Smeg PVA750A Manual
  1. Manuals
  2. Brands
  3. Smeg Manuals
  4. Hob
  5. PVA750A
  6. Manual
Smeg PVA750A Manual

Smeg PVA750A Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
1. Precautions for safety and use_________________________ 4
3. Safety instructions __________________________________ 6
4. Fitting the appliance in the top _________________________ 7
4.1 Fixing to the supporting structure ________________________________________7
4.2 Fitting the adhesive foam rubber strip_____________________________________8
4.3 Fitting the fixing clips _________________________________________________8
4.4 Fitting the hob into the hole in the work-top ________________________________8
5. Electrical connection ________________________________ 9
6. Gas connection ___________________________________ 12
6.1 Connection to liquid gas ______________________________________________12
6.2 Room ventilation ____________________________________________________12
6.3 Combustion gas discharge ____________________________________________12
7. Adapting to different types of gas______________________ 13
7.1 Removing the hob skin _______________________________________________13
7.2 Burner and nozzle characteristics table __________________________________14
7.3 Hob burner layout ___________________________________________________14
7.4 Adjusting the primary air flow __________________________________________14
7.5 Reassembling the hob skin____________________________________________15
7.7 Adjusting the minimum setting for liquid gas_______________________________15
7.8 Greasing the gas taps________________________________________________15
8. Description of controls ______________________________ 16
8.1 The front panel _____________________________________________________16
9. Using the hob _____________________________________ 17
9.1 Fitting the pan stands ________________________________________________17
9.2 Lighting burners with safety device______________________________________20
9.3 Practical hints for using the burners _____________________________________20
9.4 Pan diameters______________________________________________________20
10. Cleaning and maintenance_________________________ 21
10.1 Cleaning the hob____________________________________________________21
10.3 Cleaning the components _____________________________________________21
Thank you for choosing our product.
We advise you to read this manual carefully. It contains all necessary instructions for
maintaining unaltered the appearance and functional qualities of the cooking hob.
INSTRUCTIONS FOR THE INSTALLER: these are intended for the authorized
person who is to check the gas supply system and install, commission and test the
appliance.
INSTRUCTIONS FOR THE USER: these provide recommendations for use, a
description of the controls and the correct procedures for cleaning and maintaining the
appliance.
Contents
3

Advertisement

Table of Contents
loading

Related Manuals for Smeg PVA750A

Summary of Contents for Smeg PVA750A

  • Page 1: Table Of Contents

    INSTRUCTIONS FOR THE INSTALLER: these are intended for the authorized person who is to check the gas supply system and install, commission and test the appliance. INSTRUCTIONS FOR THE USER: these provide recommendations for use, a description of the controls and the correct procedures for cleaning and maintaining the appliance.

  • Page 2: Precautions For Safety And Use

    Precautions for Safety and Use Precautions for safety and use THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE. TAKE GOOD CARE OF IT AND KEEP IT TO HAND THROUGHOUT THE HOB'S LIFE CYCLE. USERS ARE ADVISED TO READ THIS MANUAL AND ALL THE INSTRUCTIONS IT CONTAINS BEFORE USING THE HOB.

  • Page 3: Instructions For Disposal - Our Enviromental Care

    Do not throw the packing or any part of it away. They can constitute a suffocation hazard for children, especially the plastic bags. Your old appliance also needs to be disposed of correctly.

  • Page 4: Safety Instructions

    IT IS OBLIGATORY FOR ALL ELECTRICAL SYSTEMS TO BE GROUNDED ACCORDING TO THE METHODS REQUIRED BY SAFETY RULES. THE PLUG TO BE CONNECTED TO THE POWER SUPPLY CABLE AND ITS SOCKET MUST BE OF THE SAME TYPE AND CONFORM TO THE REGULATIONS IN FORCE.

  • Page 5: Fitting The Appliance In The Top

    Instructions for the Installer Fitting the appliance in the top If the hob has to be adapted for a type of gas different from the one for which it is preset in the factory, make this adjusting before building it into the unit, following the instructions in point “5.

