Erasing One Of The Remote Control Button Settings; Resetting The Remote Control Presets - Pioneer Elite SC-09TX Operating Instructions Manual

Controlling the rest of your system
13
3 Press the input source button for the component
you want to control, then press ENTER.
PRES KEY shows in the LCD display.
4 Point the two remote controls towards each other,
then press the button that will be doing the learning on
this receiver's remote control.
PRES KEY starts flashing to indicate the remote is ready
to accept a signal.
• The remote controls should be 3 cm to 5 cm (1 to 2
inches) apart.
5 Press the corresponding button on the other
remote control that is sending (teaching) the signal to
this receiver's remote control.
For example, if you want to learn the playback control
signal, press and hold  briefly. The LCD display will
show OK if the operation has been learned.
If for some reasons the operation hasn't been learned the
LCD will display ERROR briefly, and then display PRES
KEY again. If this happens, keep pressing the (teaching)
button as you vary the distance between the two remotes,
until the LCD display shows OK.
Certain buttons represent operations that cannot be
learned from other remote controls. The buttons
available are shown below:
MAIN
RECEIVER
ZONE2
DVD BD
DVR1 DVR2
HOME MEDIA
GALLERY CD
TUNER PHONO
XM SIRIUS
TV
CH
TV CONTROL
INPUT
AUDIO
Note
1 • You can't assign the TUNER, iPod, HOME MEDIA GALLERY, XM or SIRIUS buttons.
• The TV CONTROL buttons (TV, TV VOL +/–, TV CH +/–, MUTE and INPUT) can only be learned after the operation selection switch is set to TV.
2 Note that interference from TVs or other devices will sometimes result in the remote control learning the wrong signal.
3 • Some commands from other remote controls cannot be learned, but in most cases the remotes just need to be moved closer together or farther apart.
• If the remote LCD shows FULL, it means the memory is full. See Erasing one of the remote control button settings below to erase a programmed button
you're not using to free up more memory (note that some signals may take more memory than others).
4 When Selecting preset codes directly on page 113 are set, all the signals learned in the input source buttons are cleared. This function is convenient when
you want to reset some but not all of input source buttons.
114
En
1
3 cm to 5 cm
(1 to 2 inches)
2
3
SOURCE
AUDIO VIDEO
PARAMETER PARAMETER
TUNE
3
MULTI
OPERATION
TOP MENU MENU
BAND T.EDIT
TV SAT
ST ST
ENTER
VIDEO1 VIDEO2
RETURN
SETUP
SACD CD-R
TUNE
CATEGORY
STATUS CH LEVEL
iPod HDMI
INPUT SELECT
THX MPX MEMORY
AUTO/ STEREO/
STANDARD ADV SURR
DIRECT F.S.SURR
SIGNAL SEL SLEEP DIMMER AUDIO
SOURCE
RCV
SR+ SBch PHASE iPod CTRL
DISP
VOL
A.ATT GENRE HDMI OUT
VOL
CH
D.ACCESS MCACC CLASS
ENTER
CLR
MUTE MUTE
VIDEO
6 To program additional signals for the current
component repeat steps 4 and 5.
To program signals for another component, exit and
repeat steps 1 through 5.
7 Press and hold the MULTI OPERATION button for a
couple of seconds to exit and store the operation(s).
Erasing one of the remote control
button settings
This erases one of the buttons you have programmed and
restores the button to the factory default.
1 While pressing the MULTI OPERATION button,
press SETUP.
The remote LCD display shows SETUP.
Use / to select ERASE, then press ENTER.
2
The LCD on the remote prompts you for the component
corresponding to the button setting to be erased.
3 Press the input source button corresponding to the
command to be erased, then press ENTER.
The LCD display flashes PRES KEY.
4 Press and hold the button to be erased for two
seconds.
The LCD display shows OK or NO CODE to confirm the
button has been erased.
5 Repeat step 4 to erase other buttons.
6 Press and hold the MULTI OPERATION button for a
couple of seconds when you're done.

Resetting the remote control presets

This will erase all preset remote control preset codes and
4
programmed buttons.
1 While pressing the MULTI OPERATION button,
press SETUP.
The remote LCD display shows SETUP.
Use / to select RESET, then press ENTER.
2
RESET flashes in the LCD display.
3 Press and hold ENTER for about two seconds.
The LCD shows OK to confirm the remote presets have
been erased.