NEC NP-P350W User Manual
  1. Manuals
  2. Brands
  3. NEC Manuals
  4. Projector
  5. NP-P350W
  6. User manual

NEC NP-P350W User Manual

Nec np-p350w: user guide
Hide thumbs Also See for NP-P350W:
Table of Contents

Advertisement

Quick Links

See also: Installation Manual
Portable Projector
P420X/P350X/P350W
User's Manual
Model No.
NP-P420X, NP-P350X, NP-P350W

Advertisement

Table of Contents
loading

Related Manuals for NEC NP-P350W

Summary of Contents for NEC NP-P350W

  • Page 1 Portable Projector P420X/P350X/P350W User’s Manual Model No. NP-P420X, NP-P350X, NP-P350W...
  • Page 2 (3) Great care has been taken in the preparation of this user’s manual; however, should you notice any questionable points, errors or omissions, please contact us. (4) Notwithstanding article (3), NEC will not be responsible for any claims on loss of profit or other matters deemed to result from using the Projector.

  • Page 3: Important Information

    Important Information Safety Cautions Precautions Please read this manual carefully before using your NEC projector and keep the manual handy for future reference. CAUTION To turn off main power, be sure to remove the plug from power outlet. The power outlet socket should be installed as near to the equipment as possible, and should be easily accessible.

  • Page 4: Important Safeguards

    The Federal Communications Commission does not allow any modifications or changes to the unit EXCEPT those specified by NEC Display Solutions of America, Inc. in this manual. Failure to comply with this government regu- lation could void your right to operate this equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
  • Page 5 Important Information WARNING • Do not use any other object than the projector’s sliding lens cover to cover the lens while the projector is on. Doing so can cause the object to get extremely hot, and possibly resulting in a fire or damage due to the heat emitted from the light output.
  • Page 6 Important Information • Do not place any objects, which are easily affected by heat, in front of a projector exhaust vent. Doing so could lead to the object melting or getting your hands burned from the heat that is emitted from the ex- haust.

  • Page 7: Lamp Replacement

    Important Information Note for US Residents The lamp in this product contains mercury. Please dispose according to Local, State or Federal Laws. Lamp Replacement • Use the specified lamp for safety and performance. • To replace the lamp, follow all instructions provided on page 147. •...
  • Page 8 Important Information Information on Wireless LAN: In some areas and countries, the P420X, P350X, and P350W series projectors come standard with the USB Wireless LAN Unit. If you purchase the projector model without the Wireless LAN Unit, the optional Wireless LAN Unit must be installed to use the projector via a wireless connection.
  • Page 9 NP02LM) è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Spanish Por medio de la presente NEC Display Solutions, Ltd. declara que el Wireless LAN Unit (Model: NP02LM) cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
  • Page 10 Important Information Table of Supported Areas and Countries Note that use with other than the combinations of the product names and supported countries and areas listed below may violate radio wave laws of the country where the device is used. Product Name Supported countries and areas NP02LM1...
  • Page 11 Important Information • FCC Compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.
  • Page 12 Important Information Regulatory Statement: Operation of this device is subjected to the following National regulations and may be prohibited to use if certain restriction should be applied. France: Outdoor use limited to 10mW e.i.r.p. within the band 2454 – 2483.5 MHz. Derogation in French overseas departments of Guyane and La Reunion: outdoor use not allowed in band 2400 - 2420 MHz.

  • Page 13: Specifications

    Important Information Specifications (1) Specifications common to the NP02LM series Operating Voltage 5V (power supplied from the projector) MAX Amps 460 mA Wireless Standard IEEE802.11b / IEEE802.11g / IEEE802.11n Modulation Method CCK / DQPSK / DBPSK / OFDM / DS-SS LED Display During communication: blinking (Green)
  • Page 14 Important Information NP02LM2 IEEE802.11b Center Frequency Range/ 2412 to 2472 MHz Operating channels 1 to 13 channels Transmission method DS-SS method (direct dispersion spectrum dispersion method) Data Rates 11/5.5/2/1 Mbps IEEE802.11g Center Frequency Range/ 2412 to 2472 MHz Operating channels 1 to 13 channels Transmission method OFDM method (Orthogonal Frequency Division Multiplex-...

  • Page 15: Table Of Contents

    Table of Contents Important Information ....................i 1. Introduction ......................1 1 What’s in the Box? ......................1  Introduction to the Projector ..................2 Congratulations on Your Purchase of the Projector ..........2 Features you’ll enjoy: ....................2 About this user’s manual ..................3 ...
  • Page 16 Table of Contents Checking Energy-Saving Effect [CARBON METER] ..........29  Preventing the Unauthorized Use of the Projector [SECURITY] ......... 30  Operating Your Computer’s Mouse Functions from the Projector’s Remote Control via the USB Cable (Remote Mouse Function) ............33 ...
  • Page 17 Table of Contents  Menu Descriptions & Functions [SETUP] ..............91 [GENERAL] ......................91 [MENU] ........................93 [INSTALLATION] ....................95 [OPTIONS(1)] ......................97 [OPTIONS(2)] ......................99  Menu Descriptions & Functions [INFO.] ..............101 [USAGE TIME] ..................... 101 [SOURCE]......................102 [WIRED LAN] .......................
  • Page 18 Table of Contents  Projecting Your Computer’s Screen Image from the Projector over a LAN (Image Express Utility Lite) ....................160  Projecting an Image from an Angle (Geometric Correction Tool in Image Express Utility Lite) ......................163 What you can do with GCT .................. 163 Projecting an Image from an Angle (GCT) ............

  • Page 19: Introduction

    (7N520073) (EU: 7N080022) For North America only Registration card Limited warranty For customers in Europe: NEC Projector CD-ROM You will find our current valid Guar- User’s manual (PDF) and the utility antee Policy on our Web Site: www.nec-display-solutions.com software • Important Infomation (For North America:...

  • Page 20: Introduction To The Projector

    1. Introduction  Introduction to the Projector This section introduces you to your new projector and describes the features and controls. Congratulations on Your Purchase of the Projector This projector is one of the very best projectors available today. The projector enables you to project precise images up to 300 inches across (measured diagonally) from your PC or Macintosh computer (desktop or notebook), VCR, DVD player, or document camera.

  • Page 21: About This User's Manual

    Software programs (User Supportware) contained in the supplied CD-ROM The supplied NEC Projector includes seven programs: Virtual Remote Tool, Image Express Utility Lite, Image Express Utility 2.0, Desktop Control Utility 1.0, PC Control Utility Pro 4, Viewer PPT Converter 3.0, and Image Express Utility 2 for Mac.

  • Page 22: Part Names Of The Projector

    1. Introduction  Part Names of the Projector Front/Top Controls Zoom Lever (→ page 20) (→ page 6) Focus Lever Lens Shift Dial (Vertical) (→ page 19) (→ page 18) Ventilation (outlet) Ventilation (inlet) / Filter Cover Heated air is exhausted from here. (→...

  • Page 23: Rear

    1. Introduction Rear Port Cover for Remote Sensor USB Wireless LAN Unit (→ page 9) When using the USB Wireless LAN Unit, first remove the cover. (→ Lamp Cover (→ page 148) page 141) Built-in Security Slot ( Monaural Speaker (10 W) Terminal Panel (→...

  • Page 24: Top Features

    1. Introduction Top Features (POWER) Button (→ page 14, 25) 2. POWER Indicator (→ page 13, 14, 25, 192) 3. STATUS Indicator (→ page 192) 4. LAMP Indicator (→ page 147, 192) 5. ECO Button (→ page 28) 6. SOURCE Button (→ page 16) 7.

  • Page 25: Terminal Panel Features

    1. Introduction Terminal Panel Features 13 12 1. COMPUTER 1 IN/ Component Input Connector (Mini D-Sub 15 Pin) (→ page 132, 136, 157) 2. COMPUTER 1 AUDIO IN Mini Jack (Stereo Mini) (→ page 132, 134, 136) 3. COMPUTER 2 IN / Component Input Connector (Mini D-Sub 15 Pin) (→...

  • Page 26: Part Names Of The Remote Control

    1. Introduction  Part Names of the Remote Control 11. VIEWER Button (→ page 16, 56) 12. NETWORK Button (→ page 16) 13. USB DISPLAY Button (→ page 16) 14. ID SET Button (→ page 96) 15. Numeric Keypad Button/CLEAR Button (→...

  • Page 27: Battery Installation

    1. Introduction Battery Installation Press firmly and slide the battery Install new batteries (AAA). Ensure Slip the cover back over the bat- cover off. that you have the batteries’ polarity teries until it snaps into place. Do (+/−) aligned correctly. not mix different types of batteries or new and old batteries.

  • Page 28: Operating Environment For Software Included On Cd-Rom

    • Image Express Utility Lite does not support “Meeting Mode” in Image Express Utility 2.0 and Image Express Utility 2 for Mac included with our other models. Download service For the update information about these software programs, visit our website: URL: http://www.nec-display.com/dl/en/index.html...

