Table of Contents
Advertisement
ASSEMBLY
Recharge only with the charger
WARNING
specified for the battery. For
specific
charging
operator's manual supplied with your charger
and battery.
Inserting/Removing the Battery
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
Only use accessories specifically
WARNING
recommended
Others may be hazardous.
To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
Always remove the battery pack
WARNING
any time the tool is not in use.
Only use accessories with Maximum Safe
Operating Speed rated at least equal to the
maximum speed marked on the power tool. This
speed is based on the strength of the
accessory, allowing for a reasonable measure
of safety. It is not meant to imply a best or most
efficient operating speed. Do not exceed the
Maximum Safe Operating Speed.
To reduce the risk of injury, always clean
mandrels before inserting them into the collet
and securely tighten the collet nut and.
Otherwise the high-speed rotation of the tool
could force the accessory to fly out of the collet.
Everyone in the area must wear protective
clothing and safety goggles or face shields.
Damaged accessories may fly apart with
considerable
force,
serious injury.
Installing Accessories
Remove battery to avoid starting
1.
WARNING
the tool.
2.
To remove the nose cover, twist to the UNLOCK
position and pull away from the tool. The nose
cover can be used for toolless accessory
changing.
instructions,
read
for
this
causing
potential
3. Remove dust and debris from the
collet, collet nut, and accessory
shank.
4. Insert the collet into the spindle.
the
5. Loosely screw the collet nut onto
the spindle.
6.
Insert the accessory shank into
the collet at least 19 mm (3/4").
7.
Press in the spindle lock button
and
tighten
securely using the nose cover
tool.
(or a 9.5 mm (3/8") collet
wrench).
NOTE: Do not tighten the collet
nut
without
installed. This could damage the collet.
WARNING
the use, care and protection of accessories.
Typical Applications
A large variety of accessories are available for
applications such as grinding, sanding, and cutting.
Grinding/Sanding
Use sanding and grinding accessories that are:
less than 55 mm in diameter.
•
• correct accessory type and grit for the job.
• rated at or above the RPM listed on the tool's
nameplate.
Wheel Brushes
Wire wheel brushes are useful for removing rust,
scale, burrs, weld slag, etc. A wide variety of wire
brushes are available for many applications. When
applying brush to work, avoid using too much
for
pressure. This causes over-bending of wires and
heat build-up resulting in premature wire breakage,
rapid dulling and reduced brush life. Instead of
using more pressure, try a wire wheel brush with
more aggressive cutting action (increased wire size,
decreased wire length or different brush type, i.e.
knot type instead of crimped wire type).
Cutting
Always handle cutting wheels carefully to avoid
damage. Before installing any wheel, always in-
spect it for cracks. If wheel is cracked, discard it to
prevent others from using it. Cutting wheels should
be protected from:
• wetness and extreme humidity
• any type of solvent
• extreme changes in temperature
• dropping and bumping
If a cutting wheel encounters any of these situations,
discard the wheel immediately.
WARNING
protection marked to comply with AS/NZS
1337.1.
When working in dusty situations, wear
appropriate respiratory protection or use a
suitable dust extraction solution.
To determine the amount of charge left in the
battery, turn the tool ON. The fuel gauge will light up
for 2-3 seconds. When less than 10% of charge is
left, 1 light on the fuel gauge will flash 4 times.
To signal the end of charge, 1 light on the fuel
6
the
collet
nut
an
accessory
To reduce the risk of injury, the
operator should be instructed in
OPERATION
Always use personal protective
equipment. Always
Fuel Gauge
wear
eye
Advertisement
Table of Contents
