Av tuner receiver / 5 and 7-channel power amplifier / dvd/sacd player / av surround sound receiver / dvd/cd players / dvd/cd/mp3 player / av surround sound receiver / stereo integrated amplifier / cd player (20 pages)
Page 2
IMPORTANT SAFETY INSTRUCTIONS Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
III. Additional Details on Configuring Your VISO System A. Important B. Selecting Speaker Wire C. Configurations D. Tighten Terminals E. NAD VISO DVD Receiver Setup F. Subwoofer Level G. Subwoofer LED Indicator H. AC Power Switch IV. Protecting Your Speakers V.
0° and volume switch to 0dB. Flip the Power Switch to the on position. E. Turn ON your NAD VISO DVD Receiver. If you're using an NAD VISO FIVE DVD Receiver, ensure that the settings for “Front”, “Centre” and “Surround”...
There can be sharp increases or decreases in the relative loudness of different frequency bands, greatly amplifying or almost nullifying whole ranges. Since VISO Speakers are small and easy to position, it's easy to experiment with small, incremental changes until you are satisfied.
horizontally and vertically. If you prefer the surround effect to be more diffused rather than pinpointed, aiming the speakers somewhat away from your ears probably will be more satisfying. You may want even to place them to reflect their sound off the sides or rear of you room rather than have them radiate toward you.
something with steady low frequencies (such as organ music) or continuous test tones, not movie material. Move around the room and note where the bass sounds best; if you place the subwoofer there and yourself in your chair, you should get the same bass performance. Bear in mind that the test only works if you have your ears as high off the floor as the subwoofer will be, so don’t be afraid to crawl around.
E. NAD VISO DVD Receiver Setup NAD VISO FIVE If you're using an NAD VISO FIVE DVD Receiver connected to an NAD VISO THIRTY and NAD VISO TWENTY, you must configure the Speaker Settings to calibrate the frequency response of the system. The following steps will guide you in configuring your NAD VISO FIVE with respect to NAD VISO THIRTY and NAD VISO TWENTY speakers.
Page 9
2. With “Audio Setup Menu” highlighted, press [ENTER] button to select “Audio Setup Menu” and correspondingly bring up the Audio Setup Menu OSD. Audio Setup Menu Listening Mode Input Settings Speakers Settings Speakers Distance Channel Levels Exit 3. Use the [ ] button to scroll down to “Speaker Settings”. Press [ENTER] to select “Speaker Settings”...
Page 10
A. With NAD VISO TWENTY speakers connected to the corresponding speaker terminals of your NAD VISO TWO, connect the supplied AC cord to NAD VISO TWO's AC Mains input and then plug into an AC outlet. B. The Standby LED indicator embedded around the bezel of the POWER button in the front panel will illuminate amber.
Page 11
the supplied HTR 6 remote control. Since the remote control will be the primary controller for most cases, the following procedures are all made with reference to the use of the appropriate HTR 6 button controls. Listening Mode 1. Using the HTR 6 remote control, press the [SETUP] button. The SETUP menu On-Screen-Display (OSD) will be shown in your connected TV/Monitor.
Page 12
4. While at the “Listening Mode” menu item, use the [ ] button to select “DVS Reference” – this is the calibrated listening mode setting when using the NAD VISO TWENTY speakers. Listening Mode Mode DVS Reference Do not Save & Exit Save &...
Channel Levels Exit 3. Press [ENTER]. While at the “Front” menu item, use the [ ] button to select the “Small” setting - this is the calibrated Speaker Setting when using the NAD VISO TWENTY speakers. Speaker Settings Front Small...
LED turns red. H. AC Power Switch The Power Switch turns the NAD VISO subwoofer on and off. As the subwoofer draws only an extremely small current when idle, this may be left normally on and turned off only when you do not expect to use the subwoofer for an extended period.
C. See your dealer if you require service. NAD dealers are equipped to handle almost all problems. If you have moved since your purchase, the nearest authorized NAD dealer should be able to help you.
Page 16
Thank you again for your purchase. We hope this owner's guide helps you enjoy the exceptional satisfaction that NAD VISO speaker systems have to offer. And we wish you many years of enjoyable listening!
Page 17
FIGURE 1 5.1 System with VISO FIVE VISO S10 120V Model Only VOLUME 0 db +10db 120V 60HZ 1.6A VISO S10 AC FUSE Powered Subwoofer T1.6AL 250V PHASE 0° 180° VISO C20 VISO LR5 VISO LR5 Centre Speaker Right Front Left Front Speaker Speaker...
Page 18
FIGURE 2 2.1 System with VISO TWO VISO S10 120V Model Only VOLUME 0 db +10db 120V 60HZ 1.6A VISO S10 AC FUSE Powered Subwoofer T1.6AL 250V PHASE 0° 180° VISO LR5 VISO LR5 Right Front Left Front Speaker Speaker...