Yamaha MU128 Sound List & Midi Data page 34

2.1.3 XG parameter change
This message sets XG-related parameters. Each message can
set a single parameter.
The message format is as follows.
11110000 F0H
01000011 43H
0001nnnn 1NH
01001100 4CH
0ggggggg GGH
0mmmmmmm MMH
0lllllll LLH
0sssssss SSH
: :
11110111 F7H
For parameters whose Data Size is 2 or 4, the appropriate
amount of data will be transmitted as indicated by Size.
2.1.3.1 XG System On
11110000 F0H
01000011 43H
0001nnnn 1NH
01001100 4CH
00000000 00H
00000000 00H
01111110 7EH
00000000 00H
11110111 F7H
When On is received, the SOUND MODULE
MODE will be set to XG.
Since approximately 50[ms] are required in order
to execute this message, please allow an
appropriate interval before transmitting the next
message.
2.1.3.2 XG System parameter change
This message sets the XG SYSTEM block (refer
to tables <1 -1>, <1 - 2>).
2.1.3.3 Multi Effect1 parameter change
This message sets the MULTI EFFECT1 block
(refer to tables <1 - 1>, <1 - 4>).
2.1.3.4 Multi EQ parameter change
This message sets the MULTI EQ block (refer to
tables <1 - 1>, <1 - 5>).
2.1.3.5 Multi Effect2 parameter change
This message sets the MULTI EFFECT2 block
(refer to tables <1 - 1>, <1 - 6>).
2.1.3.6 Display parameter change
This message sets the DISPLAY block (refer to
tables <1 - 1>, <1 - 7>).
Exclusive status
YAMAHA ID
N:device Number
Model ID
Address High
Address Mid
Address Low
Data
End of Exclusive
Exclusive status
YAMAHA ID
N:device Number
Model ID
Address High
Address Mid
Address Low
Data
End of Exclusive
MU128 MIDI
2.1.3.7 Multi Part parameter change
This message sets the MULTI PART block (refer
to tables <1 - 1>, <1 - 8>).
2.1.3.8 AD Part parameter change
This message sets the AD PART block (refer to
tables <1 - 1> , <1 - 9>).
2.1.3.9 AD System parameter change
This message sets the AD SYSTEM block (refer
to tables <1 - 1>, <1 - 10>).
2.1.3.10 Drums Setup parameter change
This message sets the DRUMS SETUP block
(refer to tables <1 - 1> , <1 - 11>).
2.1.3.11 Plugin board parameter change
This messages set the PLUGIN BOARD block
(refer to tables <1 - 1> , <1 - 12>).
2.1.4 MU128 native parameter change (1)
This message sets parameters unique to the MU128. Each
message sets a single parameter.
As indicated below, the message format is in common with
the MU50, MU80, MU90, and MU100.
11110000 F0H Exclusive status
YAMAHA ID
01000011 43H
N:Device Number
0001nnnn 1NH
01001001 49H Model ID
Address High
0ggggggg GGH
Address Mid
0mmmmmmm MMH
Address Low
0lllllll LLH
Data
0vvvvvvv VVH
: :
End of Exclusive
11110111 F7H
For parameters whose Data Size is 2 or 4, the number of
data bytes indicated by Size are transmitted.
2.1.4.1 MU128 System parameter
change
This message sets the SYSTEM block (refer to
tables <2 - 1>, <2 - 2>).
2.1.4.2 Remote Switch
This message sets the REMOTE SWITCH block
(refer to tables <2 - 1>, <2 - 3>).
2.1.5 MU128 native parameter change (2)
This message sets parameters which are unique to the
MU128. Each message modifies a single parameter.
The format of this message is the same as for the MU90 and
MU100, as shown below.
MIDI data format
35