Thermal Cut-Out; Removing And Fitting The Blade; Environmental Information - Flymo EASIMO EM032 - NOTICE 2 Original Instructions Manual

Maintenance and storage
1. Caution: Do not touch rotating blade(s)
2. Keep all nuts, bolts and screws tight to be sure the
product is in safe working condition.
3. Check the grassbox frequently for wear or deterioration.
4. Replace worn or damaged parts for safety.
5. Only use the replacement parts specified for this product.
CH
T o ensure you have a secure connection between the
lawnmower and the extension cable we strongly recommend
you use the following method of attaching the cable:
1. Plug the short connection lead into the socket of the
extension cable. (M1).
The Motor is protected by a Thermal Cut-Out which is
activated when the blade becomes jammed or if the motor
is overloaded. When this occurs, stop and remove the
plug from the power supply. The Thermal Cut-Out will only
Switch off, wait until the blade has stopped rotating
and disconnect from the mains electricity supply
BEFORE attempting to remove or refit the blade.
Always handle the blade with care - sharp edges
could cause injury. USE GLOVES.
Removing the Blade
R1 - blade bolt R2 - washer
1. To remove the blade bolt, hold the blade firmly with a
gloved hand and with a spanner, loosen the blade
bolt by turning it anti-clockwise (R).
2. Remove the blade bolt, washer and blade.(R)
3. Inspect for damage and clean as necessary.
4. In the event of a blade becoming difficult to remove, insert a
screwdriver (S1) into the hole (S2) to lock the drive, then
• Awareness of the environment must be considered
when disposing of ʻend-of-lifeʼ product.
• If necessary, contact your local authority for disposal
information.
The symbol on the product or on its packaging
indicates that this product may not be treated as household
waste. Instead it shall be handed over to the applicable
collection point for the recycling of electrical and electronic
If any part is found to be defective due to faulty
manufacture within the guarantee period, Husqvarna
UK Ltd., through its Authorised Service Repairers will
effect the repair or replacement to the customer free of
charge providing:
(a) The fault is reported directly to the Authorised Repairer.
(b) Proof of purchase is provided.
(c) The fault is not caused by misuse, neglect or faulty
adjustment by the user.
(d) The failure has not occurred through fair wear and tear.
(e) The machine has not been serviced or repaired,
taken apart or tampered with by any person not
authorised by Husqvarna UK Ltd..
(f) The machine has not been used for hire.
(g) The machine is owned by the original purchaser.
(h) The machine has not been used commercially.
* This guarantee is additional to, and in no way
diminishes the customers statutory rights.
Failures due to the following are not covered, therefore
it is important that you read the instructions contained in
this Operator's Manual and understand how to operate
Safety

Thermal Cut-Out

Removing and Fitting the Blade

R3 - blade

Environmental Information

Guarantee and Guarantee Policy
ENGLISH - 2
6. Be careful during adjustment of the product to
prevent entrapment of the fingers between moving
blades and fixed parts of the machine.
7. Store in a cool dry place and out of reach of
children. Do not store outdoors.
8. Allow the product to cool for atleast 30 minutes
before storing.
2. Form a loop in the end of the extension cable near to
the socket and secure this in the strain relief feature at
the top of the switchbox. (M2) This will cause the
socket to hang in a downward direction. (M3)
reset when the start/stop lever is released. Clear any
obstruction and wait for a few minutes for the Thermal Cut-
Out to reset before continuing to use the mower.
use a spanner to loosen the blade bolt by turning the
spanner anti-clockwise. Ensure the screwdriver is removed
before atempting to turn on the machine.
Renew your metal blade after 50 hours mowing or 2
years whichever is the sooner - regardless of
condition. If the blade is cracked or damaged
replace it with a new one.
Fitting the Blade
1. Fit the blade to the shaft with the sharp edges of the
blade pointing away from the shaft.
2. Re-assemble blade bolt through the washer and the
blade.
3. Hold the blade firmly with a gloved hand and tighten the
blade bolt firmly with a spanner . Do not over tighten.
equipment. By ensuring this product is disposed of
correctly, you will help prevent potential negative
consequences for the environment and human health,
which could otherwise be caused by inappropriate waste
handling of this product. For more detailed information
about recycling of this product, please contact your local
council office, your household waste disposal service or the
shop where you purchased the product.
and maintain your machine:
Failures not covered by guarantee
* Failures as a result of not reporting an initial fault.
* Failures as a result of sudden impact.
* Failures as a result of not using the product in
accordance with the instructions and recommendations
contained in this Operator's Manual.
* Machines used for hire are not covered by this
guarantee.
* The following items listed are considered as wearing
parts and their life is dependent on regular
maintenance and are, therefore not normally subject to
a valid warranty claim: Blades, Electric Mains cable
* Caution!
Husqvarna UK Ltd. does not accept liability under the
warranty for defects caused in whole or part, directly or
indirectly by the fitting of replacement parts or
additional parts that are not either manufactured or
approved by Husqvarna UK Ltd., or by the machine
having been modified in any way.