomestico ia caja de fusibles o ia caja de empaimes neutral (blanco), o si est_ conectado con un sistema a 4 Si el aparato est_q conectado directamente al cortacircuito, alambres (vea figura 6): a la caja de fusibles o a la caja de empalmes, use un...
  • Page 21 Construcci6n del armario Para eliminar el riesgo de quemaduras o de fuego tratando de alcanzar algo por encima de las zonas calientes, evite de colocar articulos sobre la cocina. Si cree necesitar este espacio, el riesgo puede disminuir si instala un sombrerete que proteja horizontalmente un minimo de 5"...
  • Page 22 Insta[ad6n de [a a[imentad6n de gas Valvula de FLUJO DEL GAS Regulador Fsta unidad ha sido ajustada para operar con un m01tiple de presi6n de admision para gas natural de 4"(10,16 cm) (1.0 kPa). cierre Uni6n Uni6n manual Un regulador de presion convertible esta conectado...
  • Page 23 Unavezqueregulador e st_q ensulugar,abralawilvula La mudanza del aparato para enlalineadelsuministrodegas. E sperealgunos reparaciones o [impieza minutos paraqueel gaspuedamoverse a trav_s dela lineadegas. Apague la corriente electrica a la estufa a la fuente de poder principal, y apague la wilvula de cierre manual de Paraverificarsi hayfugasen el electrodornestico gas.
  • Page 24 Instalacion de la estufa AsegOrese de que el vidrio que est,1 colgado sobre la cubierta deje despejada la cubierta. Si es necesario, levante la unidad bajando las patas de nivelaci6n. Nota importante: No es necesario, pero si es conveniente, quitar la puerta para instalar el horno. Consulte las instrucciones para retirar la puerta en la Guia Nivele la codna (vea Nivelaci0n de la estufa).
  • Page 25 Nive[ad6n de [a estufa Coloque la parte superior del accesorio decorativo debajo de esa linea. Nive[e [a codna despues de haber[a insta[ado en [a Utilizando los tornillos provistos con este juego, fije el abertura de[ mostrador. accesorio decorativo a la pared. 1.
  • Page 26 El homo est,1 equipado con un control electronico. Cada 1. Desembale las basas de los quemadores y las tapas funcion ha sido probada en la f_ibrica antes del transporte. de los quemadores. Sin embargo, sugerimos que Ud. verifique 2. Coloque una basa de quemador sobre cada abertura funcionamiento...
  • Page 27 Instrucciones de instalaci6n de la Dibujar una linea central en el piso donde se instalar_ la cocina. Si no hay pared posterior, dibujar otra linea fijacion anti-inclinacion en el piso que corresponda a la parte posterior de la cocina. Para reducir el riesgo de Desplegar el molde de papel y colocarlo alisado sobre inclinaci6n de la cocina, @stadebe ser asegurada hacia el el piso con el v#rtice posterior derecho posicionado...
  • Page 28 COLOR COOE/CODIGOS COLOR/CODE COULEUR OVEN CIRCUIT CIRCUITO DE HORNO CIRCUIT DU FOUR G.-GREEN/VERDE/VERT W.-WHITE/BLANCO/BLANO R.*RED/ROJO/ROUGE O.*ORANGE/NARANJA/ORANGE Y.*YELLOW/AMARILLO/JAUNE ELECTRONIC OVEN CONTROL/CONTROL HORMO ELECTROMICO/ BR.-BROWN/MOREMO/BRUN COMMANDE FOUR ELEOTRONtOUE BL.-BLUE/AZUL/BLEU BK.-B1ACK/NEGRO/NOIR TERMINAL BLOCK THERMAL CIRCUIT BREAKER i BLOQUE CONEXION INTERRUPTOR CIRCUITO • BLOC DE CONNECTION CODE GAUGE...

This manual is also suitable for:

4104 - elite 30 in. slide-in dual fuel range4101 30

Table of Contents