Chicco ERGO GYM BABY TRAINER Manual page 11

20. Press both of the panel side joints at the same time, until the panel reaches position B, as shown in diagram I-2. A "click" will be heard when the joints are released,
indicating that they are fitted in the correct position.
21. Attach the swinging character, by inserting the fabric strap inside the hook (diag. L/L-1).
22. Fasten the fabric strap by inserting it into the buckle, as shown in diagram L-2; adjust the strap to the height that is most appropriate for your child.
23. Repeat the operation with the other swinging character. The frame will look as shown in diagram L-3.
24. To check whether the frame is in the correct position, ensure that the notches located on the joints are positioned on the 3/B combination.
Changing the Play Position from No. 1 to No. 2.
From 3-B to 2-C
1. Press both the backrest side joints at the same time, until the panel reaches position n. 1, as shown in diagram M. A "click" will be heard when the joints are
released, indicating that they are fitted in the correct position.
2. Press both the panel side joints at the same time, until the panel reaches position C, as shown in diagram M-1. A "click" will be heard when the joints are released,
indicating that they are fitted in the correct position.
3. Raise the backrest, until the notch located on the backrest joint reaches position n. 2, as shown in diagram M-2. A "click" will be heard when the joints are released,
indicating that they are fitted in the correct position.
4. Lower the backrest support, as shown in diagram M-3, and check that it is locked correctly into position.
5. If assembled correctly, the frame will look as shown in diagram H-4.
6. Raise the frame, as shown in diagram M-5.
7. Unfasten the Velcro strap that fixes the playmat to the backrest, as shown in diagram M-6.
8. Raise the playmat and pass the strap through the 3 holes (right, left and bottom), as shown in diagram M-7.
9. Place the child as shown in diagram M-8; then fasten the fabric straps into the buckle, as shown in diagram M-9.
10. When the Baby Trainer is in use, remember to always fasten the safety harness, inserting it through the crotch strap, and ensure that it is fastened correctly.
• Age for use in the baby seat position: from birth up to 9 Kg of weight (6 months approximately). Do not use the Baby Trainer in this position when the child is
able to sit on its own.
• Only place the Baby Trainer on flat, stable surfaces.
• Always use the safety harness and crotch strap when the child is sitting in the Baby Trainer in the baby seat position.
• WARNING: The Baby Trainer has not been specifically designed for a child to sleep in. If your child needs to rest, it is recommended to lay it in a crib or cot.
Changing the Play Position from No. 2 to No. 3.
From 2-C to 1-A
1. Remove the buckle from the playmat.
2. Unfasten the Velcro strap that fixes the playmat to the backrest, as shown in diagram N.
3. Pass the fabric straps under the playmat through the appropriate hole, as shown in diagram N-1; ensure that they do not prevent the baby from lying on its
tummy.
4. Fasten the 3 fabric straps with the Velcro straps, as shown in diagram N-2.
5. Press both the panel side joints at the same time, until the panel reaches position A, as shown in diagram N-3. A "click" will be heard when the joints are released,
indicating that they are fitted in the correct position.
6. Lift the frame from the floor, as shown in diagram N-4.
7. Raise the backrest support, as shown in diagram N-5, and replace it inside the backrest, as shown in diagram N-6.
8. Lower the backrest until the backrest reaches position n. 1.
9. The teething ring can be inserted in both sides, which have a slot where the triangular base of the teething ring can be inserted. See diagram N-7.
10. To check whether the frame is in the correct position, ensure that the notches located on the joints are positioned on the 1/A combination.
11. If assembled correctly, the frame will look as shown in diagram N-8.
The 2 swinging toys placed on the electronic panel can be removed at any time.
Changing the Play Position from No. 3 to No. 4
From 1-A to 1-C
1. Press both the panel joints at the same time, until the panel reaches position C, as shown in diagram O. A "click" will be heard when the joints are released,
indicating that they are fitted in the correct position.
2. To check whether the frame is in the correct position, ensure that the notches located on the joints are positioned on the 1/C combination.
3. If assembled correctly, the frame will look as shown in diagram O-1.
Warning: Always check that the 2 joints are locked into position (a click will be heard), before letting the child play with the toy.
HOW TO USE THE TOY IN PLAY MODE No. 1: GYM
In the gym play mode, the newborn baby lies in the horizontal position on the padded base and is free to move to optimise the development of its motor co-
ordination skills, by interacting with the hanging characters that activate music and light effects. The length of the hanging characters can be adjusted to select the
appropriate distance and ensure the correct movement of the baby.
To switch on the panel, simply move the switch, located on the left side of the panel, from the OFF to the 1 o 2 position, according to the desired play mode. A fun
light effect and a melody confirm that the toy is activated.
PLAY MODE 1
In this play mode, the child listens uninterrupted to the melodies for 3 minutes, without touching any of the gym activities. To re-activate the melodies after 3
minutes, touch the activities located on the panel or the 2 hanging characters. If the parent or child touches one of the 2 hanging characters when the melodies are
being played, some fun sound effects will be added.
PLAY MODE 2
In this play mode, the child must interact with the toy in order to listen to the melodies. The rabbit and tortoise invite the child to stretch its arms and touch the animal
characters to activate delightful melodies accompanied by fun light effects. This activity will help the child to develop its hand/eye co-ordination and stimulate its
listening and visual skills. If the child touches one of the hanging characters again when the melody is being played, some fun sound effects will be added.
HOW TO USE THE TOY IN PLAY MODE No. 2: BABY SEAT
In this position, the child sits on a comfortable support and is entertained by the light and music of the electronic panel.
In this position, the child can play:
• with the 2 hanging characters, as with the gym play mode, and can activate the music by touching the hanging characters with its feet. Positions 1 and 3 will
also be available, as with the gym play mode (see paragraph above).
11