Operation - Denon PMA-2000IVR Operating Instructions Manual

3 OPERATION

(Refer to page 4 and 6)
PREPARATION
1. CHECKING CONNECTIONS
• Make sure that all the connections are proper by referring to
the rear panel.
• Check the polarity (positive and negative) of connections,
and the directivity of stereo separation (right cord to right
channel terminal, and left cord to left channel terminal).
• Check the directivity of pin cord connection.
2. SETTING OF EACH KNOB
• Turn the volume control knob
minimum position.
r t
• Set the rotary knob ,
!0
• Set SOURCE DIRECT
After checking the above items, turn on the power, the amplifier
is set in the ready mode in a few seconds.
PLAYING A RECORD
1. Set the CARTRIDGE selection switch
( £ )".
2. Set the INPUT SELECTOR switch
3. Operate the turntable and play the record.
u
4. Turn the volume and tone controls
appropriate volume and sound quality.
PLAYING CD PLAYER
1. Set the INPUT SELECTOR switch
2. Operate the CD player.
u
3. Turn the volume and tone controls
appropriate volume and sound quality.
RECEPTION OF RADIO PROGRAMS
1. Set the INPUT SELECTOR switch
2. Operate the tuner to receive a radio program.
u
3. Turn the volume and tone controls
appropriate volume and sound quality.
PLAYING AUDIO EQUIPMENT CONNECTED TO AUX
TERMINALS
1. Set the INPUT SELECTOR switch
P. DIRECT) position.
2. Operate the Audio equipment Systems.
u
3. Turn the volume and tone controls
appropriate volume and sound quality.
NOTE:
If power amp direct switch (BACK PANEL) is set to ON
position, power amp direct terminal is selected when AUX-
2/P. DIRECT is selected. (see
PLAY BACK WITH TAPE DECK
1. Set the INPUT SELECTOR switch
"TAPE-2/MD".
2. Operate the Tape Deck.
u
3. Turn the volume and tone controls
appropriate volume and sound quality.
u
counterclockwise, to
y
, to center position.
to "OFF ( £ )".
@1
"MC ( )" or "MM
¢
o
to "PHONO".
r t y
, , to yield an
o
to "CD".
r t y
, , to yield an
o
to "TUNER".
r t y
, , to yield an
o
to "DVD/AUX-1" (AUX-2/
r t y
, , to yield an
o
, page 5)
o
to "TAPE-1/CD-R" or
r t y
, , to yield an
RECORDING WITH TAPE DECK
1. Set the REC OUT SELECTOR switch
source you wish to record.
2. Play back the program source.
3. Start recording with the component connected to "TAPE-
1/CD-R" or "TAPE-2/MD".
• In the PMA-2000IVR, the REC OUT signal and the speaker
(headphone) signal are output via separate circuits so that
knobs and switches related to the tone and volume have no
effect what ever on the sound that is recorded. Also, since the
recording function is selected by the REC OUT SELECTOR
i
switch , the free program source can be played through the
speakers (or headphones) even during recording.
• MONITORING THE RECORDING
A recording in progress can be monitored if a tape deck with
three individual heads for recording and playback is used. A
tape deck in which a common head is used for both recording
and playback cannot be used to monitor recording. When a
recording is being made using TAPE-1/CD-R, selecting TAPE-
1/CD-R with the INPUT SELECTOR will engage the
RECORDING MONITOR and pemit a check of the recording
condition.
COPYING FROM ONE TAPE TO ANOTHER
To copy from TAPE-1/CD-R to TAPE-2/MD, set the REC OUT
i
SELECTOR switch to "TAPE-1 1 2".
NOTE:
Copying is not possible from TAPE-2/MD to TAPE-1/CD-R.
NOTE:
• This amplifier has a full memory back-up system. When the
power is turned on, INPUT SELECTOR
mode set before the power was turned off.
i
to the program
o
are set to the last
9