  • Page 29: Operating Environment

    1. Introduction Operating Environment The following is the operating environment for Image Express Utility Lite. For the operating environment of other soft- ware program, refer to the help function of each software program. Supported OS Windows 7 Home Basic Windows 7 Home Premium Windows 7 Professional Windows 7 Ultimate Windows 7 Enterprise...

  • Page 30: Projecting An Image (Basic Operation)

    2. Projecting an Image (Basic Operation) This section describes how to turn on the projector and to project a picture onto the screen. 1 Flow of Projecting an Image Step 1 • Connecting your computer / Connecting the power cord (→ page 13) Step 2 •...

  • Page 31: Connecting Your Computer/Connecting The Power Cord

    2. Projecting an Image (Basic Operation)  Connecting Your Computer/Connecting the Power Cord 1. Connect your computer to the projector. This section will show you a basic connection to a computer. For information about other connections, see “6. Installation and Connections” on page 132. Connect the computer cable (VGA) between the projector’s COMPUTER 1 IN connector and the computer’s port (mini D-Sub 15 Pin).

  • Page 32: Turning On The Projector

    2. Projecting an Image (Basic Operation)  Turning on the Projector 1. Slide the lens cover to the left to uncover the lens. 2. Press the (POWER) button on the projector cabinet or the POWER ON button on the remote control. The POWER indicator will turn to blue and the projector will become ready to use.

  • Page 33: Note On Startup Screen (Menu Language Select Screen)

    2. Projecting an Image (Basic Operation) Note on Startup screen (Menu Language Select screen) When you first turn on the projector, you will get the Startup menu. This menu gives you the opportunity to select one of the 27 menu languages. To select a menu language, follow these steps: 1.

  • Page 34: Selecting A Source

    2. Projecting an Image (Basic Operation)  Selecting a Source Selecting the computer or video source NOTE: Turn on the computer or video source equipment connected to the projector. Detecting the Signal Automatically Press the SOURCE button once.The projector will search for the available input source and display it.

  • Page 35: Adjusting The Picture Size And Position

    2. Projecting an Image (Basic Operation)  Adjusting the Picture Size and Position Use the lens shift dial, the adjustable tilt foot lever, the zoom lever and the focus lever to adjust the picture size and position. In this chapter drawings and cables are omitted for clarity. Adjusting the vertical position of a projected image Adjusting the focus [Lens shift]...

  • Page 36: Adjusting The Vertical Position Of A Projected Image (Lens Shift)

    2. Projecting an Image (Basic Operation) Adjusting the vertical position of a projected image (Lens shift) Rotate the lens shift dial. In this user’s manual, the upward maximum shift is referred to as “normal position”. Downward Upward Lens shift dial NOTE: The lens shift dial cannot be rotated beyond the maximum upward or downward shift.

  • Page 37: Focus

    2. Projecting an Image (Basic Operation) Ceiling front projection [P420X/P350X] Vertical shift range (0 to 0.5V) Height of projected image [P350W] Vertical shift range (0 to 0.6V) Height of projected image Focus Use the FOCUS lever to obtain the best focus. Focus Lever...

  • Page 38: Zoom

    2. Projecting an Image (Basic Operation) Zoom Use the ZOOM lever to adjust the image size on the screen. Zoom Lever...

  • Page 39: Adjust The Tilt Foot

    2. Projecting an Image (Basic Operation) Adjust the Tilt Foot 1. Lift the front edge of the projector. CAUTION: Do not try to touch the ventilation outlet during Tilt Foot adjustment as it can become heated while the projector is turned on and after it is turned off.

  • Page 40: Correcting Keystone Distortion Manually

    2. Projecting an Image (Basic Operation)  Correcting Keystone Distortion Manually If the screen is tilted vertically, keystone distortion becomes large. To correct keystone distortion manually, proceed with the following steps to correct keystone distortion. NOTE: • The maximum range of vertical keystone correction is +/−30 degrees. •...

  • Page 41: Adjusting With The Remote Control

    2. Projecting an Image (Basic Operation) Adjusting with the remote control 1. Press the KEYSTONE button. The Keystone bar will be displayed. 2. Use the  or  button to correct the keystone distortion. Adjust so that the right and left sides are parallel. 3.

  • Page 42: Optimizing Computer Signal Automatically

    2. Projecting an Image (Basic Operation)  Optimizing Computer Signal Automatically Adjusting the Image Using Auto Adjust Optimizing a computer image automatically. (COMPUTER1/COMPUTER2) Press the AUTO ADJ. button to optimize a computer image automatically. This adjustment may be necessary when you connect your computer for the first time. [Poor picture] [Normal picture] NOTE:...

  • Page 43: Turning Off The Projector

    2. Projecting an Image (Basic Operation)  Turning off the Projector To turn off the projector: 1. First, press the (POWER) button on the projector cabinet or the POWER OFF button on the remote con- trol. The [POWER OFF / ARE YOU SURE ? / CARBON SAV- INGS- SESSION 0.000[g-CO2]] message will appear.

  • Page 44: After Use

    2. Projecting an Image (Basic Operation)  After Use Preparation: Make sure that the projector is turned off. 1. Unplug the power cord. 2. Disconnect any other cables. • Remove the USB memory if it is inserted into the projector. 3.

  • Page 45: Convenient Features

    3. Convenient Features 1 Turning off the Image and Sound Press the AV-MUTE button to turn off the image and sound for a short period of time. Press again to restore the image and sound. The projector’s power-saving function will work 10 seconds after the image is turned off.

  • Page 46: Changing Eco Mode/Checking Energy-Saving Effect Using Eco Mode [Eco Mode]

    3. Convenient Features 2. Press the  button. The area of the magnified image will be moved 3. Press the D-ZOOM (−) button. Each time the D-ZOOM (−) button is pressed, the image is reduced. NOTE: • The image will be enlarged or reduced at the center of the screen. •...

  • Page 47: Checking Energy-Saving Effect [Carbon Meter]

    3. Convenient Features NOTE: • The [ECO MODE] can be changed by using the menu. Select [SETUP] → [GENERAL] → [ECO MODE]. • The lamp life remaining and lamp hours used can be checked in [USAGE TIME]. Select [INFO.] → [USAGE TIME]. •...

  • Page 48: Preventing The Unauthorized Use Of The Projector [Security]

    3. Convenient Features  Preventing the Unauthorized Use of the Projector [SECURITY] A keyword can be set for your projector using the Menu to avoid operation by an unauthorized user. When a keyword is set, turning on the projector will display the Keyword input screen. Unless the correct keyword is entered, the pro- jector cannot project an image.
  • Page 49 3. Convenient Features 7. Type in the same combination of  buttons and press the ENTER button. The confirmation screen will be displayed. 8. Select [YES] and press the ENTER button. The SECURITY function has been enabled. To turn on the projector when [SECURITY] is enabled: 1.
  • Page 50 3. Convenient Features To disable the SECURITY function: 1. Press the MENU button. The menu will be displayed. 2. Select [SETUP] → [INSTALLATION] → [SECURITY] and press the ENTER button. The OFF/ON menu will be displayed. 3. Select [OFF] and press the ENTER button. The SECURITY KEYWORD screen will be displayed.

  • Page 51: Operating Your Computer's Mouse Functions From The Projector's Remote Control

    3. Convenient Features  Operating Your Computer’s Mouse Functions from the Projector’s Remote Control via the USB Cable (Remote Mouse Function) The built-in remote mouse function enables you to operate your computer’s mouse functions from the supplied remote control when the projector is connected to a computer via a commercially available USB cable (compatible with USB 2.0 specifications).

  • Page 52: (Usb Display)

    • To make USB DISPLAY available on Windows XP, the Windows user account must have “Administrator” privilege. • USB Display uses functions of Image Express Utility Lite contained on NEC Projector CD-ROM (→ page 160). Starting USB Display, however, will not install Image Express Utility Lite on your computer. This is because USB Display executes the projector’s program only.
  • Page 53 3. Convenient Features 5. Operate the control window. (Source) ����� Selects an input source of the projector� (Picture) ���� Turns on or off the AV-MUTE (Picture mute), FREEZE (Freeze a picture), and Geometric Correction Tool (GCT) functions� (Sound) ����� Turns on or off AV-MUTE (Sound mute), play the sound and turns up or down the volume� (Etc) �����������...

  • Page 54: Controlling The Projector By Using An Http Browser

    • Start the Web browser on the computer via the network connected to the projector and enter the following URL : http://<the projector’s IP address> /index.html • Use Image Express Utility Lite contained on the supplied NEC Projector CD-ROM. TIP: The factory setting IP address is [DHCP ON]. NOTE: •...

