Playing A Cd; Using The Display - Sony ZSS2IPW Service Manual

Playing a CD

1
Press CD qs (direct power-on).
2
Press Z PUSH OPEN/CLOSE 7 and place a disc
with the label side up in the CD compartment.
To close the CD compartment, press Z PUSH OPEN/
CLOSE 7 .
3
Press u 8 .
The player plays all the tracks once.
Track
number
To Press
u 8
Pause playback
To resume play, press it again.
x 8
Stop playback
> 6
Go to the next
track
. 6
Go back to the
previous track
Locate a point (forward) or
> .
6
while listening to while playing and hold it until
the sound you find the point.
Locate a point (forward) or
> .
6
while observing in pause and hold it until you
the display find the point.
Remove the CD PUSH OPEN/CLOSE
Z

Using the display

To check the total track number and playing
time
In stop mode, press DISPLAY•ENTER
5 on the remote.
To check the remaining time
5
Press DISPLAY•ENTER or DISPLAY
remote repeatedly while playing a CD. The display
changes as follows:
The current track number and playing time
B
r
The current track number and the remaining
time of the current track*
r
The number of tracks left and remaining
time on the CD
* For a track whose number is more than 20, the remaining time
appears as "- -:- -" in the display.
Selecting the play mode
Press MODE 4
and " ", "PGM", or "PGM" and " " appear in
the display. Then proceed as follows:
To Select Select
Repeat a "
single track
Repeat all " "
tracks
Shuffle play "SHUF"
Repeat tracks "SHUF"
in random and " "
order
Program "PGM"
play
Playing
time
Programed
track
Repeat "PGM"
programed and " "
tracks
(backward)
To cancel the selected play mode
Press MODE 4
disappears from the display.
(backward)
To check the programed track and playing
order in the display
7
To check the order of tracks before play, press
DISPLAY•ENTER
Every time you press the button, the track number
appears in the programed order.
To change the current program
x 8
Press once if the CD is stopped and twice if the
CD is playing. The current program will be erased.
Then create a new program following the programing
5 or DISPLAY
procedure.
Tip
You can play the same program again, since the program is saved
until you open the CD compartment.
5
on the
Listening to the radio
1
Press RADIO•BAND•AUTO PRESET
repeatedly (direct power-on) or press RADIO
and press BAND
Each time you press the button, the indication
changes as follows:
"FM" y "AM"
2
Hold down TUNE + or –
digits begin to change in the display.
The player automatically scans the radio frequencies
and stops when it finds a clear station.
If you can't tune in a station, press the button
repeatedly to change the frequency step by step.
When an FM stereo broadcast is received, "ST"
appears.
Tips
• If the FM broadcast is noisy, press MODE
in the display and the radio will play in monaural.
• If you touch or operate an iPod connected to this unit while
listening to AM/FM, noise may occur. Avoid touching or operating
the iPod in this case.
• If you hear noise from the AM/FM while supplying power to
iPod ("DC OUT" indicator appears in the display), press and hold
MODE for a few seconds to stop the power supply to the iPod ("DC
OUT" indicator disappears from the display).
until " 1", " ", "SHUF", "SHUF"
Then do this
> 6
1" Press or to
.
select the track that you want
u 8
to repeat, then press .
u 8
Press .
u 8
Press .
u 8
Press .
Press or > 6 then
.
5
press DISPLAY•ENTER
qk
or ENTER on the remote
for the tracks (up to 20) you
want to program in the order
u 8
you want. Then press .
Playing
order
Press or > 6 then
.
5
press DISPLAY•ENTER
qk
or ENTER on the remote
for the tracks (up to 20) you
want to program in the order
u 8
you want. Then Press .
repeatedly until the selected mode
5 qk
or ENTER on the remote.
qs
qs
qj
repeatedly on the remote.
9
until the frequency
4 until "Mono" appears
ZS-S2iP
Presetting radio stations
You can store radio stations into the player's memory.
You can preset up to 30 radio stations, 20 for FM and 10
for AM in any order.
1
Press RADIO•BAND•AUTO PRESET
BAND qj on the remote to select the band.
2
Hold down RADIO•BAND•AUTO PRESET
or RADIO qs on the remote for 2 seconds until
"AUTO" flashes in the display.
3
Press DISPLAY•ENTER 5 or ENTER
remote.
The stations are stored in memory from the lower
frequencies to the higher ones.
If a station cannot be preset automatically
You need to preset a station with a weak signal
manually.
1
Press RADIO•BAND•AUTO PRESET
BAND qj on the remote to select the band.
2
Tune in a station you want.
3
5
Hold down DISPLAY•ENTER or ENTER
on the remote for 2 seconds until the preset
number flashes in the display.
4
Press PRESET + or – 6 until the preset number
you want for the station flashes in the display.
5
Press DISPLAY•ENTER 5 or ENTER
remote.
The new station replaces the old one.
Tip
The preset radio stations remain in memory even if you unplug the
AC power cord or remove the batteries.
Playing preset radio stations
1
Press RADIO•BAND•AUTO PRESET
qj
BAND on the remote to select the band.
2
Press PRESET + or – 6 to tune in the stored
station.
Connecting optional components
You can enjoy the sound from an optional component
such as a portable digital music player through the
speakers of this unit. Be sure to turn off the power of
each component before making any connections. For
details, refer to the instruction manual of the component
to be connected.
1
Connect the AUDIO IN jack q; on the unit to
the line output jack of the portable digital music
player or other components using an audio
connecting cable (not supplied).
2
Turn the unit and the connected component on.
3
qs
Press AUDIO IN and start playing sound on
the connected component.
The sound from the connected component is output
from the speakers.
To connect the unit to a TV or VCR, use an extension
cable (not supplied) with a stereo-mini jack on one
end and two phono plugs on the other end.
qs
or
qs
qk on the
qs or
qk
qk on the
qs or
7