Panasonic SC-BTX70 Operating Instructions Manual page 45

Displays
The display is dim.
The elapsed time displayed is
actually less than the play time.
TV screen and video
The images from this unit do
not appear on the TV.
Picture is distorted.
Jittering occurs.
The screen changes
automatically.
Video is not output.
Video is not output in high
definition.
The Setup menu cannot be
accessed.
Status messages do not appear. ≥Select "Automatic" in "Status Messages" in the Setup menu.
The 4:3 aspect ratio picture
expands left and right.
Screen size is wrong.
When playing DVD-Video using
progressive output, one part of
the picture momentarily
appears to be doubled up.
There is no apparent change in
picture quality when adjusted
with the "Video" menu in the
on-screen menu.
The masked-off area is masked
in gray.
Still pictures (JPEG) do not
playback normally.
≥Change "FL Display" in the Setup menu.
≥The displayed play time is converted from the number of frames at 29.97 frames (equal to
0.999 seconds) to one second. There will be a slight difference between the time displayed
and the actual elapsed time (e.g., actual one-hour elapsed time may display as approximately
59 minutes 56 seconds).
≥Make sure that the TV is connected to the VIDEO OUT terminal or the HDMI AV OUT
terminal on this unit.
≥Make sure that the TV's input setting (e.g., VIDEO 1) is correct.
≥If "24p Output" is set to "On" when the unit is connected to a TV through any terminal other
than HDMI, images may not display properly. In this case, set "24p Output" to "Off".
≥When "24p Output" is set to "On", HDMI authentication takes place where 24p images switch
to other images, and a black screen is displayed.
≥When "24p Output" is set to "On", jittering may occur while playing DVD-Video. In this case,
turn "24p Output" to "Off".
≥An incorrect resolution is selected in "HDMI Resolution", when the TV is connected to HDMI
AV OUT terminals. While stopped, press and hold [1] and [∫] on the main unit at the same
time for more than 5 seconds to cancel this setting. Set the item again. However, Dolby
Digital Plus, Dolby TrueHD, and DTS-HD audio are not output in bitstream. To output the
bitstream, select "Restore Default Settings" to restore the factory presets and make proper
settings.
≥Picture may not be seen when more than 2 devices are connected with HDMI cables.
Reduce the number of connected devices.
≥Mobile telephone chargers can cause some disturbance.
≥If you are using an indoor TV antenna, change to an outdoor antenna.
≥The TV antenna wire is too close to the unit. Move it away from the unit.
≥When the "Screen Saver Function" in the Setup menu is set to "On", the display may return to
the screen saver mode automatically if there is no operation for 5 minutes or more.
≥An image is not output from the VIDEO OUT terminal when the "High Clarity Sound" is
enabled. Set the "High Clarity Sound" in the on-screen menu to "Off" to use the VIDEO OUT
terminal.
≥High definition video cannot be output through the VIDEO OUT terminal.
≥Confirm that the "HDMI Resolution", in the Setup menu is set properly.
≥Select "BD/DVD" or "SD" as the source.
≥Use the TV to change the aspect. Refer to your TV's operating instructions.
≥When using an HDMI cable, set "TV Aspect" to "16:9".
≥Connect this unit to the TV with any cable except the HDMI cable.
≥The effect is less perceivable with some types of video.
≥If the "Screen Saver Function" in the Setup menu is set to "Off", the masked-off area is
displayed in black.
≥The images that were edited on the PC, such as Progressive JPEG, etc., may not playback.
Page
35
—
9
—
36
36
36
36
—
—
—
—
35
33
—
36
14
35
—
36
9
—
35
41
RQT9479
45