Table of Contents
Advertisement
Recording
DISC
PROGRAM
KARAOKE
MODE
1
5
1
6
6
A
TIME
TIME
MODE
DISC SKIP
3
KARAOKE
4
REC/PAUSE
CENTER/
REAR/DELAY
KEY/ECHO
POWER
Display information during programming
Display information during programming
TRACK
VCD PBC
NR
TIMER
M
SLEEP
HALL
NOR TEST
MERSION
PHANTOM
Next play order
Selected track
number
TRACK
REM
NR
M
Programmed track numbers light up and
only programmable track numbers
among unprogrammed ones flash.
E-30
1
2
3
DISC
DISC
DISC CHANGE
OPEN / CLOSE
PRESET/ TUNING/ BAND
A/B/C/D/E
VOLUME
DOWN
UP
1
B.BOOST
MUSIC
INPUT
INPUT
RANDOM
REPEAT
TIME
TIME
HOUR
MIN
DOLBY NR
REC/PAUSE
AUTO/MANUAL
MEMORY
DISPLAY
TIMER
TIME ADJ
STANDBY/ON
2
3
4
5
2
3
4
5
7
8
PRESET
7
8
9
0
B
C
D
E
+
PROG
R. TIME
EDIT
I0
REPEAT
RANDOM
TUNER
TUNER
VCD
CD
/
9
TIME INDEX
RETURN
SELECT
7
INTRO
DIGEST
DIRECTION
T APE
1
BASS
TEST
PROGRAM
BOOST
MUSIC
LEVEL
INPUT
VOLUME
SLEEP
/I
Selected disc
TUNER
RANDOM
CD
1 2 3 4
5
6
EDIT
MD
S F REP
7 8 9 10
11
12
A
B
TAPE
PROG
13 14 15
OVER 15
Side of the tape
Total remaining time on
this side of the tape
CD
1 2 3 4
5
6
7 8 9 10
11
12
A
PROG
13 14 15
OVER 15
Manual EDIT recording
You can program tracks manually while watching the
remaining time on both sides of the tape.
1
Press INPUT
appears on the display, and load a disc (or discs) on the
disc tray.
2
Follow steps 3–5 on page 29.
3
Press PROG.
* "PROG" and "P-01" will light up on the display, and all
track numbers on the selected disc will begin flashing.
4
If necessary, select the desired disc by pressing DISC
SKIP.
5
Select the desired track number by pressing the numeric
buttons.
6
Repeat steps 4 and 5 to program more selections for side A
of the tape. You can select the same track again.
* Pressing TIME displays the total remaining time on side
A of the tape for about 1 second, and then it is replaced
by the display of the next play order.
* If "TM OVER" appears on the display, the track number
just selected cannot be programmed because there is
not enough time remaining on side A of the tape.
However, at this time, if any other track number is
flashing continuously on the display, you can program it
instead of the unprogrammable one.
7
When the programming for side A is finished, press
R. TIME.
* "Side–B" appears on the display. You can begin
programming for side B.
* After following this step, you can check the programmed
contents for side A and side B alternately by pressing
R. TIME at any time before you press EDIT in step 9.
* The tape side indicator (
side currently selected.
8
Repeat steps 4 and 5 to program selections for side B of
the tape. You can select the same track again.
VOLUME
9
Press EDIT. ("EDIT" (
The recording starts.
VOLUME
Notes on recording with the EDIT function
● To check, cancel or correct program data, refer to page 15.
● The maximum number of tracks that can be programmed is
20.
● The track number 16 or higher cannot be programmed by
this function.
or
once or more until "VCD/CD" (
9
) shows the programming
8
) lights up on the display.)
1
)
Advertisement
Table of Contents
