Ventilation Function Crisp Finish; Drying", Page - Bosch CMG7761 1A Series User Manual And Installation Instructions

Press ⁠ "Cooking time".
5.
A cooking time must always be set to operate the
microwave.
To change the preset cooking time, press the relev-
6.
ant time value, e.g. minute display "m" or second
display "s".
a The selected value is marked in blue.
Use the setting ring to set the cooking time.
7.
If required, use to reset the setting value.
To confirm the set cooking time, press
8.
play.
Press to start the operation.
9.
a The microwave starts and the cooking time counts
down. The display shows the performance reduction
for the maximum microwave output "Boost".
→ "Microwave output settings", Page 12
a When the time has elapsed, a signal tone sounds. A
notification appears on the display confirming that
the operation has finished.
10. Once the cooking time has elapsed:
If required, you can select other settings and re-
‒
start the operation.
When the food is ready, use
‒
pliance off.
If you have switched off the drying function for the
11.
microwave in the basic settings and condensation
has formed in the cooking compartment, dry the
cooking compartment.
→ "Drying", Page 28
Note: If you open the appliance door during operation,
the operation stops. If you close the appliance door,
you must continue the operation. If you have changed
the basic setting for this, make sure that the microwave
does not resume operation without food inside.
→ "Basic settings", Page 22
Changing the microwave output
You can change the microwave output at any time.
Press on the display.
1.
Press the microwave output
2.
Use the setting ring to set the microwave output.
3.
To confirm the change, press
4.
a The change is applied.
Changing the cooking time
You can change the cooking time at any time.
Press on the display.
1.
Ventilation function "Crisp Finish"
12 Ventilation function "Crisp Finish"
The ventilation function "Crisp Finish"
ture from the cooking compartment so that your food
will be more crispy.
Hot steam that may escape when the appliance door is
opened is reduced.
12.1 Suitable types of heating with the
ventilation function
Only certain types of heating are suitable for the ventil-
ation function.
You can use the ventilation function for the following
types of heating:
¡ 4D hot air
on the dis-
to switch the ap-
⁠ .
on the display.
extracts mois-
Ventilation function "Crisp Finish" en
Press the cooking time
2.
Use the setting ring to change the cooking time.
3.
To confirm the change, press
4.
a The change is applied.
11.4 Setting added microwave
Note:
Note the correct way to operate the microwave:
¡ → "Safety", Page 2
¡ → "Preventing material damage", Page 6
¡ → "Microwave output settings", Page 12
¡ → "Cookware and accessories with microwave",
Page 17
Requirement: Observe the information about the re-
spective operating mode.
→ "Setting options with the microwave", Page 18
Press the operating mode that you require in the
1.
menu.
Select the settings for the operating mode, e.g. type
2.
of heating and temperature.
Press ⁠ "Added microwave".
3.
Use the setting ring to set the microwave output.
4.
To confirm the set microwave output, press
5.
the display.
Press ⁠ "Cooking time" and set the cooking time.
6.
Press to start the operation.
7.
a The appliance starts to heat and the time counts
down.
a When the time has elapsed, a signal sounds. A
message appears on the display confirming that the
operation has finished.
Once the cooking time has elapsed:
8.
If required, you can select other settings and re-
‒
start the operation.
When the food is ready, use
‒
pliance off.
Changing added microwave
You can change or deactivate the added microwave at
any time.
Press on the display.
1.
Press the microwave output
2.
Change or deactivate added microwave with the
3.
setting ring.
To confirm the change, press
4.
a The change is applied.
¡ Top/bottom heating
¡ Circulated air grilling
¡ Pizza setting
12.2 Setting the ventilation function
You can activate the ventilation function at any time,
even after the start of the operation.
Set a suitable type of heating and a temperature.
1.
If required, you can select other settings and com-
bine with the ventilation function.
Press ⁠ "Crisp Finish".
2.
a The symbol lights up red.
⁠ .
on the display.
on
to switch the ap-
⁠ .
on the display.
19