Fader Operations - Pioneer DJM-707 Operating Instructions Manual

FADER OPERATIONS

Adjusting Fader Lever Operating Sensation
Operating load adjust screw
(FEELING ADJ.)
The supplied hexagonal Allen driver can be used to adjust the
hexagonal Allen screw located next to the top panel's cross
fader slider opening, thus modifying the sliding resistance of
the lever. Rotate the screw clockwise to increase sliding
resistance and counterclockwise to reduce resistance.
1
Cross fader lag adjustment
The mechanical play (the lag or range of movement in which
no functional effect takes place) at the two extreme ends of
the top panel cross fader lever movement can be adjusted by
using the front panel's FADER CUT LAG dial, within a range
of 1-6 mm.
FADER CURVE
S FADER 1 CROSS
FADER CUT LAG
1
»
MIN MAX
Fader attenuation curve adjustment
The front panel's FADER CURVE dials can be used to adjust
the attenuation curve response of the cross fader and
channel fader. The cross fader can be adjusted independently
for CH-1 and CH-2 sides.
7 Channel fader curve adjustment (CH-1, CH-2)
LEVEL
0 1 2 3 4 5 6 7 8 9 10
Channel fader lever positions
7 Cross fader curve adjustment (CROSS FADER 1, 2)
LEVEL
Cross fader lever positions
12
<DRB1353>
REVERSE
2
FEELING
ADJ.
Lag Lag
REVERSE
0 1 2 3 4 5 6 7 8 9 10 0 1 2 3 4 5 6 7 8 9 10
Fader reverse function
The operating directions of the CH-1, CH-2 and cross fader
levers can be reversed by setting the front panel's FADER
REVERSE switches to their [ON] positions.
When the CH-1 (or CH-2) FADER REVERSE switch is set to
[ON], the top panel CH-1 (or CH-2) REVERSE indicator lights,
and the corresponding lever's operating direction is reversed
(scale mark "0" becomes attenuation 0 dB, while scale mark
"10" becomes minus infinity). The fader start function also
operates in reverse.
When the C.F. FADER REVERSE switch is set to [ON], the
top panel's cross fader REVERSE indicator lights, and the
lever operating direction is reversed (left side becomes CH-2
and right side becomes CH-1). The fader start function also
operates in reverse.
Fader Start Function
When the CH-1 and CH-2 jacks of this unit are connected to a
separately sold Pioneer DJ CD player (models CDJ-1000,
CDJ-1000MK2, CDJ-800, CDJ-100S, CDJ-700S, CDJ-500II,
CMX-3000, CMX-5000 or DMP-555), the channel fader and
cross fader functions can be used to automatically start
playback of the connected CD player (the applicable control
cord must be connected). By moving the mixer's channel
fader or cross fader lever, the CD player's pause function is
released and play starts instantly. Also, by returning the fader
2
lever to its original position, the CD player can be returned to
FEELING
its cue point (back cue function), thus allowing sampling
ADJ.
playback.
Cross fader start play and back cue play
When the CH-1 CD player is held in standby at the cue point,
merely moving the cross fader lever from the right (CH-2)
side to the left (CH-1) side will cause the CH-1 CD player to
begin playback.
When the cross fader lever reaches the left (CH-1) side, CH-2
CD player performs back cue (returns to its cue point).
Likewise, when the CH-2 CD player is in standby at its cue
point, moving the cross fader lever from the left (CH-1) side
to the right (CH-2) side causes CH-2 CD player to begin
playback. When the cross fader lever reaches the right (CH-2)
side, CH-1 CD player performs back cue.
FADER REVERSE
CH-1 C.F.
ON
OFF
FADER REVERSE
CH-1 C.F. CH-2
ON ON ON
OFF OFF OFF
CH-2
ON ON
PROFESSIONAL 2CHANNEL MIXER
OFF OFF
DJM-707
FADER CURVE
CH-1 CROSS FADER 1 CROSS FADER 2
FADER CUT LAG
MIN MAX
FADER START
PHONES
C.F. 1 CH-1 C.F. 2 CH-2
POWER
CH-2