  • Page 55: Handling Of The Address For Operation Via A Browser

    IP address of the projector has been set in the “HOSTS” file of the computer being used. Example 1: When the host name of the projector has been set to “pj.nec.co.jp”, access is gained to the network setting by specifying http://pj.nec.co.jp/index.html...
  • Page 56 3. Convenient Features PICTURE: Controls the video adjustment of the projector. BRIGHTNESS  ���� Increases the brightness adjustment value� BRIGHTNESS  ���� Decreases the brightness adjustment value� CONTRAST  �������� Increases the contrast adjustment value� CONTRAST  �������� Decreases the contrast adjustment value� COLOR ...
  • Page 57 3. Convenient Features NETWORK SETTINGS • SETTINGS WIRED or WIRELESS SETTING Set for wired LAN or for wireless LAN. APPLY Apply your settings to wired LAN or wireless LAN. DHCP ON Automatically assign IP address, subnet mask, and gateway to the projector from your DHCP server.
  • Page 58 3. Convenient Features SSID Enter an identifier (SSID) for wireless LAN. Communication can be done only with equipment whose SSID matches SSID for your wireless LAN. SITE SURVEY Displays a list of available SSIDs for wireless LAN on site. Select an SSID which you can access.
  • Page 59 Sample of a message to be sent from the projector: The lamp and filters are at the end of its usable life. Please replace the lamp and filters. Projector Name: NEC Projector Lamp Hours Used: 100 [H] SENDER’S ADDRESS Enter sender’s address.
  • Page 60 3. Convenient Features • NETWORK SERVICE PJLink PASSWORD Set a password for PJLink*. A password must be 32 characters or less. Do not forget your password. However, if you forget your password, consult with your dealer. HTTP PASSWORD Set a password for HTTP server. A password must be 10 characters or less. AMX BEACON Turn on or off for detection from AMX Device Discovery when connecting to the network supported by AMX’s NetLinx control system.

  • Page 61: Projecting Your Computer's Screen Image From The Projector Via A Network [Network Projector]

    3. Convenient Features  Projecting Your Computer’s Screen Image from the Projector via a Network [NETWORK PROJECTOR] By selecting the projector connected to the same network as that of your PC, the PC screen image can be projected to the screen via network. There is no need of connection using the computer cable (VGA). Operation Environment Applicable OS Windows 7 Professional...
  • Page 62 3. Convenient Features 2. Press the SELECT  or  button to select [NETWORK] and press the ENTER button. In the screen, the [APPLICATION MENU] menu is displayed. 3. From the [APPLICATION MENU] menu, select [NETWORK PROJECTOR]. The [PROJECTOR NAME/DISPLAY RESOLUTION/PASSWORD/URL] will be displayed.
  • Page 63 3. Convenient Features Projecting the Image with Network Projector 1. Click [Start] from the desktop of Windows 7. 2. Click [All Programs]. 3. Click [Accessories]. 4. Click [Connect to a Network Projector]. When the [Permission Connect to a Network Projector] window appears,click [Yes.]. The “Connect to a Network Projector”...
  • Page 64 3. Convenient Features 7. Input the password to the password input box displayed by the operation at step 3 on page 44. 8. Click [Connect]. The network projector function works and the screen of Windows 7 is projected from the projector. •...

  • Page 65: Using The Projector To Operate Your Computer Via A Network

    3. Convenient Features  Using the Projector to Operate Your Computer via a Network [REMOTE DESKTOP] • By selecting the PC connected to the same network as that of the projector, the PC screen image can be projected to the screen via network. Then, by operating the keyboard, you can operate Windows 7, Windows Vista or Windows XP on the PC connected with the network.
  • Page 66 3. Convenient Features Setting the password to the user account of Windows 7 TIP: If a password has been set for an account, the steps 1 to 9 can be skipped. 1. Click [Start] from the desktop of Windows 7. 2.
  • Page 67 3. Convenient Features 4. Click [View status] displayed in blue on the right of [Local Area Connection] in the window. The [Local Area Connection Status] window appears. 5. Click [Details...]. Write down the value for “IPv4 IP Address” (xxx.xxx.xxx.xxx) displayed. 6.
  • Page 68 3. Convenient Features 2. Press the SELECT  or  button to select [NETWORK] and press the ENTER button. The [NETWORK] menu will be displayed. 3. From the [NETWORK] menu, use the wireless keyboard to select [REMOTE DESKTOP CONNECTION]. The [REMOTE DESKTOP CONNECTION] window appears. 4.
  • Page 69 3. Convenient Features Exiting the Remote Desktop 1. Operate the wireless keyboard to click [Start] from the desktop screen projected by the projector. 2. Click [X] on the right of the start menu. The remote desktop function is stopped. 3. Press the SOURCE button of the projector to select an input terminal other than [NETWORK]. When using the remote control, press a button other than the NETWORK button.

  • Page 70: Using The Viewer

    4. Using the Viewer ❶ What you can do with the Viewer The Viewer feature allows you to view slides or movie files stored on a USB memory on the projector, or a shared folder in a computer connected to the network. The Viewer has the following features.

  • Page 71: Supported Usb Memory Devices

    4. Using the Viewer NOTE: • Movie files converted by using the video/audio format which is not supported by this projector cannot be played back. In this case, there will be no icon to show that playback is not possible. •...
  • Page 72 4. Using the Viewer Notices on shared folder and media server • Files from a shared folder or media server may not be projected if security or antivirus software is installed on your computer. • Open the following firewall ports: - Media server Port number Protocol...

  • Page 73: ❷ Preparing Presentation Materials

    4. Using the Viewer ❷ Preparing presentation materials 1. Create your presentation materials and save them in a supported file format to your computer. • See page for supported file formats. • Make sure that PowerPoint file is displayed on the Viewer before giving your real presentation. With Viewer PPT Converter 3.0 contained the supplied CD-ROM, you can convert your PowerPoint files to index files that can be displayed on the Viewer.

  • Page 74: ❸ Projecting Images Stored In A Usb Memory Device

    4. Using the Viewer ❸ Projecting images stored in a USB memory device This section explains the basic operation of the Viewer. The explanation provides the operational procedure when the Viewer toolbar is set to the factory default. Preparation: Before starting the Viewer, store images to the USB memory using your computer. Starting the Viewer 1.
  • Page 75 4. Using the Viewer 4. Press the ▶ button to select “USB1” and press the ENTER button. The “USB1” thumbnail screen will be displayed. TIP: • For more information about thumbnail screen, see page 62. 5. Use the ▲▼◀ or ▶ button to select an icon. •...
  • Page 76 4. Using the Viewer • Movie file The movie file will start playing. After finishing the playback, the screen will turn to black. Press the EXIT button to return to the thumbnail screen. • Pressing the ENTER button will display the movie’s control bar with which you can pause or fastforward and some other operations.

  • Page 77: Exiting The Viewer

    4. Using the Viewer • Index file (extension:.idx) • Index files, which is converted by using Viewer PPT Converter 3.0, will appear in the Thumbnail screen. Only folders and JPEG files converted by using Viewer PPT Converter 3.0 will appear in the Thumbnail screen.

  • Page 78: Names And Functions Of Viewer Screen

    4. Using the Viewer Names and functions of Viewer screen The Viewer has three screens: Drive list screen, Thumbnail screen, and Slide screen. Cursor (yellow) Cursor (yellow) Scroll bar Menu Menu Folder icon [Drive list screen] [Thumbnail screen] Path information Drive information/File information Operation button guide Menu guide...
  • Page 79 4. Using the Viewer Functions Name Description REFRESH Displays additional media servers in the drive list screen. OPTIONS Opens the OPTIONS menu. SLIDE SETTING Sets up slides. (→ page 65) MOVIE SETTING Sets up movie files. (→ page 66) AUTO PLAY SETTING Sets up auto play. (→ page 66) SHAREED FOLDER Sets up a shared folder.
  • Page 80 4. Using the Viewer • Thumbnail screen Displays a list of folders, thumbnails, and icons in the drive selected on the drive list screen. Menu operation • Use the ▼ or ▲ button to move the cursor up or down. Select the menu item and press the ENTER button to display the menu or setting screen.
  • Page 81 4. Using the Viewer • Slide screen (still image/movie) Plays a file selected from a list of thumbnails or icons. • For operating a Microsoft PowerPoint file and Adobe PDF file, see page 58. Control bar operation • The control bar will be displayed only when a still image (or index file) and a movie file is selected. •...
  • Page 82 4. Using the Viewer Functions of movie control bar Name Description PREV Goes back to the beginning of a movie file. • Goes back to the beginning of the previous movie file if executed immediately after being started playing. Fast-rewinds a movie file for about 7 seconds. PLAY/PAUSE PLAY Plays a movie file.

  • Page 83: Viewer Option Settings

    4. Using the Viewer Viewer option settings • SLIDE SETTING Sets still images or slides. Name Options Description SCREEN SIZE BEST FIT Displays the image with its aspect ratio in the projector’s display- able maximum resolution. ACTUAL SIZE Displays the image in its actual size. PLAY MODE MANUAL Selects manual play.
  • Page 84 4. Using the Viewer • MOVIE SETTING Sets the functions for a movie file. Name Options Description SCREEN SIZE BEST FIT Displays the image with its aspect ratio in the projector’s display- able maximum resolution. ACTUAL SIZE Displays the image in its actual size. REPEAT Turns on or off the repeat function.
  • Page 85 4. Using the Viewer • SORT SETTING Sets the order of displaying thumbnails or slides. Name Options Description SORT NAME (ABC..) Displays the files alphabetically by name in ascending order. NAME (ZYX..) Displays the files alphabetically by name in descending order. EXT.

