The Default Setting Menu - Toshiba TDP-T355 Owner's Manual

Using the menus (Continued)

The default setting menu

This menu shows placement status and other settings.
Item
Projection
Sets projection mode in accordance with Placement Style.
mode (Standard)
Blackboard When projecting on a non-screen surface, select a color in
mode accordance with the projecting surface.
Press and switch with
No signal Set the time to wait for the power to be turned off after the last
power off operation is made with no input signal.
Press and switch with
Off (not turned off)/1 min./5 min./10 min./30 min./60 min.
Auto input Set whether the input with signals is only selected or not.
search
Power on Sets whether to turn on the power when the ON/STANDBY button is pressed
(Manual), or when the main power switch is turned on (Auto). Manual
Lamp power
Sets the lamp power.
Fan mode Sets the cooling fan speed.
Remote control When two or more projectors are used and controlled by the remote
control respectively, this menu sets the code for the projector and the
remote control.
[ or : Enter setting mode]
Select from 1, 2, 3, 4]
Press [Cancel] to return.
Key lock Lock the control panel buttons.
[ or : Enter setting mode]
Select On/Off] [
Press [Cancel] to return.
Reset all Press . (The password and user logo are not reset.)
Resets all adjustments and settings to their factory settings.
Password Password function
p.36
When [Password] is [On], the Password Setting screen is displayed.
Detailed description
[Blackboard mode]
Projects the image in colors more like projecting on a screen.
Note
• The projected image may differ depending on
the type, color, and material of the blackboard
and wall even if the selected color is the same
as the projected screen.
[Auto input search]
[On]: Automatically searches the signals that can
be projected, and switches input from the
connected device that outputs the signals
each time the INPUT button is pressed. The
input from the connected device that outputs
no signals is skipped.
Description
p.22
(Rear) (Ceiling) (Rear ceiling)
and . Off/Green/Black/Brown/Blue/Beige
and .
On Off
Auto
Low Standard
Standard High
[ : Select item] [ :
[ :Confirm] [ :Select OK to end]
[ : Select item] [ :
:Confirm] [ :Select OK to end]
Yes No
Off On
Input select menu
Input select
Computer (1) (Digital)
Y/P /P (1) (Digital)
B R
Computer (1) (Analog)
Y/P /P (1) (Analog)
B R
Computer (2)
Y/P /P (2)
B R
Computer (3)
Y/P /P (3)
B R
Video
S-video
/ shows whether signal is
input or not.
44
[Off]: Displays the Input select menu.
Toggle with buttons and press
can be selected.)
[Power on]
Note that if [Power on] is set to [Auto], then if the main power switch is ON when
power is restored after a power outage, the projector will come on.
[Lamp power]
When [Lamp power] is set to [Low], the screen becomes a little darker, but the
cooling fan noise gets quieter.
Notes
• The lamp power selection that you made will not be switched in about 1 minute
after the power is on.
• For lamp protection, even it has been set to [Low], the lamp power mode stays in
[Standard] in about 1 minute after the power is on, and then it will be switched to
your desired selection mode.
[Fan mode]
Setting [Fan mode] to [High] increases the cooling fan speed. Set this option to
use the projector, for example, at high altitude (over 1,500 meters above sea level).
[Remote control]
Sets a remote control code from 4 types. You can set each code respectively for up
to 4 projectors. The factory setting is [1].
To switch codes, set the same code for the projector and the remote control.
A remote control code is applied after the setting is done.
• You cannot operate the remote control if the codes of the projector and the
remote control do not match.
Remote control code setting for remote control
Remove the battery cover and set the same remote control code switch as the
projector. p.16 (Use a screwdriver with thin tip to set.)
[Key lock]
Protect from operating errors by locking on the control panel buttons of the
projector. (The remote control operations are available.)
Control panel operations are locked after the setting is done.
• To release the key lock, press the control panel's RETURN button for 10 seconds.
The key lock is released with a beep sound.
45
button. (The input without signals