Installation Installationshinweise Achten Sie bei der Installation darauf, dass keine serienmäßig im Kfz vorhandenen Teile wie z.B. Kabel, Bordcomputer, Sicherheitsgurte, Tank oder ähnliche Teile beschädigt bzw. entfernt werden. Vergewissern Sie sich, dass der Verstärker an dem Montageort genügend Kühlung erhält. Montieren Sie das Gerät nicht in zu kleine, abgeschlossene Gehäuse ohne Luftzirkulation, in die Nähe von wärmeabstrahlende Teilen oder elektronische Steuerungen des Fahrzeuges.
Funktionen & Bedienelemente TXi 4000 / TXi 6000 HI-/LOW PASS - Regler HI PASS (Hochpass) - regelt die Begrenzung des Frequenzgangs der Lautsprecher nach unten. Die Trennfrequenz ist stufenlos von 10Hz bis 1200Hz (1.2kHz) regelbar. LOW PASS (Tiefpass) - regelt die Begrenzung des Frequenzgangs der Lautsprecher nach oben. Die Trennfrequenz ist stufenlos von 30Hz bis 150Hz regelbar.
Lautsprecher- & Cinchanschlüsse TXi 4000 / TXi 6000 2-Kanal-Modus Stereo Front- oder Hecksystem Kabelanschlüsse • Verbinden Sie die Ausgänge des Steuergerätes (Radio) mit den Cincheingängen (LINE INPUT) des Verstärkers mittels einer geeigneten hochwertigen Cinchleitung. • Verbinden Sie die Front- oder Hecklautsprecher mittels geeignetem Kabel mit den Lautsprecher-Ausgängen des Verstärkers (SPEAKER OUTPUT / + 1CH - und + 2CH -).
Lautsprecher- & Cinchanschlüsse TXi 4000 / TXi 6000 1-Kanal-Modus Mono Subwoofer gebrückt Kabelanschlüsse • Verbinden Sie die Ausgänge des Steuergerätes (Radio) mit den Cincheingängen (LINE INPUT) des Verstärkers mittels einer geeigneten hochwertigen Cinchleitung. • Verbinden Sie den Subwoofer mittels geeignetem Kabel mit den Lautsprecher-Ausgängen des Verstärkers (SPEAKER OUTPUT / + Mono bridged -).
Funktionen & Bedienelemente TXi 4400 / TXi 5400 / TXi 6400 / TXi 8400 HI-/LOW PASS - Regler CH1/2 & CH3/4 HI PASS (Hochpass) - regelt die Begrenzung des Frequenzgangs der Lautsprecher nach unten. Die Trennfrequenz ist stufenlos von 10Hz bis 1200Hz (1.2kHz) regelbar. LOW PASS (Tiefpass) - regelt die Begrenzung des Frequenzgangs der Lautsprecher nach oben.
Fehlerbehebung Fehler: keine Funktion Ursache: 1. Die Verbindungskabel sind nicht korrekt angeschlossen. 2. Die Kabel haben keinen elektrischen und mechanischen Kontakt. 3. Sicherungen defekt. Im Falle des Austauschs achten Sie bitte auf den korrekten Wert der Sicherungen. Fehler: kein Ton aus Lautsprecher Ursache: 1.
Technische Daten TXi 4000 TXi 6000 TXi 4400 TXi 5400 TXi 6400 TXi 8400 Kanäle 2 x 100/200 2 x 150/300 4 x 70/140 4 x 75/150 4 x 90/180 4 x 150/300 Watt RMS/MAX. an 4 Ohm 2 x 200/400 2 x 300/600 4 x 125/250 4 x 125/250...
Installation Installation Notes The amplifier is generally mounted in the rear trunk area but can be mounted in any convenient area such as beneath a seat. Please be sure to locate this unit where you have reasonable air circulation and protection from moisture. When considering the mounting location you should minimize the length of the power and speaker leads.
Functions & Controls TXi 4000 / TXi 6000 HI-/LOPASS HI PASS (HighPass) Controls the frequency response of your speakers downwards. The Cut-off frequency is continously variable from 10Hz up to 1200Hz (1.2kHz). LOW PASS (LowPass) Controls the frequency response of your speakers upwards. The Cut-off frequency is continously variable from 30Hz up to 150Hz. If the X-OVER - Switch is set on LP/BP-position, so the HI PASS-controller is activated as Subsonic-Filter, who eliminates the lowest frequencies to protect the speakers from damages.
Speaker & RCA Connections TXi 4000 / TXi 6000 2-Channel-Mode Stereo Front- or Rearsystem RCA & Speaker wiring: • Connect the LINE INPUT of the amplifier to the head unit line output with appropriate good quality RCA cables. • Connect the speakers with appropriate wires to the terminal block (SPEAKER OUTPUT/ - CH1 + and - CH2 +) of the amplifier. •...
Speaker & RCA Connections TXi 4000 / TXi 6000 1-Channel-Mode Mono Subwoofer bridged RCA & Speaker wiring: • Connect the LINE INPUT of the amplifier to the head unit line output with appropriate good quality RCA cables. • Connect the subwoofer with appropriate wires to the terminal block (SPEAKER OUTPUT/ - Mono bridged +) of the amplifier. •...
Functions & Controls TXi 4400 / TXi 5400 / TXi 6400 / TXi 8400 HI-/LOPASS CH1/2 & CH3/4 HI PASS (HighPass) Controls the frequency response of your speakers downwards. The Cut-off frequency is continously variable from 10Hz up to 1200Hz (1.2kHz). LOW PASS (LowPass) Controls the frequency response of your speakers upwards.
Speaker & RCA Connections TXi 4400 / TXi 5400 / TXi 6400 / TXi 8400 4-Channel-Mode Stereo Front- and Rearsystem RCA & Speaker wiring: • Connect the LINE INPUT of the amplifier to the head unit line output with appropriate good quality RCA cables. •...
Speaker & RCA Connections TXi 4400 / TXi 5400 / TXi 6400 / TXi 8400 3-Channel-Mode 2 Mono Subwoofer bridged RCA & Speaker wiring: • Connect the LINE INPUT of the amplifier to the head unit line output with appropriate good quality RCA cables. •...
Speaker & RCA Connections TXi 4400 / TXi 5400 / TXi 6400 / TXi 8400 3-Channel-Mode Stereo Front- or Rearsystem & Mono Subwoofer bridged RCA & Speaker wiring: • Connect the LINE INPUT of the amplifier to the head unit line output with appropriate good quality RCA cables. •...
Troubleshooting System does not turn on 1. Check all fuses. 2. Check all connections. 3. Measure the +12 volt and remote turn on voltages at the amplifier terminals. If these are non existent or low, take voltage measurements at fuse holders, distribution blocks, the head unit’s +12 volt and remote leads to localize the problem. Noise problems 1.Check the speaker wiring 2.Speakers are damaged...
Specifications TXi 4000 TXi 6000 TXi 4400 TXi 5400 TXi 6400 TXi 8400 Channels 2 x 100/200 2 x 150/300 4 x 70/140 4 x 75/150 4 x 90/180 4 x 150/300 Watts RMS/MAX. into 4 Ohm 2 x 200/400 2 x 300/600 4 x 125/250 4 x 125/250...