PITSOS DGS5512 - annexe 2 Instructions page 2

Maintenance and care
Filters ... Rotate filter
cylinder, remove
check, if
filter system ...
required clean
Spray arms ... pull lower arm
upwards ...
Remove
blockages/deposits
Rectifying minor faults yourself ...
Fault Possible causes
Display " " display is lit Supply fitting jammed or calcified
Display "E:24" Waste water hose is blocked
or kinked
and " " is lit
Cover not attached to waste
water pump
Display "E:25" Waste water pump blocked
and " " is lit
Other fault display "E:XX" Appliance has technical defect
is lit
Residual water The programme has not yet
in the appliance ended
Cutlery not rust-resistant. Hard knife
Rust on the cutlery blades are more susceptible
Extraneous rust
Terminating the programme ...
While the programme is running,
press the START button for
approx. 3 sec. (Reset).
For perfect rinsing results ...
rinse under
running water ...
unscrew
upper arm ...
... as it is worth doing it yourself!
Remedial action
Open supply fitting.
1. Unscrew water connection.
2. Clean filter in the water connection.
3. Flow rate must be min. 10 l/min. when
water supply is open. If the flow rate
is less, replace the supply fitting.
Install supply hose without kinks.
Install waste water hose without kinks.
Attach cover (see above).
Clean waste-water pump (see above).
Call factory customer service
(state fault display).
Unplug appliance.
Close and switch on the appliance or
terminate the programme
(see Terminating the programme).
Use dishwasher-proof cutlery.
Never wash rusting parts
in the appliance.
The numerical display
indicates "0:01"
Switching off the appliance
approx. 1 minute after
the programme ends,
0:00 is indicated
insert ...
insert lower arm ...
clean spray nozzles
under running water
(if required use
toothpicks) ...
Fault Possible causes
Utensils are not clean Utensils are situated close together or
one above the other
Sand or gritty residue on the Too little detergent
utensils
Unsuitable programme selected
Spray arm nozzles blocked
Filters dirty, not seated firmly
Spray arms blocked
Stains and streaks Rinse-aid dosage too high/too low
Milky deposits on the Water softening system incorrectly set;
utensils (can be removed)
No salt
Milky deposits, glasses Glasses not dishwasher-proof.
cloudy/tarnished
(cannot be removed)
Too little detergent.
Plastic/utensils discoloured
Discoloration caused by food colourings
(tomato sauce)
Loading the dishwasher correctly ...
Dishwasher-proof utensils (not soiled with ash, wax, lubricating grease, ink or adhesive labels; remove
large remnants of jam, milk products and food according to the operating instructions and check that the
spray arms can rotate freely.
Cleaning waste water pump
– Pull out the mains plug
Screw on filter
– Remove filters and scoop out water
system NOTE
– Lever off cover (––>A)
MARK!
– Check area around the fan impeller
for foreign objects
– Click cover shut (––>B)
– Insert filters
A B
screw on upper arm
tightly
Remedial action
Separate the utensils, prevent contact
points.
Follow manufacturer's instructions
(detergent).
Select a more intensive programme.
Clean the spray arms (see above).
Clean the filters (see above).
Arrange the utensils so that the spray
arms can rotate freely.
Streaks: reduce dosage.
Water or limescale stains: increase
dosage.
Correctly set water softening system.
Refill with salt.
Use dishwasher-proof glasses.
Use a detergent suitable for glasses.
Follow manufacturer's instructions
(detergent).
Discoloration is harmless; subsequent
rinse cycles will cause it to fade.
More information can be found in the operating instructions