Related Manuals for NCR 7358-K068
Summary of Contents for NCR 7358-K068
- Page 1 Kit Instructions R6L Plus Tri–Light/Lane Light with Camera Assembly 7358-K068 Issue A...
- Page 2 NCR, therefore, reserves the right to change specifications without prior notice. All features, functions, and operations described herein may not be marketed by NCR in all parts of the world. In some instances, photographs are of equipment prototypes. Therefore, before using this document, consult with your NCR representative or NCR office for information that is applicable and current.
-
Page 3: Revision Record
Revision Record Issue Date Remarks Dec 2019 First Issue... -
Page 4: Kit Contents
Tri–Light/Lane Light with Camera Assembly This publication provides procedures for installing a Tri–Light/Lane Light with Camera Assembly to an NCR FastLane SelfServ™ Checkout (7358) R6L Plus unit. Kit Contents Part Number Description 497-0527398 7358-K068 Kit, R6L+ Trilight with IP Camera 006-8624305 Rectangle Blanking Plug (42 x 23.8 mm) - Page 5 7358-K068 R6L Plus Tri-light/Lane Light with Camera Assembly Part Number Description 006-8623599 Plug - Locking, Flush, 9.5 mm Hole, Black (2 pcs) * 497-0523835 Cable - Tri-Light and Lane Light Extender 497-0521360 Tri-Light Pole - R6L Plus 009-0006598 Screws M6 x 20 (2 pcs)
-
Page 6: Installation Procedures
Assembly Installation Procedures To install the Tri–Light/Lane Light with Camera assembly, follow these steps: Note: Ensure that the NCR Customer Helpdesk is informed when the Tri–Light/Lane Light with Camera is installed in the store. 1. Do the following: • Remove the existing Tri–Light/Lane Light Assembly. For more information, refer Removing Tri–Light/Lane Light Assembly... - Page 7 7358-K068 R6L Plus Tri-light/Lane Light with Camera Assembly Username: Admin Password: HikVision1 The browser opens a live feed of the camera, as shown in the image below.
- Page 8 Right-hand (RH) orientation. For more information on setting the camera parameters, refer to Hikvision Network Camera User Manual. Note: Ensure that the NCR Customer Helpdesk is informed when the Tri–Light/Lane Light with Camera is installed in the store.
- Page 9 1. Turn off the R6L Plus software and hardware systems. For more information, refer to NCR FastLane SelfServ™ Checkout (7358) Hardware Service Guide (BCC5–0000–5265). 2. Remove the screw securing the Tri–Light/Lane Light Assembly to the Tri–Light /Lane Light pole.
- Page 10 7358-K068 R6L Plus Tri-light/Lane Light with Camera Assembly Tri–Light/Lane Light with Camera Assembly...
- Page 11 7358-K068 R6L Plus Tri-light/Lane Light with Camera Assembly 3. Lift the Tri–Light/Lane Light Assembly and then disconnect the cables. Tri–Light/Lane Light Assembly...
- Page 12 7358-K068 R6L Plus Tri-light/Lane Light with Camera Assembly Tri–Light/Lane Light with Camera Assembly Note: The assembly has cable ties that provide strain relief for the connectors. Cut these cable ties before disconnecting the connectors.
- Page 13 7358-K068 R6L Plus Tri-light/Lane Light with Camera Assembly Removing Tri–Light/Lane Light Pole To remove the Tri–Light/Lane Light pole, follow these steps: 1. Remove the existing Tri–Light/Lane Light assembly, if necessary. 2. Remove two screws securing the pole to the unit.
- Page 14 7358-K068 R6L Plus Tri-light/Lane Light with Camera Assembly Installing Lane Light Label To install the label on each side of the Lane Light, follow these steps: 1. Remove the Tri–Light/Lane Light assembly, if necessary. 2. Wipe any dust or dirt on the surface of both sides of the Lane Light.
- Page 15 7358-K068 R6L Plus Tri-light/Lane Light with Camera Assembly 4. Position the label on the Lane Light. Ensure that the label is flush with the front edge of the Lane Light, as shown in the image below. 5. Hold half of the label in place while peeling off the protective film from the other half of the label and then attach the label on the Lane Light, as shown in the image below.
