Related Manuals for NCR 7360-K066
Summary of Contents for NCR 7360-K066
- Page 1 Kit Instructions Tri-Light/Lane Light with Camera Assembly 7360-K066 Issue E Confidential and proprietary information of NCR. Unauthorized use, reproduction and/or distribution is strictly prohibited...
- Page 2 NCR, therefore, reserves the right to change specifications without prior notice. All features, functions, and operations described herein may not be marketed by NCR in all parts of the world. In some instances, photographs are of equipment prototypes. Therefore, before using this document, consult with your NCR representative or NCR office for information that is applicable and current.
-
Page 3: Revision Record
Configuring the Camera Settings using SADP Tool on page 22. Added Configuring the Camera Settings using Batch Configuration Tool on page 30. Added Installing Batch Configuration Tool on page 32. Confidential and proprietary information of NCR. Unauthorized use, reproduction and/or distribution is strictly prohibited. -
Page 4: Kit Contents
Tri-Light/Lane Light with Camera Assembly This publication provides procedures for installing a Tri-Light/Lane Light with Camera Assembly to an NCR SelfServ™ Checkout (7360) unit. Kit Contents Part Number Description 497-0525295 7360-K066 Tri-Light/Lane Light with Camera 497-0524107 Tri-Light/Lane Light with Camera Assembly * 006-8614045 Cable Tie - Nylon, 11 ⅜... - Page 5 Description * 497-0525183 Assy, Pack for SCO R6 Tri-Light with Camera 497-0511101 Lane Light Graphics Label – NCR Fastlane * 497-0423108 Instructions – Kit (Reference Sheet) * Items marked with an asterisk are not called out on the image. Confidential and proprietary information of NCR.
-
Page 6: Installation Procedures
To install the Tri-Light/Lane Light with Camera Assembly, follow these steps: Note Ensure that the NCR Customer Helpdesk is informed when the Tri- Light/Lane Light with Camera is installed in the store. 1. Remove the existing Tri-Light/Lane Light Assembly, if necessary. For more... - Page 7 Enter the following default login credentials: Username: admin Password: HikVision1 The browser opens a live feed of the camera, as shown in the image below. Confidential and proprietary information of NCR. Unauthorized use, reproduction and/or distribution is strictly prohibited.
- Page 8 Hikvision Network Camera User Manual. Note Ensure that the NCR Customer Helpdesk is informed when the Tri- Light/Lane Light with Camera is installed in the store. Confidential and proprietary information of NCR. Unauthorized use, reproduction and/or distribution is strictly prohibited.
- Page 9 Removing the Tri-Light/Lane Light (R6) To remove the Tri-Light/Lane Light Assembly, follow these steps: 1. Turn off the NCR SelfServ Checkout software and hardware systems. 2. Remove one (1) screw to detach the Tri-Light/Lane Light Assembly to the Tri-Light/Lane Light pole.
- Page 10 3. Lift the Tri-Light/Lane Light Assembly and then disconnect the cables. Mark all cables as to where they are connected to quickly determine the corresponding port when reconnecting the cables. Confidential and proprietary information of NCR. Unauthorized use, reproduction and/or distribution is strictly prohibited.
- Page 11 To install the Tri–Light/Lane Light Assembly, follow these steps: Note Ensure that the NCR Customer Helpdesk is informed when the Tri- Light/Lane Light with Camera is installed in the store. 1. Remove the existing Tri–Light/Lane Light assembly, if necessary. For more...
- Page 12 3. Connect the Tri–Light/Lane Light with Camera Assembly cables. Confidential and proprietary information of NCR. Unauthorized use, reproduction and/or distribution is strictly prohibited.
- Page 13 Ethernet cable to provide strain relief as shown in the image below. 5. Orient the Tri-Light/Lane Light Assembly so that the Lane Light faces the front of the unit. Confidential and proprietary information of NCR. Unauthorized use, reproduction and/or distribution is strictly prohibited.
- Page 14 LAN cable followed by the Power cable, and then the Tri– Light/Lane Light Assembly cable. Once the extenders are through the pole, slowly push the Tri–Light/Lane Light Assemby into pole. Confidential and proprietary information of NCR. Unauthorized use, reproduction and/or distribution is strictly prohibited.
- Page 15 8. Secure the Tri–Light/Lane Light assembly to the pole with a screw. 9. Run the ADD utility to ensure device is updated with the latest firmware. Confidential and proprietary information of NCR. Unauthorized use, reproduction and/or distribution is strictly prohibited.
- Page 16 Route the cable down the Scanner Bucket floor. Use cable ties to secure the cable on bridge lances. c. Secure the cable to the anchor using a cable tie. Confidential and proprietary information of NCR. Unauthorized use, reproduction and/or distribution is strictly prohibited.
- Page 17 Note For the Tri-Light/Lane Light with Camera Assembly, connect the Camera Power cable to the I/O Box (Input Belt port). Confidential and proprietary information of NCR. Unauthorized use, reproduction and/or distribution is strictly prohibited.
