Self-Diagnosis Code Table - Sony Handycam HDR-HC5 Service Manual

1-5-3. Self-diagnosis Code Table

Self-diagnosis Code
Block
Function
C 0 4
C 2 1
C 2 2
C 3 1
C 3 1
C 3 1
C 3 1
C 3 1
C 3 1
C 3 1
C 3 1
C 3 1
C 3 1
C 3 1
C 3 1
C 3 1
C 3 2
C 3 2
C 3 2
C 3 2
C 3 2
C 3 2
C 3 2
C 3 2
C 3 2
C 3 2
C 3 2
C 3 2
C 3 2
C 3 2
HDR-HC5/HC5E/HC7/HC7E_L2
Detailed Symptom/State
Code
0 0 Non-standard battery is used.
0 0 Condensation.
0 0 Video head is dirty.
LOAD direction. Loading does not
1 0
complete within specified time
UNLOAD direction. Loading does not
1 1
complete within specified time
2 0 T reel side tape slacking when unloading.
2 1 S reel side tape slacking when unloading.
2 2 T reel fault.
2 3 S reel fault.
3 0 FG fault when starting capstan.
3 1 FG fault during normal capstan operations.
4 0 FG fault when starting drum.
4 1 PG fault when starting drum.
4 2 FG fault during normal drum operations.
4 3 PG fault during normal drum operations.
4 4 Phase fault during normal drum operations.
LOAD direction loading motor time-
1 0
out.
UNLOAD direction loading motor
1 1
time-out.
T reel side tape slacking when
2 0
unloading.
S reel side tape slacking when
2 1
unloading.
2 2
T reel fault.
2 3
S reel fault.
3 0 FG fault when starting capstan.
FG fault during normal capstan
3 1
operations.
4 0 FG fault when starting drum.
4 1 PG fault when starting drum.
FG fault during normal drum
4 2
operations.
PG fault during normal drum
4 3
operations.
Phase fault during normal drum
4 4
operations.
Difficult to adjust focus.
6 0
(Cannot initialize focus. )
Use the InfoLITHIUM battery.
Remove the cassette, and insert it again after one hour.
Clean with the optional cleaning cassette.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
If it does not recover, inspect the focus MR sensor of lens block
(Pin ql, wa of CN5302 (HC5/HC5E) or Pin qh, qk of CN5301
(HC7/HC7E) on the LD-221 board).
If not faulty, inspect the focus motor drive circuit
(IC5404 on the LD-221 board).
1-3
ENGLISH JAPANESE
ENGLISH JAPANESE
Correction