  • Page 86: ❹ Projecting Data From Shared Folder

    4. Using the Viewer ❹ Projecting data from shared folder Shared folder Wireless LAN Projector Shared folder Preparation For projector: Connect the projector to the network. For computer: Place files to be projected in a shared folder and note the folder’s path. Memorize or write down the path for later use.
  • Page 87 4. Using the Viewer 2. Displays the [OPTIONS] menu. Press the ▼ button to select the (OPTIONS) icon and press the ENTER button. • When the OPTIONS menu is displayed, the drive list will not be displayed. 3. Display the [SHARED FOLDER SETTING] screen. Press the ▼...
  • Page 88 4. Using the Viewer 6. Exit the setting. Press the ▼ button to select [OK] and press the ENTER button. This will close the [SHARED FOLDER] screen. • If an error message appear, your settings are not correct. Try again.

  • Page 89: Disconnecting The Shared Folder From The Projector

    4. Using the Viewer Disconnecting the shared folder from the projector • Disable the number of a shared folder you wish to disconnect Press the ▼ button to select [ENABLE] and press the ENTER button to clear it. NOTE: • When a PowerPoint file or PDF file is displayed, do not disconnect your LAN cable. If doing so, the Viewer will not work. TIP: •...

  • Page 90: ❺ Projecting Data From Media Server

    4. Using the Viewer ❺ Projecting data from media server Media server Wireless LAN Media server Projector Media server Preparation For projector: Connect the projector to the network. For computer: Prepare image files or movie files to be projected, and set up “Media Sharing” in Windows Media Player 11 or Windows Media Player 12.
  • Page 91 4. Using the Viewer 3. Select “Share my media” check box, and then select OK. A list of accessible devices will be displayed. 4. Select “P420 Series” and then “Allow”. A check mark will be added to the “P420 Series” icon. •...

  • Page 92: Setting Up "Media Sharing" In Windows Media Player 12

    4. Using the Viewer Setting up “Media Sharing” in Windows Media Player 12 1. Start Windows Media Player 12. 2. Select “Stream”, and then select “Automatically allow devices to play my media”. The “Allow All Media Devices” windows will be displayed. 3.

  • Page 93: Connecting The Projector To The Media Server

    4. Using the Viewer Connecting the projector to the media server Press the VIEWER button on the remote control. The VIEWER will start. • Another way to start the VIEWER is to press the SOURCE button a few times on the projector cabinet. (→ page •...

  • Page 94: Disconnecting The Projector From The Media Server

    4. Using the Viewer Disconnecting the projector from the media server 1. Display the OPTIONS menu. Press the ▼ button to select the [OPTIONS] icon and select the ENTER button. 2. Display the MEDIA SERVER setting screen. Press the ▼ button to select the MEDIA SERVER icon and press the ENTER button. 3.

  • Page 95: ❻ Restrictions On Displaying Files

    4. Using the Viewer ❻ Restrictions on displaying files The Viewer allows you to give a simplified display of a PowerPoint file or PDF file. Due to simplified display, however, actual display may be different from the one on your computer application pro- gram.

  • Page 96: Using On-Screen Menu

    5. Using On-Screen Menu 1 Using the Menus NOTE: The on-screen menu may not be displayed correctly while interlaced motion video image is projected. 1. Press the MENU button on the remote control or the projector cabinet to display the menu. NOTE: The commands such as ENTER, EXIT, , ...

  • Page 97: Menu Elements

    5. Using On-Screen Menu  Menu Elements Slide bar Solid triangle Available buttons Source Highlight Radio button Wireless symbol ECO mode symbol Off Timer remaining High Altitude symbol time Thermometer symbol Key Lock symbol Menu windows or dialog boxes typically have the following elements: Highlight �����������������������������Indicates the selected menu or item�...

  • Page 98: List Of Menu Items

    5. Using On-Screen Menu  List of Menu Items • Basic menu items are indicated by shaded area. Some menu items are not available depending on the input source. Menu Item Default Options COMPUTER1 COMPUTER2 HDMI VIDEO SOURCE S-VIDEO VIEWER NETWORK USB DISPLAY PRESET...
  • Page 99 5. Using On-Screen Menu DESKTOP DESKTOP FRONT, CEILING REAR, DESKTOP REAR, ORIENTATION FRONT CEILING FRONT CONTROL PANEL LOCK OFF, ON SECURITY OFF, ON COMMUNICATION SPEED 38400bps 4800bps, 9600bps, 19200bps, 38400bps REMOTE SENSOR FRONT/BACK FRONT/BACK, FRONT, BACK INSTALLATION CONTROL ID 1–254 CONTROL ID NUMBER CONTROL ID...

  • Page 100: Menu Descriptions & Functions [Source]

    5. Using On-Screen Menu  Menu Descriptions & Functions [SOURCE] COMPUTER 1 and 2 Selects the computer connected to your COMPUTER 1 or COMPUTER 2 input connector signal. NOTE: When the component input signal is connected to the COMPUTER 1 IN or COMPUTER 2 IN connector, select [COMPUTER1] or [COMPUTER2] respectively.

  • Page 101: Menu Descriptions & Functions [Adjust]

    5. Using On-Screen Menu  Menu Descriptions & Functions [ADJUST] [PICTURE] [PRESET] This function allows you to select optimized settings for your projected image. You can adjust neutral tint for yellow, cyan or magenta. There are seven factory presets optimized for various types of images. You can also use [DETAIL SETTINGS] to set user adjustable settings to customize each gamma or color.
  • Page 102 5. Using On-Screen Menu [GENERAL] Storing Your Customized Settings [REFERENCE] This function allows you to store your customized settings in [PRESET 1] to [PRESET 7]. First, select a base preset mode from [REFERENCE], then set [GAMMA CORRECTION] and [COLOR TEMPERA- TURE].
  • Page 103 5. Using On-Screen Menu [CONTRAST] Adjusts the intensity of the image according to the incoming signal. [BRIGHTNESS] Adjusts the brightness level or the back raster intensity. [SHARPNESS] Controls the detail of the image. [COLOR] Increases or decreases the color saturation level. [HUE] Varies the color level from +/−...

  • Page 104: [Image Options]

    5. Using On-Screen Menu [IMAGE OPTIONS] Adjusting Clock and Phase [CLOCK/PHASE] This allows you to manually adjust CLOCK and PHASE. CLOCK ������������������� Use this item to fine tune the computer image or to remove any vertical banding that might appear� This function adjusts the clock frequencies that eliminate the horizontal banding in the image�...
  • Page 105 5. Using On-Screen Menu Adjusting Horizontal/Vertical Position [HORIZONTAL/VERTICAL] Adjusts the image location horizontally and vertically. NOTE: The [HORIZONTAL] and [VERTICAL] items are not available for VIDEO, S-VIDEO, HDMI, VIEWER, NETWORK, and USB DISPLAY. - An image can be distorted during the adjustment of [CLOCK] and [PHASE]. This is not malfunction. - The adjustments for [CLOCK], [PHASE], [HORIZONTAL], and [VERTICAL] will be stored in memory for the current signal.
  • Page 106 5. Using On-Screen Menu Selecting Aspect Ratio [ASPECT RATIO] The term “aspect ratio” refers to the ratio of width to height of a projected image. The projector automatically determines the incoming signal and displays it in its appropriate aspect ratio. •...
  • Page 107 5. Using On-Screen Menu Sample image when the appropriate aspect ratio is automatically determined P420X/P350X [Computer signal] Aspect ratio of incoming signal 16:9 15:9 16:10 Sample image when the appro- priate aspect ratio is automati- cally determined [Video signal] Aspect ratio of incoming signal Letterbox Squeeze Sample image when the as-...

  • Page 108: [Audio]

    5. Using On-Screen Menu [AUDIO] Turning Up or Down Sound Adjusts the volume of the projector speaker and AUDIO OUT (Stereo Mini Jack). TIP: • When no menus appear, the ◀ and ▶ buttons on the projector cabinet and the VOL. +/− buttons on the remote control work as a volume control.

  • Page 109: Menu Descriptions & Functions [Setup]

    5. Using On-Screen Menu  Menu Descriptions & Functions [SETUP] [GENERAL] Correcting Vertical Keystone Distortion Manually [KEYSTONE] You can correct vertical distortion manually. (→ page 22) TIP: When this option is highlighted, pressing the ENTER button will display its slide bar for adjustment. Saving Vertical Keystone Correction [KEYSTONE SAVE] This option enables you to save your current keystone settings.
  • Page 110 5. Using On-Screen Menu Using the Wall Color Correction [WALL COLOR] This function allows for quick adaptive color correction in applications where the screen material is not white. NOTE: Selecting [WHITEBOARD] reduces lamp brightness. Setting Eco Mode [ECO MODE] The ECO MODE increases lamp life, while lowering power consumption and cutting down on CO emissions.

  • Page 111: [Menu]

    5. Using On-Screen Menu Setting Closed Caption [CLOSED CAPTION] This option sets several closed caption modes that allow text to be superimposed on the projected image of Video or S-Video. OFF ������������������������ This exits the closed caption mode� CAPTION 1-4 ��������� Text is superimposed� TEXT 1-4 ����������������...
  • Page 112 5. Using On-Screen Menu Turning ON/OFF Control ID [ID DISPLAY] ID DISPLAY ����������� This option turns on or off the ID number which is displayed when the ID SET button on the remote control is pressed� Turning On / Off Eco Message [ECO MESSAGE] This option turns on or off the following messages when the projector is turned on.

