Table of Contents
Advertisement
Using the Remote Control
The remote control can be operated regardless of the
hold mode of the unit.
Preparation:
Release the remote control from the hold mode.
\Hotpe J)
—
Operation confirmation tones
2
When an operation button is pressed, a confirmation tone
sounds. Aefer to the paretheses in the illustration tor the dif-
ferent types of confirmation tones.
How to use the wired remote contro!
Press once during otf or stop made.
To start play
To stop play
To turn off
the unit
Press once during play.
Forward
(Beep
Beap)
(Beep Beep
Beep)
Backward
Press and hold during play.
backward
When adjusting the volume using the remote
control, position the volume control on the
unit between 4 and 6.
To adjust the
volume
[Preparation
Installing the lithium battery
Back of remote control
Tha wireless remote control can be operated regardless of the
hold mode of the unit.
Do not place any object which will block the path of the signals
between the remote control and the unit.
#Do not allow the remote sensor or transmitter to become dusty.
®Do not leave the remote contra) standing in direct suntight or in
high temperature locations in a car.
sin the interest of traffic safety, do not operate tha remote control
while driving.
Taka every care to prevent small children trom putting the lithi-
um battery in their mouths or swallowing it. In the event that a
child has swallowed a battery, consult with a physician immedi-
ately.
Using the unit with an audio
system
Using stereo connection cable (not included), you can
hear CDs on your audio system.
Connect the cable to the amplifier after turning off its
power.
e Do not connect the cable to the PHONO jacks on the
amplifier.
Obtain
the optional connecting cable if the amplitier
comes with mini-phone jacks.
eAdjust the volume on the amplifier.
eSound quality changes when S-XBS is selected, but
volume is reduced by approximately fifty percent.
SL-$365 ONLY
When using active speakers or other speakers, ensure
that they have an input impedance of 1kQ or less.
Using the Unit with Optional Accessories
[Operation _
Preparation:
When the unit is to be operated using rechargeable batteries or dry cell batteries, first press > II on the unit and then use the remote
control, (The unit cannot be operated by the remote controi while the unit is turned off.)
Initiates play/establishes pause
mode when pressed again.
Stops play/tums the unit off when
' | kept depressed.
Skip tracks (tap).
Rapidly searches forward or
backward during play {keep
depressed}.
Repeats all tracks or single track.
Remote control's operating range
®Point the transmitter on the ramote control ai the remote sensor
on the unit.
Use the remote control within a 7-meter range of the remote
sensor on the unit,
(Depending on the angle of the remote control, the signals may
nat reach the sensor.)
OUT jack
Back panel of the unit
Amplifier
® To CD or AUX
* terminals
Stereo connection cable {not included)
How to use the hook and loop fastener
To prevent misplacament of the remote
control, it is recom-
mended that the hook and loop fastener be used as shown in the
figure below.
Back
of remote
control
eAdhere the hook and {oop fastener roughly in the canter of the
remote control's back surface.
Before adhering the hook and loop fastener, choose a flat and
even surface and wipe off any dirt.
i
® Avoid a location which is exposed to direct sunlight.
CAUTION:
The battery used in this device may present a risk of fire or
chemicat bum if mistreated. Do not recharge, disassembia,
heat above 100°C (212°F}, or incinerate. Replace battery
with Panasonic part number CR 2025/1P0D only. Use of an-
other battery may present a risk of fire or explosion.
Dispose of used battery promptly. Keep away trom children.
Do not disassemble end do not dispose of in fire.
—
-
Using the unit with a car audio
system
The SL-S361C/SL-S362C
come with the car adaptor and car
stereo cassette adaptor.
Please refer to the "Installation Instructions" (attached sheet).
Items to be purchased (SL-S360/SL-S365)
For connection to the car audio system
Car stereo cassette adaptor (SH-CDM10A)
Connect the car stereo cassette adaptor to the
, Unit's headphones jack.
` (When doing this, keep the unit's VOLUME con-
' trol at a setting between 4 and 6.)
For securing the unit and connecting the power
supply:
Car adaptor (SH-CDC9)
Car mounting kit (SH-CDF7)
Car mounting arm, Car insulator
It may not be possibla to use the unii with some types of car
stereos owing to restrictions imposed by the construction of the
Car Stereo cassette adaptor.
For further details, rater to the instructions of the part concerned,
RQT4834
Advertisement
Table of Contents