- Page 16 7358-K068 R6L Plus Tri-light/Lane Light with Camera Assembly 6. Peel off the adhesive tape from the other half of the label and then attach the label to the Lane Light. Note: For the purpose of illustration only, the image below shows a Lane Light (FastLane) label.
- Page 17 7358-K068 R6L Plus Tri-light/Lane Light with Camera Assembly Installing Tri–Light/Lane Light Pole To install the Tri–Light/Lane Light pole, follow these steps: 1. Insert the Tri–Light/Lane Light cable extender through the Tri–Light/Lane Light pole. Tip: To make routing the cable extender through the pole easier, first attach a weight (for example, a large bolt) to a long piece of string and drop the weighted end of the string through the Tri–Light/Lane Light pole (starting at the top-end).
- Page 18 7358-K068 R6L Plus Tri-light/Lane Light with Camera Assembly 3. Secure the pole to the Upper Cabinet using two screws. 4. Install the Tri–Light/Lane Light assembly.
- Page 19 Installing Tri–Light/Lane Light with Camera Assembly To install the Tri–Light/Lane Light assembly, follow these steps: Note: Ensure that the NCR Customer Helpdesk is informed when the Tri–Light/Lane Light with Camera is installed in the store. 1. Remove the existing Tri–Light/Lane Light assembly, if necessary. For more information, refer to Removing Tri–Light/Lane Light Assembly...
- Page 20 7358-K068 R6L Plus Tri-light/Lane Light with Camera Assembly 3. Connect the Tri–Light/Lane Light with Camera Assembly cables.
- Page 21 7358-K068 R6L Plus Tri-light/Lane Light with Camera Assembly 4. Install three (3) cable ties on each side of the power connector and on the Ethernet cable to provide strain relief as shown in the image below. 5. Orient the Tri–Light/Lane Light assembly so that the Lane Light faces the front of...
- Page 22 7358-K068 R6L Plus Tri-light/Lane Light with Camera Assembly 6. Insert the Tri–Light/Lane Light assembly into the Tri–Light/Lane Light pole. Ensure that the pole holes are aligned. Tip: To easily insert the cables with connectors through the pole, insert first the LAN cable followed by the Power cable, and then the Tri–Light/Lane Light Assembly...
- Page 23 7358-K068 R6L Plus Tri-light/Lane Light with Camera Assembly 7. Connect the Tri–Light/Lane Light and Power cables to the corresponding I/O Box port destinations: Tri–Light Destination Connection (Location) Tri–Light/Lane Light cable extender I/O Box (Tri–Light/Lane Light port) Ethernet (LAN) cable extender Ethernet (LAN) I/O Box (Power) cable extender...
-
Page 24: Configuring Camera Settings
Before configuring the camera settings, do the following: A. Obtain the IP address settings of the removed camera. This will be used to set the IP address of the new Camera. For more information, contact an NCR Representative or the Retailer's Help Desk. - Page 25 7358-K068 R6L Plus Tri-light/Lane Light with Camera Assembly 2. Select Refresh to update the devices listed and their corresponding information. 3. Modify the network parameters by the doing the following, if necessary: a. Select the camera to modify by checking the check box.
- Page 26 7358-K068 R6L Plus Tri-light/Lane Light with Camera Assembly Installing SADP Tool The Search Active Devices Protocol (SADP) is an online device search tool that allows users to search and to modify network information of online devices. For more information about SADP Tool, refer to HikVision Tools Download.
- Page 27 7358-K068 R6L Plus Tri-light/Lane Light with Camera Assembly 4. Select Next. The installation window shows the default destination folder. 5. Select Change to enter a different destination from the default destination folder, if necessary.
- Page 28 7358-K068 R6L Plus Tri-light/Lane Light with Camera Assembly 6. Select Next throughout the process to choose all default settings until the window notifies that installation is complete. A setup window for Win10Pcap appears once SADP installation is completed.
- Page 29 7358-K068 R6L Plus Tri-light/Lane Light with Camera Assembly 7. Select Next. The installation window shows the default destination folder. 8. Select Change to enter a different destination from the default destination location, if necessary.
- Page 30 7358-K068 R6L Plus Tri-light/Lane Light with Camera Assembly 9. Select Next to continue. The Windows Security Alert appears. 10. Select Next to proceed with the installation. The SADP Tool icon appears on the desktop once installation is completed.