  • Page 113: [Installation]

    5. Using On-Screen Menu [INSTALLATION] Selecting Projector Orientation [ORIENTATION] This reorients your image for your type of projection. The options are: desktop front projection, ceiling rear projection, desktop rear projection, and ceiling front projection. DESKTOP FRONT CEILING REAR DESKTOP REAR CEILING FRONT Disabling the Cabinet Buttons [CONTROL PANEL LOCK] This option turns on or off the CONTROL PANEL LOCK function.
  • Page 114 5. Using On-Screen Menu Selecting Communication Speed [COMMUNICATION SPEED] This feature sets the baud rate of the PC Control port (D-Sub 9P). It supports data rates from 4800 to 38400 bps. The default is 38400 bps. Select the appropriate baud rate for your equipment to be connected (depending on the equip- ment, a lower baud rate may be recommended for long cable runs).

  • Page 115: [Options(1)]

    5. Using On-Screen Menu Using Test Pattern [TEST PATTERN] Displays the test pattern to check for image distortion at the time of the projector setup. Press the ENTER button to display the test pattern; press the EXIT button to close the test pattern and return to the menu. Menu operation and keystone correction are not possible when the test pattern is displayed.
  • Page 116 5. Using On-Screen Menu Selecting Signal Format [SIGNAL SELECT] [COMPUTER1], [COMPUTER2] Allows you to choose [COMPUTER1], or [COMPUTER2] for an RGB source such as a computer, or [COMPONENT] for a component video source such as a DVD player. Normally select [RGB/COMPONENT] and the projector auto- matically detects a component signal.

  • Page 117: [Options(2)]

    5. Using On-Screen Menu [OPTIONS(2)] Selecting Power-saving in [STANDBY MODE] The projector has two standby modes: [NORMAL] and [POWER-SAVING]. The POWER-SAVING mode is the mode that allows you to put the projector in the power-saving condition which consumes less power than the NORMAL mode. The projector is preset for NORMAL mode at the factory. NORMAL ����������������...
  • Page 118 5. Using On-Screen Menu Turning On the Projector By Applying Computer Signal [AUTO POWER ON(COMP1)] When the projector is in Standby mode, applying a computer signal from a computer connected to the COMPUTER1 IN input will power on the projector and simultaneously project the computer’s image. This functionality eliminates the need to always use the POWER button on the remote control or the projector cabinet to power on the projector.

  • Page 119: Menu Descriptions & Functions [Info.]

    5. Using On-Screen Menu  Menu Descriptions & Functions [INFO.] Displays the status of the current signal and lamp usage. This item has six pages. The information included is as follows: TIP: Pressing the HELP button on the remote control will show the [INFO.] menu items. [USAGE TIME] [LAMP LIFE REMAINING] (%)* [LAMP HOURS USED] (H)

  • Page 120: [Source]

    5. Using On-Screen Menu [SOURCE] [SOURCE NAME] [SOURCE INDEX] [HORIZONTAL FREQUENCY] [VERTICAL FREQUENCY] [SIGNAL TYPE] [VIDEO TYPE] [SYNC TYPE] [SYNC POLARITY] [SCAN TYPE] [WIRED LAN] [IP ADDRESS] [SUBNET MASK] [GATEWAY] [MAC ADDRESS] [WIRELESS LAN] [IP ADDRESS] [SUBNET MASK] [GATEWAY] [MAC ADDRESS] [SSID] [NETWORK TYPE] [WEP/WPA]...

  • Page 121: [Version(1)]

    5. Using On-Screen Menu [VERSION(1)] [FIRMWARE] Version [DATA] Version [VERSION(2)] [FIRMWARE2] Version [OTHERS] [PROJECTOR NAME] [MODEL NO.] [SERIAL NUMBER] [LAN UNIT TYPE] [CONTROL ID] (when [CONTROL ID] is set)

  • Page 122: Menu Descriptions & Functions [Reset]

    5. Using On-Screen Menu  Menu Descriptions & Functions [RESET] Returning to Factory Default [RESET] The RESET feature allows you to change adjustments and settings to the factory preset for a (all) source (s) except the following: [CURRENT SIGNAL] Resets the adjustments for the current signal to the factory preset levels. The items that can be reset are: [PRESET], [CONTRAST], [BRIGHTNESS], [COLOR], [HUE], [SHARPNESS], [ASPECT RATIO], [HORIZONTAL], [VERTICAL], [CLOCK], [PHASE], and [OVERSCAN].

  • Page 123: ❾ Application Menu

    The application menu allows you to set up the User Supportware, Network Settings (NETWORK SETTINGS) and Tools (TOOLS). The User Supportware is contained on the supplied NEC Projector CD-ROM. In [ADMINISTRATOR MODE], either [ADVANCED] menu or [BASIC] menu can be selected. (→ page 123) The [BASIC] menu contains minimum essentials of menus and commands.

  • Page 124: Network Projector

    5. Using On-Screen Menu NETWORK PROJECTOR This shows information for projector name, resolution, and network (wired/wireless) which are required to use Network Projector. Use this information to set up for your computer. REMOTE DESKTOP CONNECTION This allows you to set up for computer name entry and effects for Remote Desktop. NOTE: •...

  • Page 125: Network Settings

    Express Utility and connecting the PC and projector via a wireless LAN. The Image Express Utility Lite, Image Express Utility 2.0, and Image Express Utility 2 for Mac are contained on the supplied NEC Projector CD-ROM. To use [EASY CONNECTION], select [WIRELESS LAN] → [PROFILES] → [EASY CONNECTION].
  • Page 126 5. Using On-Screen Menu WIRED LAN or WIRELESS LAN (ADVANCED menu only) PROFILES • Up to two settings for the LAN port or USB wireless LAN unit — can be stored in memory of the projector. Total of four settings can be stored.
  • Page 127 5. Using On-Screen Menu • When selecting [WPS], the network will be connected by using settings stored automatically with the WPS function. Selecting [WPS] will allow the projector to access the network by using the settings the WPS function automatically stored. DHCP Place a check mark to automatically assign an IP address to the —...
  • Page 128 5. Using On-Screen Menu SITE SURVEY Displays a list of available SSIDs for wireless LAN on site. Select — an SSID which you can access. To select an SSID, highlight [SSID] and use the SELECT → to select [OK] and press the ENTER button. �����������������������...
  • Page 129 5. Using On-Screen Menu When [WEP(64bit)] or [WEP(128bit)] is selected for [SECURITY TYPE] KEY SELECT Selects one WEP key from the four keys below. KEY1, KEY2, KEY3, Enter a WEP key. KEY4 • Maximum number of characters Option Alphanumeric (ASCII) Hexadecimal (HEX) WEP 64bit WEP 128bit...
  • Page 130 5. Using On-Screen Menu [AUTHENTICATION] (required for wireless only) Setting is required for using WPA-EAP or WPA2-EAP. Preparation before setting Select a wireless LAN compliant WPA-EAP or WPA2-EAP authentication and install a digital certificate on the projec- tor. 1. Set [DATE AND TIME] on the projector. (→ page 127) 2.
  • Page 131 5. Using On-Screen Menu 4. Select [SITE SURVEY] and press the ENTER button. The “SSID” list will be displayed. 5. Select a connecting SSID, and then select [OK]. Finally press the ENTER button. • Select the SSID for which WPA-PSK or WPA2-PSK is set. •...
  • Page 132 5. Using On-Screen Menu 11.Select the [AUTHENTICATION] tab. The [AUTHENTICATION] page will be displayed. Select either [EAP-TLS] or [PEAP-MSCHAPv2] for [EAP TYPE]. The setting items vary depending on the EAP type. See the table below. EAP Type Setting Item Note EAP-TLS User Name 1 character or more and 32 characters or...
  • Page 133 5. Using On-Screen Menu 13.Select [CLIENT CERTIFICATE] and press the ENTER button. A list of files (thumbnail screen) will be displayed. • For operating the thumbnail screen, see “4. Using the Viewer” in the “User’s Manual” (PDF). • To return to the [AUTHENTICATION] page, press the EXIT button. NOTE: Installing a digital certificate You can install each digital certificate (client certificate and CA certificate) for [PROFILE 1 (or 2)] on a file-by-file basis.
  • Page 134 5. Using On-Screen Menu 17.On the thumbnail screen, select a digital certificate (DER format file) saved in your USB memory device and press the ENTER button. • Select your root CA certificate here. The selected digital certificate will be installed on the projector. 18.After completing required settings, select [OK] and press the ENTER button.
  • Page 135 5. Using On-Screen Menu 15.After completing setting a user name, select the [PASSWORD] field and press the ENTER button. The character entry screen (software keyboard) will be displayed. Set a password. • A password must be 32 characters or less. 16.After completing setting the password, select [CA CERTIFICATE] field and press the ENTER button.
  • Page 136 5. Using On-Screen Menu 18.After completing required settings, select [OK] and press the ENTER button. The [WIRELESS] page will be returned. 19.Select [RECONNECT] and press the ENTER button. 20.Select [OK] and press the ENTER button. This will complete setting [PEAP-MSCHAPv2] for [EAP TYPE] in [WPA-EAP] or [WPA2-EAP]. TIP: Clearing the digital certificate that is installed on the projector To clear the digital certificate installed on the projector, follow the steps below.
  • Page 137 5. Using On-Screen Menu When the wireless LAN access point connected to the projector supports WPS (Wi-Fi Protected Setup TM), you can use PIN method or push button method to set up the wireless LAN for the projector. PIN TYPE Set a 4-digit or 8 digit-PIN code of WPS for your access point to complete setting for the SSID security.
  • Page 138 5. Using On-Screen Menu PROJECTOR NAME (ADVANCED menu only) PROJECTOR NAME Set a unique projector name. Up to 16 alphanu- meric characters and symbols DOMAIN (ADVANCED menu only) Set a host name and domain name of the projector. HOST NAME Set a host name of the projector.
  • Page 139 Sample of a message to be sent from the projector: The lamp and filters are at the end of its usable life. Please replace the lamp and filters. Projector Name: NEC Projector Lamp Hours Used: 100 [H] HOST NAME Type in a host name.
  • Page 140 5. Using On-Screen Menu NETWORK SERVICE (ADVANCED menu only) HTTP SERVER Set a password for your HTTP server. Up to 10 alphanumeric characters PJLink This option allows you to set a password when you use the Up to 32 alphanumeric PJLink feature.

