Table of Contents
Advertisement
6: Installing KOT-2 (Fig. 3-5)
For installation on the PLL unit, proceed as in item 5.
In this case, the cable assembly with plug is not sup-
plied with the CTCSS unit.
©)
Fig. 3-4
KQT-2
QL
LL
"Tp
79 RA
J6
4 || /-—=
©
coo
eee
Wks
D
ome)
; =
5
/ 3
g
|
|
he O-—
OWE
PLL unit
!
©)
=
Oo
|
O05
5/°
O
q O
BOTTOM VIEW
Fig. 3-5
3-4
: Conversion to 16CH with KOT-1
The only difference from item 7 is that cable plug P9
is now connected to CTCSS unit J31.
Cable: E31-2182-05
: Conversion to 32CH without signalling or CTCSS
Basically the same as in item 7. Use the 32CH
revi-
sion kit in lieu of the 16CH kit and connect the brown
and the red leads (cut in item 7) to the $2 AUX switch
on the TX-RX unit, as shown.
TX-RX
unit
MON
AUX
(a)
®
©
0
0
0
fH
Red
0
JU!
a
ie
"
Brown
Fig. 3-6
10:
11:
12:
13:
Conversion to 32CH with KQT-1
Connecting the cable plug P9 to CTCSS
unit J31
is
the only difference from item 9.
Installing time-out timer KTT-1.
(Fig. 3-7)
Install the Time-out timer in place on the PLL unit as
shown.
Connect Time-out timer plug P45 to PLL unit
J5, then open PLL unit JU3.
8
Time-out timer
N)
ame)
| a
\
i
|
Cc
Hl
or
O
J!
ol((F
PLL unit
:
(@)
a
|
——
S06
oO
00
%
FIN
BOTTOM VIEW
Fig. 3-7
Perform
operating
frequency
realignment,
following
the alignment procedure, page 5-7.
For RCC
(1) obtain kit;
KCH-1C (RCC kit for TK-801S)
KCH-1D
(RCC kit for TK-701S)
(2) Cut off the red lead @ from the 16 channel
switch.
Cut off the brown lead © from the 16 channel
switch.
(3)
(4)
(5)
Install the rotary switch to the chassis.
Pass the brown lead ©, cut in item (2), under the
VOL and SQL bracket and solder it to panel side
of AUX switch.
Solder the brown lead @ to the common side.
Install the channel knob.
Install PLL unit (X50-1970-21) JU14.
@RED
3-5
(6)
Replace
the
escutcheon
panel
with
the
RCC
panel.
TK-801S: A21-0758-04
TK-701S: A21-0759-04
Attach the escutcheon
panel with double-faced
adhesive tape.
:
PLL unit
Loin
ér
O
©
|
O
O
@BRN
og
© BRN
E31-2176-05
BOTTOM VIEW
Fig. 3-8
@ BRN
MON
AUX
a)
x
x
oO
DOD
'@)
0
tt)
0
0.0 CO D
©
© BRN
~
£31-2176-05
~
@ | To PLL-J9
Fig. 3-9
(7) Operation
ROM (out position):
Pre-programmed
frequencies
change by the 16
channel switch.
HOME (in position):
Pre-programmed
HOME
frequency
pair is auto-
matically selected at "H".
Advertisement
Table of Contents
