Table of Contents
Advertisement
Using other functions
Using the sleep timer
The sleep timer switches the receiver into standby after a
specified amount of time so you can fall asleep without
worrying about the receiver being left on all night. Use
the remote control to set the sleep timer.
INPUT
SELECT
HDMI OUT
1
2
3
SIGNAL SEL
MCACC
SLEEP
4
5
6
SBch
A.ATT
DIMMER
7
8
9
D.ACCESS
CH LEVEL
CLASS
0
ENTER
•
Press
RECEIVER
, then press SLEEP repeatedly to set
the sleep time.
30 min
Off
• You can check the remaining sleep time at any time
by pressing SLEEP once. Pressing repeatedly will
cycle through the sleep options again.
Dimming the display
You can choose between four brightness levels for the
front panel display. Note that when selecting sources, the
display automatically brightens for a few seconds.
INPUT
SELECT
HDMI OUT
1
2
3
SIGNAL SEL
MCACC
SLEEP
4
5
6
SBch
A.ATT
DIMMER
7
8
9
D.ACCESS
CH LEVEL
CLASS
0
ENTER
•
Press
RECEIVER
, then press DIMMER repeatedly to
change the brightness of the front panel display.
Switching the HDMI output
(VSX-23TXH only)
Set which terminal to use when outputting video and
audio signals from the HDMI output terminals (HDMI
OUT ALL, HDMI OUT 1 or HDMI OUT 2).
The HDMI OUT1 terminal is compatible with the KURO
LINK function.
Note
1 • You can also switch off the sleep timer simply by switching off the receiver.
• The sleep timer is valid for all zones. If any zone is on, the sleep timer continues functioning.
2 • Synchronized amp mode on page 65 is canceled when the HDMI output is switched. If you wish to use the synchronized amp mode, switch
to HDMI OUT 1, then select the synchronized amp mode on the flat panel TV using the flat panel TV's remote control.
• When the power is turned off then back on after switching the HDMI output, the input is set to a setting between HDMI1 and HDMI3 (VSX-
21TXH)/4 (VSX-23TXH), or BD.
3 If the Pure Direct mode is switched on, some settings above will show OFF, even though they are on.
CH
AUDIO
INFO
DISP
RECEIVER
TV CTRL
REMOTE
SETUP
ZONE 2
ZONE 3
MAIN
60 min
90 min
1
AUDIO
INFO
CH
DISP
RECEIVER
TV CTRL
REMOTE
SETUP
ZONE 2
ZONE 3
MAIN
INPUT
SELECT
HDMI OUT
1
2
3
SIGNAL SEL
MCACC
SLEEP
4
5
6
SBch
A.ATT
DIMMER
7
8
9
D.ACCESS
CH LEVEL
CLASS
0
ENTER
•
Press
RECEIVER
, then press HDMI OUT.
Please wait a while when Please wait ... is displayed.
The output switches among HDMI OUT ALL, HDMI OUT 1
and HDMI OUT 2 each time the button is pressed.
Checking your system settings
Use the status display screen to check your current
settings for features such as surround back channel
processing and your current MCACC preset.
THX
PHASE CTRL
ANT
MPX
AUDIO
INFO
DISP
TV CTRL
REMOTE
SETUP
1
Press
RECEIVER
, then press STATUS to check the
system settings.
These appear on the front panel display.
The front panel display shows each of the following
settings for three seconds each:
Input Source
Sampling Frequency
Surround Back channel Processing
MCACC preset
ZONE 2 input
ZONE 3 input
(VSX-23TXH only)
KURO LINK
HDMI OUT
(VSX-23TXH only)
2
When you're finished, press STATUS again to
switch off the display.
CH
AUDIO
INFO
DISP
RECEIVER
TV CTRL
REMOTE
SETUP
ZONE 2
ZONE 3
MAIN
2
STATUS
PQLS
MEMORY
CH
RECEIVER
3
↓
↓
↓
↓
↓
↓
↓
08
71
En
Advertisement
Table of Contents