  • Page 6: Fitting The Adhesive Foam Rubber Strip

    (fig. B). 4.4 Fitting the hob into the hole in the work-top Take special care when fitting the hob into the work-top. If the procedures are not carried out correctly, exactly as described, the hob may be damaged.

  • Page 7: Electrical Connection

    This nameplate must never be removed. The plug on the end of the power supply lead and the wall socket must be of the same type and comply with the relevant regulations. Check that the power supply line is properly earthed.

  • Page 8: Clearances Above And Around Domestic Appliances

    Range hoods and exhaust fans shall be installed in accordance with the manufacturer’s instructions. However, in no case shall the clearance between the highest part of the hob of the cooking appliance and a range hood be less than 600 mm or, for an overhead exhaust fan, 750 mm.
  • Page 9 2. The ‘cooking surface area’ is defined as that part of the appliance 3. where cooking normally takes place and does not include those parts of the appliance containing control knobs. 4. For definition of hob, see Clause 1.4.64.

  • Page 10: Gas Connection

    Ensure appliance is secured to wall when installation is completed. N.G. The regulator supplied must be fitted to the ½ BSP thread at the rear of the appliance. An approved manual shut-off valve must be installed. The N.G. regulator must be checked and adjusted to 1.0kPa after installation.

  • Page 11: Adapting To Different Types Of Gas

    The appliance is tested with NG (2H) natural gas at the pressure of 1 kPa. If it is to be used with other types of gas, the burner nozzles have to be changed and the primary air flow adjusted.

  • Page 12: Burner And Nozzle Characteristics Table

    7.4 Adjusting the primary air flow Refers to the gap “X” in mm. ULPG Natural Gas BURNER 1.0 kPa 2.75 kPa Auxiliary Semi rapid Rapid open Ultra Rapid To identify the burners on your hob, refer to the drawings in point “7.3 Hob burner layout”.

  • Page 13: Reassembling The Hob Skin

    “7.2 Burner and nozzle characteristics table”. 7.8 Greasing the gas taps Over time, the gas taps may become stiff or jam. Clean their insides and change their lubricating grease. This operation must be carried out by a skilled technician.

  • Page 14: Description Of Controls

    5 Burner Hob KNOB OPERATING MODE To light the flame, press the knob and at the same time turn it anti-clockwise to the minimum flame symbol . To adjust the flame, turn the knob to the zone between the maximum...

  • Page 15: Using The Hob

    D on the hob. 9.1 Fitting the pan stands The pan stands are supplied dismantled from the hob. To place each pan stand on its burner correctly, follow the instructions provided below: Each rack must be positioned on the corresponding burner in order to guarantee proper operation.
  • Page 16 Make sure that the pan stands are simply fitted over their burners, and are not left in a raised or tilted position; if this occurs, repeat the fitting procedure.
  • Page 17 Instructions for the User After performing the operations described above (for each pan stand), the hob will be as shown below, with the feet of the pan stands forming a pattern of horizontal and vertical lines. If a pan wobbles noticeably, check that the pan stands have not been fitted...

  • Page 18: Lighting Burners With Safety Device

    When the burner has lit, its control knob will light up to confirm that it is in operation. The knob will go out a few seconds after it is turned to the O position, or if the burner goes out accidentally. The knob light comes on and goes out gradually.

  • Page 19: Cleaning And Maintenance

    Never use a jet of steam for cleaning the appliance. 10.1 Cleaning the hob To keep the hob in good condition, it must be cleaned regularly, after each use, first allowing it to cool. 10.1.1 Routine daily glass hob cleaning When cleaning and caring for glass surfaces always use only specific products which do not contain abrasives or chlorine-based acids.
  • Page 20 The burner pins A must be fitted into the recesses B in the flame diffuser ring. The holes C in the flame diffuser ring must mate with the ignition plugs and thermocouples D on the hob.

This manual is also suitable for:

Pva750a-1Pvs750a

Table of Contents