  • Page 141: Tools

    5. Using On-Screen Menu TOOLS ADMINISTRATOR MODE This allows you to select MENU MODE, save settings, and set a password for the administrator mode. MENU MODE Select either [BASIC] or [ADVANCED] menu. — (→ page 80) Placing a check mark will not save your projector settings� NOT SAVE SETTING —...
  • Page 142 5. Using On-Screen Menu PROGRAM TIMER This option turns on/off the projector and changes video signals, and selects ECO mode automatically at a specified time. NOTE: • Before using [PROGRAM TIMER], make sure that the [DATE AND TIME] feature is set. (→ page 127) •...
  • Page 143 5. Using On-Screen Menu TIME ���������������������� Set the time to execute the program� Enter time in 24-hour format� FUNCTION ������������� Select a function to be executed� Selecting [POWER] will allow you to turn on or off the projector by setting [ADVANCED SETTINGS]� Selecting [SOURCE] will allow you to select a video source by setting [ADVANCED SETTINGS]�...
  • Page 144 5. Using On-Screen Menu Activating the program timer 1. Select [ENABLE] on the [PROGRAM TIMER] screen and press the ENTER button. The [ENABLE] will be activated. 2. Select [OK] and press the ENTER button. The [PROGRAM TIMER] screen will be changed to the [TOOL] screen. NOTE: •...
  • Page 145 5. Using On-Screen Menu DATE ANDTIME You can set the current time, month, date, and year. NOTE: The projector has a built-in clock. The clock will keep working for about 2 weeks after the main power is turned off. If the main power is off for 2 weeks or more, the built-in clock will cease.

  • Page 146: Installation And Connections

    6. Installation and Connections This section describes how to set up your projector and how to connect video and audio sources. Your projector is simple to set up and use. But before you get started, you must first: z Set up a screen and the projector. x Connect your computer or video equipment to the projector.
  • Page 147 6. Installation and Connections [P350W] The further your projector is from the screen or wall, the larger the image. The minimum size the image can be is approximately 25" (0.64 m) measured diagonally when the projector is roughly 37 inches (0.9 m) from the wall or screen.

  • Page 148: Throw Distance And Screen Size

    6. Installation and Connections Throw Distance and Screen Size The following shows the proper relative positions of the projector and screen. Refer to the table to determine the position of installation. Distance Chart B = Vertical distance between lens center and screen center C = Throw distance D = Vertical distance between lens center and...
  • Page 149 Contact your NEC dealer if you need a mirror * Do not attempt to install the projector yourself. system. If you’re using a mirror system and your image is inverted, use the MENU and ...

  • Page 150: Making Connections

    Usually, the combination of the “Fn” key along with one of the 12 function keys gets the external display to come on or off. For example, NEC laptops use Fn + F3, while Dell laptops use Fn + F8 key combinations to toggle through external display selections.
  • Page 151 USB DISPLAY (USB DISPLAY) NOTE: The projector is not compatible with video decoded outputs of the NEC ISS-6020 switcher. NOTE: An image may not be displayed correctly when a Video or S-Video source is played back via a commercially available scan converter.

  • Page 152: Connecting An External Monitor

    6. Installation and Connections Connecting an External Monitor AUDIO OUT MONITOR OUT (COMP. 1) Stereo mini-plug audio cable Computer cable (VGA) (not supplied) (not supplied) Com- puter cable (VGA) (supplied) AUDIO PHONE You can connect a separate, external monitor to your projector to simultaneously view on a monitor the computer analog image you’re projecting.

  • Page 153: Connecting Your Dvd Player Or Other Av Equipment

    6. Installation and Connections Connecting Your DVD Player or Other AV Equipment Connecting Video/S-Video Input VIDEO IN S-VIDEO IN AUDIO IN S-Video cable (not supplied) Video cable (not supplied) Audio cable (not supplied) Audio equipment S-VIDEO VIDEO AUDIO IN VIDEO OUT AUDIO OUT Audio cable (not supplied) •...

  • Page 154: Connecting Component Input

    6. Installation and Connections Connecting Component Input COMPUTER 1 IN AUDIO IN 15-pin - to - RCA (fe- Stereo mini plug - to - RCA audio male) × 3 cable adapter cable (not supplied) (ADP-CV1E) Audio Equipment Component video RCA × 3 AUDIO IN cable (not supplied) DVD player...

  • Page 155: Connecting Hdmi Input

    6. Installation and Connections Connecting HDMI Input You can connect the HDMI output of your DVD player, hard disk player, Blu-ray player, or notebook type PC to the HDMI IN connector of your projector. NOTE: The HDMI IN connector supports Plug & Play (DDC2B). HDMI IN HDMI HDMI cable (not supplied)

  • Page 156: Connecting To A Wired Lan

    6. Installation and Connections Connecting to a Wired LAN The projector comes standard with a LAN port (RJ-45) which provides a LAN connection using a LAN cable. To use a LAN connection, you are required to set the LAN on the projector menu. Select [APPLICATION MENU] → [NETWORK SETTINGS] →...

  • Page 157: Connecting To A Wireless Lan (Np02Lm Series)

    6. Installation and Connections Connecting to a Wireless LAN (NP02LM series) The USB Wireless LAN Unit also provides a wireless LAN connection. To use a wireless LAN connection, you are required to assign an IP address to the projector. NOTE: A wireless LAN unit is equipped with the projector for models distributed in North America models.
  • Page 158 6. Installation and Connections Example of wireless LAN connection (Network Type → Infrastructure) PC with wireless PC with built-in wireless LAN card inserted LAN function USB Wireless LAN Unit Wireless access point Wired LAN Use the HTTP server function to make the settings. (→ page 36) Example of wireless LAN connection (Network Type →...

  • Page 159: Removing And Attaching The Usb Wireless Lan Unit

    6. Installation and Connections Removing and attaching the USB Wireless LAN Unit NOTE: • The USB Wireless LAN Unit must be inserted into the USB Wireless LAN Unit port in the correct direction. It cannot be inserted in the reverse direction. If the USB Wireless LAN Unit is inserted in the reverse direction with excessive force applied, the USB port may break.

  • Page 160: Attaching The Optional Cable Cover (Np01Cv)

    6. Installation and Connections Attaching the Optional Cable Cover (NP01CV) An optional cable cover (NP01CV) is available for hiding cables. The NP01CV cable cover is designed for use with the P420X, P350X, and P350W. CAUTION: • Be sure to tighten the screws after attaching the cable cover. Failure to do so may cause the cable cover to come off and fall, resulting in injury or damage to the cable cover.

  • Page 161: Maintenance

    7. Maintenance This section describes the simple maintenance procedures you should follow to clean the filters, the lens, the cabinet, and to replace the lamp and the filters. 1 Cleaning the Filters The air-filter sponge keeps dust and dirt from getting inside the projector and should be frequently cleaned. If the filter is dirty or clogged, your projector may overheat.
  • Page 162 7. Maintenance (2) Push the left end of each filter and remove the hard two honeycomb filters (large and small). • The large filter cannot be removed by pushing on its right end. 4. Use a vacuum cleaner to vacuum all the dust inside. Get rid of dust in the accordion filter NOTE: •...
  • Page 163 7. Maintenance 7. Put the filter unit back to the projector cabinet. Make sure that the filter unit is placed in the correct orienta- tion. 8. Put the filter cover back to the projector cabinet. Insert two catches of the top side of the filter cover into the groove of the cabinet, and push the buttons on the left and right to close the filter cover.