- Page 18 Secure the cable to the spiral cable manager at every notch using cable ties. d. Secure the cable to the anchor using a cable tie. Confidential and proprietary information of NCR. Unauthorized use, reproduction and/or distribution is strictly prohibited.
- Page 19 Note For the Tri-Light/Lane Light with Camera Assembly, connect the Camera Power cable to the I/O Box (Input Belt port). Confidential and proprietary information of NCR. Unauthorized use, reproduction and/or distribution is strictly prohibited.
- Page 20 3. Depending on the configuration, connect the Tri-Light cable to the Tri- Light/Lane Light port. Use cable ties to tie the cable on bridge lances. KIO and 150 W PSU Configuration I/O Box Configuration Confidential and proprietary information of NCR. Unauthorized use, reproduction and/or distribution is strictly prohibited.
- Page 21 Measure at least 100 mm length from the Tri-Light connector and make one (1) cable loop around the ferrite core, and then clamp the cable with the ferrite. Confidential and proprietary information of NCR. Unauthorized use, reproduction and/or distribution is strictly prohibited.
- Page 22 For the Tri-Light/Lane Light with Camera Assembly, mate the Camera Power cable to the Tri-Light Camera 12 V Power Cable, and then connect the cable to the CAB/TAB Port of the KIO Board. Confidential and proprietary information of NCR. Unauthorized use, reproduction and/or distribution is strictly prohibited.
- Page 23 I/O Box Configuration Note For the Tri-Light/Lane Light with Camera Assembly, connect the Camera Power cable to the I/O Box (Input Belt port). Confidential and proprietary information of NCR. Unauthorized use, reproduction and/or distribution is strictly prohibited.
-
Page 24: Configuring The Camera Settings
A. Obtain the IP address settings of the removed camera. This will be used to set the IP address of the new Camera. For more information, contact an NCR Representative or the Retailer's Help Desk. Note For new camera installation, IP Addresses are pre-allocated by the Retailer's IT Team. - Page 25 The SADP interface appears and displays active devices with corresponding IP addresses, as shown in the image below. 3. Select Refresh to update the devices listed and their corresponding information. Confidential and proprietary information of NCR. Unauthorized use, reproduction and/or distribution is strictly prohibited.
- Page 26 4. Modify the network parameters by the doing the following, if necessary: a. Select the camera to modify by checking the check box. b. Select the arrow on the right side of the interface. Confidential and proprietary information of NCR. Unauthorized use, reproduction and/or distribution is strictly prohibited.
- Page 27 The side panel opens and displays settings of the selected camera. c. Update the IP Address of the camera. d. Select Modify to save the changes. Confidential and proprietary information of NCR. Unauthorized use, reproduction and/or distribution is strictly prohibited.
- Page 28 1. Unzip the installation package to the DVA or lane. 2. Open the directory where the executable file is located. 3. Run the file. The SADP Tool setup window appears. SADPTool.exe Confidential and proprietary information of NCR. Unauthorized use, reproduction and/or distribution is strictly prohibited.
- Page 29 4. Select Next. The installation window shows the default destination folder. 5. Select Change to enter a different destination from the default destination folder, if necessary. Confidential and proprietary information of NCR. Unauthorized use, reproduction and/or distribution is strictly prohibited.
- Page 30 6. Select Next throughout the process to choose all default settings until the window notifies that installation is complete. A setup window for Win10Pcap appears once SADP installation is completed. Confidential and proprietary information of NCR. Unauthorized use, reproduction and/or distribution is strictly prohibited.
- Page 31 7. Select Next. The installation window shows the default destination folder. 8. Select Change to enter a different destination from the default destination location, if necessary. Confidential and proprietary information of NCR. Unauthorized use, reproduction and/or distribution is strictly prohibited.
- Page 32 9. Select Next to continue. The Windows Security Alert appears. 10. Select Next to proceed with the installation. The SADP Tool icon appears on the desktop once installation is completed. Confidential and proprietary information of NCR. Unauthorized use, reproduction and/or distribution is strictly prohibited.
- Page 33 Hikvision website. 2. Install the Batch Configuration Tool. For more information, refer to Installing Batch Configuration Tool on page 32. 3. Open the Batch Configuration Tool application. Confidential and proprietary information of NCR. Unauthorized use, reproduction and/or distribution is strictly prohibited.
- Page 34 4. Download the User Manual to access procedures specific to the parameter that needs to be configured. Confidential and proprietary information of NCR. Unauthorized use, reproduction and/or distribution is strictly prohibited.
- Page 35 Batch Configuration.exe 4. Do the following: a. Select the License Agreement check box and select Next. b. Select the Language option and select Next. and The installation Confidential and proprietary information of NCR. Unauthorized use, reproduction and/or distribution is strictly prohibited.
- Page 36 5. Select Change to enter a different destination from the default destination folder, if necessary. Confidential and proprietary information of NCR. Unauthorized use, reproduction and/or distribution is strictly prohibited.
- Page 37 6. Select Next to proceed with the installation. The Batch Configuration icon appears on the desktop once installation is completed. Confidential and proprietary information of NCR. Unauthorized use, reproduction and/or distribution is strictly prohibited.