Advertisement
Quick Links
Advertisement
Related Manuals for NCR 1659-K001
Summary of Contents for NCR 1659-K001
- Page 1 Kit Instructions N4000 Mount Bracket 1659-K001 Issue A...
- Page 2 NCR, therefore, reserves the right to change specifications without prior notice. All features, functions, and operations described herein may not be marketed by NCR in all parts of the world. In some instances, photographs are of equipment prototypes. Therefore, before using this document, consult with your NCR representative or NCR office for information that is applicable and current.
-
Page 3: Table Of Contents
Table of Contents N4000 Mount Bracket Introduction Kit Components Required Tools Installation Procedures Rack Mount Installation Wall Mount Installation... - Page 4 Revision Record Issue Date Remarks Feb 2019 First Issue...
-
Page 5: N4000 Mount Bracket
N4000 Mount Bracket Introduction This Mount kit provides a solution for mounting the NCR N4000 Site Controller on a rack or to a wall. -
Page 6: Kit Components
N4000 Mount Bracket Kit Components Part Number Description 1 497-0480060 (4) #6-32 x 0.23in Step Pan Head Flat Screw 2 497-0480061 #6-32 x 0.3120in Machine Phillips Pan Head, SEMS, Black 3 497-0522067 N4000 19-inch Mount Bracket 4 497-0522155 N4000 Power Supply Velcro Strap... -
Page 7: Required Tools
N4000 Mount Bracket Required Tools Rack Mount installation requires the following tools: • Phillips screwdriver • Cable ties as needed Wall Mount installation requires the following tools: • Phillips screwdriver • Pencil or marker • (4) ¼–20 toggle bolts or similar, depending on mounting substrate — supplied by customers •... -
Page 8: Installation Procedures
N4000 Mount Bracket Installation Procedures Refer to the appropriate section below according to your installation requirement: • Rack Mount Installation on the facing page • Wall Mount Installation on page 9... -
Page 9: Rack Mount Installation
N4000 Mount Bracket Rack Mount Installation 1. Use the mounting holes on the left and right tabs of the Mount Bracket to secure the bracket to the rack. 2. Lay the N4000 face down on a flat surface. - Page 10 N4000 Mount Bracket 3. Insert the four Step Pan Head Flat Screws into the hole locations marked with a W. 4. Position the N4000 over the bracket, mount the four Step Pan Head Flat Screws onto the bracket, and slide the N4000 forward to lock it in place. Note: The N4000 can be mounted on the bracket with its port on the front side or on the rear side.
- Page 11 N4000 Mount Bracket Caution: Ensure that all four screws are fully inserted into the bracket.
- Page 12 N4000 Mount Bracket 5. On the rear side, secure the N4000 with the included security screw. 6. Use the Velcro Strap to secure the Power Supply at the side of the bracket. Note: Route and tie the power cord in place as needed.
-
Page 13: Wall Mount Installation
N4000 Mount Bracket Wall Mount Installation 1. Mark the Mount Bracket screw holes on the wall. a. Using the Mount Bracket as a template, hold it against the wall and mark the four holes. Take note of the "up" arrow indicating the correct orientation of the bracket. - Page 14 N4000 Mount Bracket 3. Lay the N4000 face down on a flat surface. 4. Insert the four Step Pan Head Flat Screws into the hole locations marked with a W.
- Page 15 N4000 Mount Bracket 5. Position the N4000 beside the bracket, mount the four Step Pan Head Flat Screws onto their slots on the bracket, and slide the N4000 downward to lock it in place. Note: The N4000 can be mounted on the bracket with its port on the top side or on the bottom side.
- Page 16 N4000 Mount Bracket 6. On the bottom side, secure the N4000 with the included security screw. 7. Insert the Power Supply into the power supply pocket on the bracket. Note: Route and tie the power cord in place as needed.