  • Page 164: Cleaning The Lens

    7. Maintenance  Cleaning the Lens • Turn off the projector before cleaning. • The projector has a plastic lens. Use a commercially available plastic lens cleaner. • Do not scratch or mar the lens surface as a plastic lens is easily scratched. •...

  • Page 165: Replacing The Lamp And The Filters

    Do not touch them as the pieces of glass may cause injury. If this happens, contact your NEC dealer for lamp replacement.
  • Page 166 7. Maintenance To replace the lamp: 1. Remove the lamp cover. (1)Loosen the lamp cover screw • The lamp cover screw is not removable. (2)Push and slide the lamp cover off. 2. Remove the lamp housing. (1)Loosen the two screws securing the lamp housing until the phillips screwdriver goes into a freewheeling condi- tion.
  • Page 167 7. Maintenance 3. Install a new lamp housing. (1)Insert a new lamp housing until the lamp housing is plugged into the socket. (2)Push the top center of the lamp housing to secure it. (3)Secure it in place with the two screws. •...
  • Page 168 7. Maintenance To replace the filters: Four filters are packaged with the replacement lamp. Honeycomb filter (coarse mesh): Large and small sizes (attached to the outside of the filter unit) Accordion filter (fine mesh): Large and small sizes (attached to the inside of the filter unit) NOTE: •...
  • Page 169 7. Maintenance (2) Push the left end of each filter and remove the hard two honeycomb filters (large and small). • The large filter cannot be removed by pushing on its right end. 4. Remove dust from the filter unit and the filter cover. Clean both outside and inside.

  • Page 170: User Supportware

    If the message “There is not enough free space on destination” is displayed, free up enough space (about 100 MB) to install the program. 1 Insert the accompanying NEC Projector CD-ROM into your CD-ROM drive. The menu window will be displayed.
  • Page 171 8. User Supportware 2 Click a software program you wish to install on the menu window. The installation will start. • Follow the instructions on the installer screens to complete the installation. TIP: Uninstalling a Software Program Preparation: Exit the software program before uninstalling. To uninstall the software program, the Windows user account must have “Administrator”...

  • Page 172: Installation For Macintosh Software

    8. User Supportware Installation for Macintosh software Image Express Utility 2 for Mac supports Mac OS X. 1 Insert the accompanying NEC Projector CD-ROM into your CD-ROM drive. The menu window will be displayed. 2 Double-click the CD-ROM icon. 3 Double-click the “Mac OS X” folder.

  • Page 173: Using The Computer Cable (Vga) To Operate The Projector (Virtual Remote Tool)

    • Virtual Remote Tool can be used with a LAN and a serial connection. • For update information on Virtual Remote Tool, visit our website: http://www.nec-display.com/dl/en/index.html NOTE: • When [COMPUTER 1] is selected from your source selection, the Virtual Remote screen or the toolbar will be displayed as well as your computer screen.
  • Page 174 • Exit all running programs before installing Virtual Remote Tool. If another program is running, the installation may not be com- pleted. 1 Insert the accompanying NEC Projector CD-ROM into your CD-ROM drive. The menu window will be displayed. TIP: If the menu window will not be displayed, try the following procedure.
  • Page 175 8. User Supportware TIP: Uninstalling Software Program Preparation: Exit the software program before uninstalling. To uninstall the software program, the Windows user account must have “Administrator” privilege (Windows 7 and Windows Vista) or “Computer Administrator” privilege (Windows XP). • For Windows 7/Windows Vista 1 Click “Start”...
  • Page 176 Windows Desktop. Start from the Start menu • Click [Start] → [All Programs] or [Programs] → [NEC Projector User Supportware] → [Virtual Remote Tool] → [Virtual Remote Tool]. When Virtual Remote Tool starts for the first time, “Easy Setup” window will be displayed.
  • Page 177 The Help screen will be displayed. • Displaying the help file using the Start Menu. 1. Click “Start”.“All programs” or “Programs”.“NEC Projector User Supportware”.“Virtual Remote Tool”. and then “Virtual Remote Tool Help” in this order. The Help screen will be displayed.

  • Page 178: Projecting Your Computer's Screen Image From The Projector Over A Lan

    If the message “There is not enough free space on destination” is displayed, free up enough space (about 100 MB) to install the program. 1. Insert the accompanying NEC Projector CD-ROM into your CD-ROM drive. The menu window will be displayed.

  • Page 179: Connect The Projector To A Lan

    Wireless LAN (standards for North America, optional: NP02LM series)” (→ page 139) and “9 Application Menus” (→ page 105) Start Image Express Utility Lite. 1. On Windows, click “Start” → “All programs” → “NEC Projector UserSupportware” → “Image Express Utility Lite” → “Image Express Utility Lite”. Image Express Utility Lite will start.
  • Page 180 The Help screen will be displayed. • Displaying the help file using the Start Menu. Click “Start” → “All programs” or “Programs” → “NEC Projector User Supportware” → “Image Express Utility Lite” → “Image Express Utility Lite Help”. The Help screen will be displayed.

  • Page 181: Projecting An Image From An Angle

    8. User Supportware  Projecting an Image from an Angle (Geometric Correction Tool in Image Express Utility Lite) The Geometric Correction Tool (GCT) function allows you to correct distortion of images projected even from an angle. What you can do with GCT •...
  • Page 182 8. User Supportware 3. Use the mouse to click the [ • ] mark of which corner you wish to move. The currently selected [ • ] mark will turn red. (In the above example, Windows screens are omitted for clarification.) 4.

  • Page 183: Projecting Images Or Videos From The Projector Over A Lan (Image Express Utility 2.0)

    When “Meeting Mode” is used, projected images can be sent and received between two or more computers. • High-speed, high-quality image transmissions based on NEC’s original compression algorithm NEC’s original compression algorithm allows high-quality images to be sent over the network at high speed, from your computer to the projector. •...

  • Page 184: Connecting The Projector To A Lan

    8. User Supportware • Projected images can be transferred and saved to computers. When “Meeting Mode” is used, projected images can be sent to the computers of all the participants (attendants) of a “Meeting”. The received images can be saved to your computer with a memo (text data) attached. Attendant Attendant Presenter...

  • Page 185: Basic Operation Of Image Express Utility 2.0

    1 Turn on the power to the projector for which LAN has been set. 2 Click Windows [Start] → [All Programs] → [NEC Projector User Supportware] → [Image Express Utility 2.0] → [Image Express Utility 2.0 ], in that order.
  • Page 186 8. User Supportware 4 Check( ) the projector to connect and click [Connect]. If the name of the projector to connect is not on the list or if it is hidden, click [Update]. Click Click The screen of your computer will be projected from the projector. At this time, the input signal of the projector will automatically change to “NETWORK”.
  • Page 187 8. User Supportware • Stopping or resuming the transmission of images The transmission of the screen of the computer to the projector can be temporarily stopped and then resumed. 1 Click the projector icon ( ) on the Windows taskbar. A pop-up menu will be displayed.

  • Page 188: Holding Conferences

    8. User Supportware Holding Conferences • Holding conferences 1 Follow steps 1 through 4 in “Connecting projector” of “Sending Images to Projector” (→ page 167). The screen of your computer will be projected from the projector. • Disclose a file to the participants of the conference. NOTE: To disclose a file to the participants, selection can be made only in folder units.

  • Page 189: Participating In Conference

    Participating in Conference • Participating in conferences 1 Click Windows [Start] → [All Programs] → [NEC Projector User Supportware] → [Image Express Utility 2.0] → [Image Express Utility 2.0 ], in that order. The “Selection Of Network Connections” window will be displayed.
  • Page 190 8. User Supportware 3 Click the Meeting Name to participate, and click [Connect]. Click The computer will be connected to the selected conference and the attendant window will be displayed. If the presenter selects “Send to PC And Projector”, the image projected from the projector is displayed in the at- tendant window.
  • Page 191 8. User Supportware • Saving received images 1 Click [Memo] in the attendant window. A memo pane will be displayed. Click Memo pane Click 2 Click [Save Image] in the attendant window. The image displayed in the attendant window will be saved. •...
  • Page 192 8. User Supportware • Downloading disclosed file 1 Click [File Transfer] in the attendant window. The “File Transfer” window will be opened. Click 2 Select a file to download, and click [Download]. Downloading will begin. The progress of the downloading is displayed at the lower left of the window. 3 When downloading is complete, click [File] in the “File Transfer”...
  • Page 193 8. User Supportware • Changing presenter Three types of settings may be made to change the presenter: “Not Approved”, “Approved”, and “Changing Prohibited” (these can be selected only by the presenter). In the following example, “Not Approved” is selected. • Click [Become A Presenter] in the attendant window. You will change from a participant to a presenter.

  • Page 194: Using The Projector To Operate Your Computer Over A Lan (Desktop Control Utility 1.0)

    Therefore, care must be exercised to prevent any third party from viewing the screen of your computer (important documents), copying files, or turning off the power. NEC assumes no liability for any loss or damages arising from information leak or system failure while you are using Desktop Control Utility 1.0.

