Table of Contents
Advertisement
Disassembly Procedures
!
WARNING
Spark Module
1. Turn off gas and power supply to the cooktop.
2. Release control panel cover, see "Control Panel and
Indicator Light(s)" procedure, steps 1 through 6.
3. Locate spark module needing replace, (individual
spark modules are located above each burner valve).
4. Disconnect and label wire terminals from spark
module.
5. Remove screws securing spark module to burner box
area.
6. Replace component and reverse procedures to
reassemble.
Thermostat (Selector or Safety)
1. Turn off gas and power supply to the cooktop.
2. Release control panel cover, see "Control Panel"
procedure, steps 1 through 6.
3. Remove screws securing thermostat bracket to
mounting bracket.
4. Disconnect and label wire terminals from thermostat.
5. Open oven door and remove screws securing front
oven vent cover to the front of oven cavity.
6. Remove thermostat bulb from bracket.
7. Maneuver thermostat bulb through oven cavity and
burner box bottom to remove.
8. Replace component and reverse procedure to
reassemble.
Door Latch Assembly
1. Turn off gas and power supply to the cooktop.
2. Open oven door and remove screws securing front
oven vent cover to the front of oven cavity.
3. Remove oven vent cover with door latch assembly
from unit.
4. Disconnect and label wire terminals from latch
assembly.
5. Remove screws securing latch assembly to oven vent
cover.
6. Replace component and reverse procedure to
reassemble.
Fan TCO
1. Turn off gas and power supply to the cooktop.
2. Open oven door and remove screws securing front
oven vent cover to the front of oven cavity.
3. Remove oven vent cover with door latch assembly
from unit.
4. Disconnect and label wire terminals from TCO.
5. Remove screws securing fan TCO to oven vent cover.
6. Replace component and reverse procedure to
reassemble.
18
To avoid the risk of electrical shock, personal injury or
death; disconnect power to range and shut off gas
supply before following any disassembly procedure.
Selector Switch Assembly
1. Turn off gas and power supply to the cooktop.
2. Release control panel cover, see "Control Panel"
procedure, steps 1 through 6.
3. Remove screws securing selector switch bracket to
mounting bracket.
4. Disconnect and label wire terminals from selector
switch.
5. Remove screws securing selector switch to selector
switch bracket.
6. Replace component and reverse procedure to
reassemble.
Oven Light Switch
1. Turn off gas and power supply to the cooktop.
2. Release control panel cover, see "Control Panel"
procedure, steps 1 through 6.
3. Disconnect wire terminals from oven light switch.
4. Remove nut securing oven light switch to control
panel.
5. Replace component and reverse procedure to
reassemble.
Manifold Pipe
1. Turn off gas and power supply to the cooktop.
2. Remove grates and burner bowls trim pieces from
cooktop surface.
3. Remove screws securing sealed burner tops to orifice
holders.
4. Raise sealed burner tops and disconnect wire
terminals from spark ignitors.
5. Remove burner bowls from cooktop surface.
6. Disconnect main gas supply line from gas regulator.
7. Release control panel cover, see "Control Panel"
procedure, steps 1 through 6. Do not remove.
8. Remove screws securing thermostat bracket to
mounting bracket.
9. Remove burner valves from manifold.
10. Remove bolts securing manifold to mounting
brackets.
11. Remove screw securing manifold to burner box.
12. Remove manifold from unit.
13. Remove gas regulator from manifold.
14. Replace component and reverse procedure to
reassemble.
NOTE: When installing, use pipe dope compound.
Perform gas leak test to ensure unit will not leak
and cooktop operates properly.
16026509
© 2005 Maytag Services
Advertisement
Table of Contents
