Husqvarna 520iRX Operator's Manual
  1. Manuals
  2. Brands
  3. Husqvarna Manuals
  4. Trimmer
  5. 520iRX
  6. Operator's manual
Husqvarna 520iRX Operator's Manual

Husqvarna 520iRX Operator's Manual

Hide thumbs Also See for 520iRX:
Table of Contents

Advertisement

Quick Links

Download this manual
520iRX
EN
Operator's manual
2-26

Advertisement

Table of Contents
loading

Related Manuals for Husqvarna 520iRX

Summary of Contents for Husqvarna 520iRX

  • Page 1 520iRX Operator's manual 2-26...

  • Page 2: Table Of Contents

    Contents Introduction..............2 Maintenance..............19 Safety................4 Troubleshooting............21 Safety instructions for assembly........11 Transportation, storage and disposal......22 Safety instructions for maintenance......12 Technical data.............. 23 Assembly..............12 Accessories..............24 Operation..............15 Declaration of Conformity..........25 Introduction Product description the product for other tasks than grass trimming and grass clearing.
  • Page 3 3. Shaft The product agrees with the applicable 4. Harness quick release EC directives. 5. Harness, hip pad 6. Handle adjustment 7. Handlebar 8. Power trigger This product conforms to the applicable 9. Power trigger lockout UK regulations. 10. Keypad 11.

  • Page 4: Safety

    Noise emission to the environment label as per EU (also including New South Use and keep the battery charger indoors Wales legislation) and UK directives only. and regulations. The guaranteed sound power level of the product is specified in Technical data on page 23 and on the label Double insulation.
  • Page 5 • Do not abuse the cord. Never use the cord for controlled with the switch is dangerous and must be carrying, pulling or unplugging the power tool. Keep repaired. cord away from heat, oil, sharp edges or moving • Disconnect the plug from the power source and/or parts.
  • Page 6 • Follow all charging instructions and do not charge • Always use two hands when operating the machine. the battery pack or tool outside the temperature Holding the machine with both hands will avoid loss range specified in the instructions. Charging of control.
  • Page 7 replacement parts may increase the risk of breakage • Faulty cutting attachment can increase the risk of and injury. accidents. • Check the gear for dirt and cracks. Clean off grass Blade thrust causes and related warnings and leaves from the gear using a brush. Gloves should be worn when necessary.
  • Page 8 • Under no circumstances may the design of the you have to move suddenly. Take great care when product be modified without the permission of the you work on sloping ground. manufacturer. Always use original accessories. Non- • Walk, never run. authorized modifications and/or accessories can •...
  • Page 9 EU countries.Use visor for face protection. Visor is CAUTION: All servicing and repair work not enough to protect the eyes. on the machine requires special training. This is especially true of the machine′s safety equipment. If your machine fails any of the checks described below you must contact your service agent.
  • Page 10 1. Make sure that the power trigger is locked when the 1. Stop the product and remove the battery. lock is in its original position. 2. Do a visual check for damages, for example cracks. 3. Replace the cutting attachment guard if it is damaged.

  • Page 11: Safety Instructions For Assembly

    1. Stop the motor. correctly sharpened. Follow the instructions and use the recommended file gauge. 2. Do a visual check for damage for example, cracks. 3. Release and attach the quick release mechanism to WARNING: make sure that it operates correctly. A coasting blade can cause injury while it continues to spin after the switch has been released.

  • Page 12: Safety Instructions For Maintenance

    • A defective or incorrect guard can cause injury. Do of the cutting attachment. If the cutting not use a cutting attachment that does not have an attachment is install incorrectly it can result approved guard attached. in serious and/or fatal personal injury. •...
  • Page 13 3. Put on the harness and hang the product from the 2. Hang the trimmer guard on the hook on the plate suspension point. holder (A). 4. Adjust the handle to put the product in a good work 3. Bend the trimmer guard around the shaft and attach position.
  • Page 14 8. Install the locknut (G). Hold the shaft of the wrench • To loose and tighten the locknut, use a socket near the blade guard as much as possible. To spanner with a long shaft. The arrow in the picture tighten the locknut, you must turn the wrench shows the area where you should operate the socket counterclockwise which is the opposite direction of...