  • Page 195: Using The Projector To Operate Your Computer's Desktop Screen

    8. User Supportware Using the projector to operate your computer’s desktop screen IMPORTANT: • In case of Windows 7/Windows Vista, disable the user account control before using Desktop Control Utility 1.0. Windows Vista has “User Account Control” function to protect the computer. The user account confirmation window may be displayed.
  • Page 196 8. User Supportware • Operation on computer 1 Click Windows [Start] → [All Programs] → [NEC Projector User Supportware] → [Desktop Control Utility 1.0] → [Desktop Control], in that order. The “Selection Of Network Connections” window is displayed. This displays a list of the network devices connected to the computer you are using.
  • Page 197 8. User Supportware 3 Input the starting password of Desktop Control Utility 1.0, and click [OK]. The “Current password” window will be displayed. NOTE: The character string displayed in the password field varies each time Desktop Control Utility 1.0 is started. 4 Write down the character string displayed in the password field.
  • Page 198 8. User Supportware • Operating the projector (connecting computer) 1 Connect a USB mouse that is commercially available to the projector. 2 Turn on the power to the projector. Set the LAN setting of the projector in advance. 3 Press the SOURCE button on the projector unit. The Source list will be displayed.
  • Page 199 8. User Supportware 5 Click [DESKTOP CONTROL UTILITY]. The “DESKTOP CONTROL UTILITY menu” screen will be displayed. 6 Click “ENTRY”. A password input screen will be displayed. 7 Input the password you have written down in step 4 of “Operation on computer”. •...
  • Page 200 8. User Supportware 10 Click the computer at the connection destination and then [OK]. The desktop screen of the computer at the connection destination will be displayed. • Operating the projector (manipulating desktop screen) The displayed desktop screen can be manipulated by using the USB mouse connected to the projector. If the EXIT button of the projector or remote control is pressed while the desktop screen is displayed, an auxiliary operation bar is displayed at the lower left of the screen.
  • Page 201 8. User Supportware <1> <2> <3> <4> <1> (cut-off icon) �������Disconnects communication with the computer� <2> (Shift icon) ����������When the highlight is moved to this icon and the ENTER button is pressed, shift lock status is set� The shift lock is canceled if the highlight is moved to this icon and the ENTER button is pressed again�...
  • Page 202 8. User Supportware • Operating the projector (exiting Desktop Control Utility 1.0) 1 Click the projector icon [ ] on the taskbar while the desktop screen is displayed. 2 Click [Exit]. Desktop Control Utility 1.0 will be terminated. 3 Press the EXIT button on the projector unit or on the remote control. The “network menu”...

  • Page 203: Controlling The Projector Over A Lan (Pc Control Utility Pro 4)

    Wireless LAN (Optional: NP02LM series)” (→ page 139) and “9 Application Menus” (→ page 105) Start PC Control Utility Pro 4 Click “Start” → “All programs” or “Programs” → “NEC Projector User Supportware” → “PC Control Utility Pro 4” → “PC Control Utility Pro 4”.

  • Page 204: Converting Powerpoint Files To Slides (Viewer Ppt Converter 3.0)

    When Viewer PPT Converter 3.0 has been installed, once start Viewer PPT Converter 3.0 once with the privilege used for installation. Then exit from Viewer PPT Converter 3.0 without doing anything. • Starting Click Window’s [Start] → [All Programs] → [NEC Projector User Supportware] → [Viewer PPT Converter 3.0] → [Viewer PPT Converter 3.0], in that order. NOTE: When installing Viewer PPT Converter 3.0 onto a computer that has PowerPoint installed, Viewer PPT Converter 3.0 is automatically...
  • Page 205 8. User Supportware 5. Select the USB memory drive for “Card Drive” and type in “Index name”. Index name must be eight alphanumeric characters or less. 2-byte character and file with a long filename cannot be used. 6. Click “Export”. A confirmation message will be displayed.

  • Page 206: Projecting Your Mac's Screen Image From The Projector Over A Lan

    8. User Supportware  Projecting Your Mac’s Screen Image from the Projector over a LAN (Image Express Utility 2 for Mac) Using Image Express Utility 2 for Mac contained allows you to send the Mac’s screen image to the projector over a network (wired or wireless LAN).

  • Page 207: Using Image Express Utility 2

    8. User Supportware Using Image Express Utility 2 Connecting to a projector 1 Confirm that the projector has been turned on. 2 Click the AirPort status ( ) on the Macintosh menu bar, and click “Turn AirPort On”. The AirPort status is changed to “ ”...
  • Page 208 8. User Supportware 3 Double-click the “Image Express Utility 2” icon in the “Image Express Utility 2” folder. • At the initial start, the “License Agreement” window is displayed. Thoroughly read the agreement shown on the screen, and click “I accept the terms in the license agreement” and the [OK] button.
  • Page 209 8. User Supportware Stopping/Restarting Image Transmission • Stopping image transmission 1 Click [Tools] on the menu bar, and click [Stop Sending]. Image transmission is temporarily stopped. • Restarting image transmission 1 Click [Tools] on the menu bar, and click [Start Sending]. Image transmission is started again.

  • Page 210: Appendix

    9. Appendix 1 Troubleshooting This section helps you resolve problems you may encounter while setting up or using the projector. Indicator Messages Power Indicator Indicator Condition Projector Condition Note The main power is off – Blinking light Blue 0�5 sec On, The projector is getting ready to turn on�...

  • Page 211: Common Problems & Solutions

    9. Appendix Common Problems & Solutions (→ “Power/Status/Lamp Indicator” on page 192.) Problem Check These Items Does not turn on • Check that the power cord is plugged in and that the power button on the projector cabinet or the remote control or shut down is on�...

  • Page 212: If There Is No Picture, Or The Picture Is Not Displayed Correctly

    “Fn” key along with one of the 12 function keys gets the external display to come on or off. For example, NEC laptops use Fn + F3, while Dell laptops use Fn + F8 key combinations to toggle through external display selections.

  • Page 213: Specifications

    9. Appendix  Specifications This section provides technical information about projector’s performance. Model Number P420X/P350X/P350W Optical P420X P350X P350W LCD Panel 0.63 inch LCD with Micro Lens Array (Aspect Ratio 4:3) 0.59 inch LCD with Micro Lens Array (Aspect Ratio 16:10) Resolution* 1024 ×...
  • Page 214 Meets Low Voltage Directive (EN60950-1, TÜV GS Approved) For additional information visit: US : http://www.necdisplay.com/ Europe : http://www.nec-display-solutions.com/ Global : http://www.nec-display.com/global/index.html For information on our optional accessories, visit our website or see our brochure. The specifications are subject to change without notice.

  • Page 215: Cabinet Dimensions

    9. Appendix  Cabinet Dimensions Unit: mm (inch) 398 (15.7) 134 (5.3) Lens center Lens center 24 (0.9) 175 (6.9) Holes for ceiling mount 200 (7.9)

  • Page 216: Pin Assignments Of D-Sub Computer Input Connector

    9. Appendix  Pin Assignments of D-Sub COMPUTER Input Connector Mini D-Sub 15 Pin Connector Pin No. RGB Signal (Analog) YCbCr Signal 11 12 13 14 15 Green or Sync on Green Blue Ground Signal Level Ground Video signal : 0.7Vp-p (Analog) Red Ground Cr Ground Sync signal : TTL level...

  • Page 217: Compatible Input Signal List

    9. Appendix  Compatible Input Signal List Analog RGB HDMI Resolution Refresh Rate Resolution Refresh Rate Signal Aspect Ratio Signal Aspect Ratio ( dots ) ( Hz ) ( dots ) ( Hz ) 640 × 60/72/75/85/ 640 × iMac SVGA 800 ×...

  • Page 218: Pc Control Codes And Cable Connection

    9. Appendix  PC Control Codes and Cable Connection PC Control Codes Function Code Data POWER ON POWER OFF INPUT SELECT COMPUTER 1 INPUT SELECT COMPUTER 2 INPUT SELECT HDMI INPUT SELECT VIDEO INPUT SELECT S-VIDEO INPUT SELECT VIEWER INPUT SELECT NETWORK INPUT SELECT USB DISPLAY PICTURE MUTE ON PICTURE MUTE OFF...

  • Page 219: Troubleshooting Check List

    9. Appendix  Troubleshooting Check List Before contacting your dealer or service personnel, check the following list to be sure repairs are needed also by referring to the “Troubleshooting” section in your user’s manual. This checklist below will help us solve your problem more efficiently.
  • Page 220 Native resolution: Refresh rate: Video adapter: Other: Projector DVD player Video equipment VCR, DVD player, Video camera, Video game or other Signal cable NEC standard or other manufacturer’s cable? Manufacturer: Model number: Length: inch/m Model number: Distribution amplifier Model number: Switcher...

  • Page 221: Travelcare Guide

    9. Appendix  TravelCare Guide TravelCare - a service for international travelers This product is eligible for “TravelCare”, NEC’s unique international warranty and repair service. For more information on TravelCare service, visit our website (in English only). http://www.nec-display.com/dl/en/pj_support/travel_care.html...
  • Page 222 © NEC Display Solutions, Ltd. 2010 7N951552...

This manual is also suitable for:

Np-p350xNp-p420xP420xP350xP350wP350wg

Table of Contents