Speaker Installation Option - Panasonic SC-PT170 Operating Instructions Manual

Speaker installation option

Attaching to a wall
You can attach all of the speakers (except subwoofer) to a wall.
≥ The wall or pillar on which the speakers are to be attached should be
capable of supporting 10 kg per screw. Consult a qualified building
contractor when attaching the speakers to a wall. Improper attachment
may result in damage to the wall and speakers.
1 Drive a screw (not included) into the wall.

4.0 mm
Wall or pillar
2 Fit the speaker securely onto the screw(s) with the hole(s).
Front speaker
[PT175]
Attach to a wall without the base and the stand.
116 mm
384 mm
Manufactured under license from Dolby Laboratories.
Dolby, Pro Logic, and the double-D symbol are trademarks of Dolby
Laboratories.
Manufactured under license under U.S. Patent #'s: 5,451,942;
5,956,674; 5,974,380; 5,978,762; 6,487,535 & other U.S. and
worldwide patents issued & pending. DTS and DTS Digital Surround
are registered trademarks and the DTS logos and Symbol are
trademarks of DTS, Inc. c 1996-2008 DTS, Inc. All Rights Reserved.
U.S. Patent Nos. 6,836,549; 6,381,747; 7,050,698; 6,516,132; and
5,583,936.
This product incorporates copyright protection technology that is
protected by U.S. patents and other intellectual property rights. Use of
this copyright protection technology must be authorized by
Macrovision, and is intended for home and other limited viewing uses
only unless otherwise authorized by Macrovision. Reverse
engineering or disassembly is prohibited.
HDMI, the HDMI logo and High-Definition Multimedia Interface are
trademarks or registered trademarks of HDMI Licensing LLC.
HDAVI Control TM is a trademark of Panasonic Corporation.
26
26
At least 30 mm
[PT170]

7.0 mm to 9.0 mm
[PT175]

7.0 mm to 9.4 mm
[PT170]
3 to 5 mm
[PT175]
4 to 6 mm
e.g.
In this position,
DO
the speaker will
likely fall if moved
NOT
to the left or right.
Move the speaker
so that the screw
DO
is in this position.
[PT170] Front speaker
Fitting speaker stands (not included)
[PT175]
Center and surround speakers only
Ensure the stands meet these conditions before purchasing them.
≥ The stands must be able to support over 10 kg.
≥ The stands must be stable even if the speakers are in a high position.
e.g. Surround speaker
Metal screw holes
For attaching to
speaker stands
Reattaching the speaker cable
[PT175]
Insert the cable from
the bottom.
Leave about
90 mm
Windows Media and the Windows logo are trademarks or registered
trademarks of Microsoft Corporation in the United States and/or other
countries.
This product is protected by certain intellectual property rights of
Microsoft Corporation and third parties. Use or distribution of such
technology outside of this product is prohibited without a license from
Microsoft or an authorized Microsoft subsidiary and third parties.
This product is licensed under the MPEG-4 Visual patent portfolio
license for the personal and non-commercial use of a consumer for (i)
encoding video in compliance with the MPEG-4 Visual Standard
("MPEG-4 Video") and/or (ii) decoding MPEG-4 Video that was
encoded by a consumer engaged in a personal and non-commercial
activity and/or was obtained from a video provider licensed by MPEG
LA to provide MPEG-4 Video. No license is granted or shall be implied
for any other use. Additional information including that relating to
promotional, internal and commercial uses and licensing may be
obtained from MPEG LA, LLC. See http://www.mpegla.com.
Plays DivX video
®
DivX ® is a registered trademark of DivX, Inc., and is used under license.
Plate thickness plus
7.0 mm to 10 mm
‰5.0 mm, pitch 0.8 mm
Speaker stand
(not included)
Pull out the cable
through the hole.