  • Page 15: Operation

    6. Let the cutting attachment lightly touch the ground. Note: If you use a grass blade, it must balance Adjust the harness clamp to balance the product approximately 10 cm /4 in above the ground. correctly. Operation Introduction • Make sure that the locking force on the locknut is not decreased.
  • Page 16 2. Put the plug in a grounded socket outlet. The LED on the battery charger flashes green one time. WARNING: Note: Only use Husqvarna The battery does not charge if the battery original batteries with the product. temperature is more than 50 °C/122 °F. If the temperature is more than 50 °C/122 °F, the battery...
  • Page 17 To operate the product 1. Push the rotation direction button to change the rotation direction. Automatic shutdown function The product has an automatic shutdown function that stops the product if the product is not used. The green LED for start/stop indication goes off and the product stops after 120 seconds.
  • Page 18 4. Use 80 % throttle when you cut grass near objects. 3. Move the product from side to side when you cut grass. Use full speed. To clear grass 1. Keep the trimmer head above the ground. 2. Tilt the trimmer head. 3.

  • Page 19: Maintenance

    To set the handlebar in transport 5. Use a sideway movement from left to right for the return stroke. position 6. Do the work rhythmically. 1. Loosen the knob. 7. Move forward and keep feet tightly against the ground. 2. Turn the handlebar clockwise until the throttle handle touches the battery.
  • Page 20 Maintenance Daily Weekly Monthly Make sure that the cutting attachment is not damaged. Replace the cutting attachment if it is damaged. Make sure that the cutting attachment guard is not damaged. Replace the cut- ting attachment guard if it is damaged. Make sure that the screws and nuts are tight.

  • Page 21: Troubleshooting

    3. Remove the nut that holds the trimmer head and the WARNING: Always discard a blade drive disc. that is damaged. Do not try to make a bent or twisted blade straight and use it again. • To sharpen the grass knife or grass blade correctly, refer to the instructions that come with the cutting attachment.

  • Page 22: Transportation, Storage And Disposal

    Battery Problem Possible faults Possible solution Green LED flashes. Low battery voltage. Charge the battery. Red error LED flashes. The battery is empty. Charge the battery. Temperature deviation. Use the battery in temperatures between -10°C (14°F) and 40°C (104°F). Overvoltage. Remove the battery from the battery charger.

  • Page 23: Technical Data

    Vibration levels at handles, measured according to ISO 22867, m/s Equipped with trimmer head (original), left/right 1.2/0.7 The Husqvarna Handheld Battery products marked with IPX4 fulfils these requirements on product approval level Noise emissions in the environment measured as sound power (L ) in conformity with EC directive 2000/14/ EC.

  • Page 24: Accessories

    520iRX Equipped with grass blade (original), left/right 2.8/1.6 Approved batteries Battery BLi200 40-B220X Type Lithium-ion Lithium-ion Battery capacity, Ah Nominal voltage, V Weight, kg (lb) 1.3 (2.9) 1.4 (3.1) Approved battery chargers Battery charger QC330 QC500 Input voltage, V 100-240...

  • Page 25: Declaration Of Conformity

    Declaration of Conformity EU Declaration of conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Battery-operated Grass Trimmer Brand Husqvarna Type / Model 520iRX Identification Serial numbers dating from 2023 and onwards...
  • Page 26 Declaration of conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Battery-operated Grass Trimmer Brand Husqvarna Type / Model 520iRX Identification Serial numbers dating from 2023 and onwards complies fully with the following UK regulations:...
  • Page 27 757 - 008 - 16.02.2024...
  • Page 28 Original instructions 1143939-26 2024-02-21...

Table of Contents