Table of Contents
Advertisement
2. Press
(B10) or
on the display (B);
3. Press "
" to start rinsing.
Important! Danger of burns.
Do not leave the appliance unattended while hot water is being
delivered.
4. After a few seconds, hot water is delivered first from the
coffee spouts, then from the hot water/steam spout (if
inserted) to clean and heat the appliance's internal circuit.
"RINSING UNDERWAY, HOT WATER FROM SPOUTS" appears
on the display, together with a progress bar which fills
gradually as preparation proceeds;
5. To stop rinsing, press "
stop automatically.
Please note!
•
If the appliance is not used for more than 3-4 days, when
you turn it on again, we strongly recommend performing
2/3 rinses before use;
•
After cleaning, it is normal for the grounds container (A10)
to contain water.
8.2 Descaling
For instructions on descaling, see section "19. Descale".
8.3 Water filter
For instructions on how to install the filter (C4), see section "21.
Water softener filter".
8.4 Beverages settings
In this section, you can consult your customised settings and, if
you wish, reset the default values for each beverage, except cold
coffee, cold milk and chocolate.
1. Press "
" (B2) to enter the menu;
2. Press
(B10) or
appears on the display (B);
3. Press "
". The values for the first beverage appear on the
display;
4. The reference user profile is highlighted on the display. The
values are displayed on vertical bars. The default value is
indicated by the
highlighted by the solid part of the vertical bar;
5. To go back to the settings menu, press "
To scroll and display the beverages, press "
6. To reset the default values for the beverage displayed, press
"
RESET";
7. "CONFIRM RESET?": to confirm, press "
press "
");
8. "DEFAULT VALUES SET": press "
(B8) until "
RINSING" appears
" or wait for rinsing to
(B8) until "
DRINKS SETTINGS"
symbol, while the current value is
".
" (to cancel,
".
The beverage has been reset to the default values. Continue with
the other beverages, or go back to the settings menu.
Please note!
•
To change the beverages in another profile, go back to the
homepage, select the required profile (B11) and repeat the
procedure.
•
To reset all the beverages in the profile, see section "8.18
Default values "
8.5 Adjust time
To adjust the time on the display (B), proceed as follows:
1. Press "
2. Press
(B10) or
on the display (B);
3. Press "
". The time setting panel appears on the display;
4. Press
or
until the current time is displayed;
5. To confirm, press "
then press "
The time is now set.
8.6 Auto-start
You can set the auto-start time in order to have the appliance
ready at a certain time (for example in the morning) so you can
make coffee immediately.
Please note!
To enable this function, the time must already be set correctly
(see section "8.5 Adjust time
To enable auto-start, proceed as follows:
1. Press "
2. Press
(B10) or
pears on the display (B);
3. Select the function by pressing "
panel appears on the screen;
4. Press
or
until the required auto-start time is displayed;
5. Press
auto-start.
6. To confirm, press "
the settings menu by pressing "
" to go back to the homepage.
The auto-start time is now set and the corresponding symbol is
";
displayed to indicate that the function has been enabled.
Please note!
When the appliance is turned off using the main switch (A21),
the auto-start setting (if enabled) is lost.
10
" (B2) to enter the menu;
(B8) until "
corresponding to the hours and minutes
" (to cancel, press "
" to go back to the homepage.
").
" (B2) to enter the menu;
(B8) until "
corresponding to the hours and minutes
or
to enable or disable
" (or cancel and go back to
SET TIME" appears
"),
AUTO-START" ap-
". The time setting
"), then press "
Advertisement
Table of Contents
Troubleshooting
