Table of Contents
Advertisement
Quick Links
NX2 Pocket Toner
The NX2 Pocket Toner lets you quickly do tests
for continuity, short circuits, ac and dc voltage,
Ω
Ω
and 50
or 75
termination. The standard
adapters let you use the toner on cable with
F-type connectors. Optional adapters let you
use the toner on twisted pair, coaxial, and
two-wire radial cable.
The optional Dial Tone Detective
quickly see if a dial tone is present at a
telephone jack and if the polarity of the wires
is correct.
Safety Information
Warning or Caution: Risk of damage
to or destruction of equipment or
software. See explanations in the
manual.
Warning: Risk of electrical shock.
PN 3968817 January 2011, Rev. 2 3/12
©2011 Fluke Corporation. Printed in China. All product
names are trademarks of their respective companies.
Pocket Toner
®
, Speed 81™, and Dial Tone Detective™ are
trademarks of Gale Corporation.
®
Users Guide
™
lets you
Advertisement
Table of Contents
Related Manuals for Fluke Pocket Toner NX2
Summary of Contents for Fluke Pocket Toner NX2
- Page 1 Warning: Risk of electrical shock. PN 3968817 January 2011, Rev. 2 3/12 ©2011 Fluke Corporation. Printed in China. All product names are trademarks of their respective companies. Pocket Toner ® , Speed 81™, and Dial Tone Detective™ are...
- Page 2 Do not connect this equipment to public communications networks, such as telephone systems. See the warning below. Do not put products that contain circuit boards into waste containers. Refer to local regulations for disposal procedures. Warning To prevent possible fire, electric shock, or personal injury: •...
-
Page 3: Auto Shut-Off
Features Speaker Test port Display Power Adapter Main unit Battery cap Speed 81 coupler* Toner cap * F-type coupler that helps you make connections faster. Auto Shut-Off The main unit turns off if the condition of the line does not change for 10 minutes. - Page 4 How to Use the Toner For unterminated cable, connect the correct adapter to an ID cap or the toner cap, then connect the cap to the far end of the cable. Connect the correct adapter to the main unit. Turn on the main unit, then connect it to the near end of the cable.
- Page 5 How to Detect Dial Tones Connect the optional Dial Tone Detective to a telephone jack. To hear a tone when a dial tone is present, use the Speed 81 coupler to connect the toner cap to the Dial Tone Detective. If there is a dial tone, the green LED is on.
-
Page 6: Maintenance
You cannot repair or replace parts in the case. • Use only replacement parts that are approved by Fluke Networks. • If you replace parts that are not specified as replacement parts, the warranty will not apply to the product and you can make the product dangerous to use. -
Page 7: Specifications
How to Replace the Battery Specifications Approximate distance: 300 m (1,000 ft) Output voltage in continuity mode: 3.6 Vdc (with a new battery) Toner frequency: Main unit: 2.7 kHz. Toner cap: 2.3 kHz Maximum input voltage: 30 Vac, 42 Vpk, or 60 Vdc Battery type: 1.5 V AAA alkaline Auto shut-off: 10 minutes... -
Page 8: Contacting Fluke Networks
Union directives Conforms to relevant Australian standards Listed by the Canadian Standards Association CSA C22.2 No. 61010.1.04 Contacting Fluke Networks www.flukenetworks.com support@flukenetworks.com +1-425-446-4519 • Australia: 61 (2) 8850-3333 or 61 (3) 9329 0244 • Beijing: 86 (10) 6512-3435 •... -
Page 9: Limited Warranty And Limitation Of Liability
LIMITED WARRANTY AND LIMITATION OF LIABILITY Fluke Networks mainframe products will be free from defects material workmanship for one year from the date of purchase. Parts, accessories, product repairs and services are warranted for 90 days, unless otherwise stated. Ni-Cad, Ni-MH and Li-Ion batteries, cables or other peripherals are all considered parts or accessories.